Front Panel Controls - Extron electronics AXI 22 AT Setup Manual

C Line Outputs — Use 6-pole 3.5 mm captive screw connectors to connect two balanced or unbalanced mono line level
devices (AXI 22 AT) or four balanced or unbalanced mono line level devices (AXI 44 AT) (see 3-pole Audio Output Wiring in
figure 5 below).
Balanced or unbalanced stereo devices can also be connected using 6-pole captive screw connectors (see 6-pole Audio
Output Wiring in figure 5 below).
Tip
Ring
Sleeve
Tip
Ring
Sleeve
Balanced Output
6-pole Audio OUTPUT Wiring
Figure 5. Audio Output Wiring
ATTENTION:
For unbalanced audio outputs, connect the sleeves to the ground contact. DO NOT connect the sleeves to
the negative (-) contacts.
ATTENTION :
Pour l'audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les manchons
aux contacts négatifs (–).
D AT (PoE) Port — Insert an Ethernet cable to this RJ-45 port to connect the AXI to a Dante network. This port supports power
over Ethernet (PoE), communication with DSP Configurator for configuration, digital audio transport (AT), and communication
with the Dante network for configuration via Dante Controller.
E
Reset Button — The Reset button returns the AXI to different tiers of default states. When using the reset function, the LED
blinks to indicate the different reset modes. When not using the reset function, the LED operates as a power indicator and
matches the front panel power LED (see the Reset Modes topic in the AXI 22 AT and AXI 44 AT User Guide).

Front Panel Controls

E
CONTROL
GAIN LEVEL
+42
INPUT
+36
+30
1
+24
+18
2
CONFIG +12
+6
0
A C D
B
Power Indicator LED
A
B USB Config Port
Input Selector Button
C
Input Indicator LEDs
D
Input Level and Gain LED Stack
E
Figure 6. AXI 22 AT and AXI 44 AT Front Panel Controls
MIC / LINE INS
POWER
12V
1 2
0.5A MAX
Power Indicator LED — Blinks during boot up and lights steadily when the AXI is operational.
A
USB Config Port — One USB Mini-B port is used for configuration. This port can also be used for firmware updates.
B
Input Selector Button — Press this button to cycle through the AXI inputs. Select an input to adjust gain, set phantom
C
A B
power, and view input levels for that input.
Input Indicator LEDs — These LEDs light to indicate which input is currently selected. Gain and phantom power
D
adjustments only affect the currently selected input.
Tip
NO Ground Here
Sleeve
Tip
NO Ground Here
Sleeve
Unbalanced Output
H I
AXI 22 AT
INPUTS
1 2
CLIP -
+ 48V
1
SIG -
GAIN
ON ON
2 CLIP -
SIG -
OFF OFF
OUTPUTS
F G I
AT (PoE)
OUTPUTS
1 2
R
C D E
Tip
Ring
Sleeve
Balanced Output
3-pole Audio OUTPUT Wiring
E
CONTROL
GAIN LEVEL
+42
INPUT
1
+36
+30
2
+24 GAIN
ON ON
+18
3
CONFIG +12
+6
4
0
OFF OFF
A C D F G
B
Gain Rotary Encoder
F
Phantom Power Switch
G
Phantom Power Indicator LEDs
H
Input and Output Signal and Clip LEDs
I
1 2 1 2
POWER
12V
3 4 3 4
0.6A MAX
A B C
Tip
NO Ground Here
Sleeve
Unbalanced Output
H I
AXI 44 AT
INPUTS
+ 48V
1 2 3 4
1 CLIP -
2 SIG -
3 CLIP -
4
SIG -
OUTPUTS
I
AT (PoE)
R
D E
3