Tools And Materials Required For Installation - Vogelzang International TR001WS Owner's Manual

NOTICE: No warranty, stated or implied, has been granted for the installation or maintenance of this stove
and assumes no responsibility of any incidental or consequential damages.

TOOLS AND MATERIALS REQUIRED FOR INSTALLATION

(NOTE: The following items are NOT included with your stove and are required for proper installation.)
• Flooring Protection as specified
• Chimney Connection: 6"/152mm dia. minimum 24
MSG black or
• 26 MSG blue steel straight stove pipe or elbow(s).
• 1/2"/13mm Sheet Metal Screws
• Chimney: Existing 6˝ Code-approved Lined
Masonry Chimney
• or 6˝ Inside Dia. UL 103 HT (US)/ULC-S629 (CDN)
listed manufactured chimney.
• Furnace Cement (manufacturer recommends
Rutland Code 78
CAUTION: Stove is heavy. Make sure you have adequate help and use proper lifting techniques whenever
Uncrate the stove and remove all packing materials and protective
poly bag. NOTICE: DO NOT remove the ceramic blanket material from
inside the stove pipe opening. This blanket provides an air seal on the
side walls of the stove to direct combustion gasses over the secondary
combustion tubes before exiting via the chimney. DO NOT REMOVE
the ceramic blanket or your stove will not operate properly.
Remove all parts from inside the stove. NOTE: Stove may be lightened
during installation by removing fire brick. Replace fire brick before
using. There are six different sizes brick. Note the location of each while
removing for proper location inside firebox.
Before attaching the stove to the base the ash hole will need to be
covered as shown in the following instructions:
1. After the fire brick have been removed place
the flattened carton on the floor and carefully
lay the stove on it's back. Locate the ash hole,
it is located inside the stove at the center of the
firebox as shown. Assemble the ash hole cover in
the following order:
a. Ash Hole Cover Assembly
b. Agitator Bracket Gasket
c. Washer
ASSEMBLY INSTRUCTIONS
Materials
• Pencil
• 6 foot Folding Rule or Tape Measure
• Tin Snips
• Drill: Hand or Electric
• 1/8" dia. Drill Bit (for sheet metal screws)
• Screwdrivers (blade and Phillips type)
• 9/16" Nut Driver or Ratchet with 9/16" Socket
• Safety Glasses
• Gloves
moving stove.
2. On the bottom of the stove use the provided ash
hole cover and 1/4-20 kep nut to secure the ash
hole plug into place as shown.
3. Screw the provided eight (8) 1/4-20 X 1.5 set screws
into the threaded holes as shown. Use an allen
wrench to completely tighten all of the set screw
at each of the four corners.
-4-
• Screwdrivers (blade and Phillips type)
• 9/16" Nut Driver or Ratchet with 9/16" Socket
• Safety Glasses
• Gloves
materials
(NOTE: The following items are NOT included with
your stove and are required for proper installation.)
Flooring Protection as specified (see page 6)
Chimney Connection: 6"/152mm dia. minimum 24 MSG black or
26 MSG blue steel straight stove pipe or elbow(s).
1/2"/13mm Sheet Metal Screws
Chimney: Existing 6˝ Code-approved Lined Masonry Chimney
Tools
or 6˝ Inside Dia. UL 103 HT (US)/ULC-S629 (CDN) listed
manufactured chimney.
Furnace Cement (manufacturer recommends Rutland Code 78
CAUTION: STOVE IS HEAVY. MAKE SURE YOU
HAVE ADEQUATE HELP AND USE PROPER
LIFTING TECHNIQUES WHENEVER MOVING
STOVE.
1. Uncrate the stove and remove all packing materials
and protective poly bag.
NOTICE: DO NOT remove ceramic blanket
material from inside stove pipe opening (Fig. 1).
This blanket provides an air seal on the side walls
of the stove to direct combustion gasses over the
secondary combustion tubes before exiting via the
chimney. DO NOT REMOVE the ceramic blanket
or your stove will not operate properly.
DO NOT
REMOVE!
Figure 1 – DO NOT remove ceramic blanket from
inside stove pipe opening. This is NOT packing
material but an integral component of the stove
combustion system.
2. Remove all parts from inside stove. NOTE: Stove
may be lightened during installation by removing
fire brick. Replace firebrick & ash cover before us-
TR001B | 20120125.1
3. Pla
car
and
on i
4. Rem
9/16
t h e
stud
eac
5. Plac
posi
step
6. Nex
thre
fig.
sho
7. Car
OP
(
1. Atta
(fig.
defl
NOT
ram
tione
flect
blow
four
faste
hea
www.vogelzang.com