Extron electronics AXI 22 AT D Setup Manual
Decorator-style wallplate
audio expansion interface with dante
Hide thumbs
Also See for AXI 22 AT D:
- User manual (45 pages) ,
- Setup manual (8 pages) ,
- User manual (42 pages)
Advertisement
Quick Links
AXI 22 AT D • Setup Guide
This guide provides basic instructions for an experienced technician to install the AXI 22 AT D Decorator-Style Wallplate
Audio Expansion Interface with Dante. For additional information and specifications, see the AXI 22 AT D product page at
www.extron.com.
Disconnect Power and Mount the AXI 22 AT D
Before beginning installation, disconnect power and turn off all devices that will be connected to the AXI 22 AT D. The AXI 22 AT D
can be installed anywhere microphones or other sources are located. Select a suitable mounting location, then choose an
appropriate mounting option (see the instructions provided with the chosen mounting option).
Rear Panel Connections
C C
AT (PoE)
OUTPUTS
AXI 22 AT D
Rear
Figure 1.
AXI 22 AT D Rear Panel
12 VDC Power Inlet – As an alternative to Power over Ethernet (PoE), the AXI 22 AT D can be powered with an optional
A
12 VDC power supply. Connect the power supply to the rear panel power inlet with a captive screw connector and plug the
power cord into the IEC connector on the power supply (see wiring in figure 2 below). The power LEDs behind the front panel
light steadily while the unit is booting, then turn off when the device is powered and operational. The rear panel AT (PoE) port
activity lights also blink when the unit is operational.
Rear Panel
Power Receptacle
DC Power Cord
Captive Screw
Connector
Ridged
– Return
+12 VDC input
Smooth
Figure 2.
External Power Supply Connection
A A
B B
c c
Top
Ground
all devices.
External
Power Supply
12 VDC, 1 A max.
Product Category
12 VDC Power Inlet
A
Line Outputs
B
AT (PoE) Port
C
1
Advertisement
Related Manuals for Extron electronics AXI 22 AT D
Summary of Contents for Extron electronics AXI 22 AT D
-
Page 1: Rear Panel Connections
Disconnect Power and Mount the AXI 22 AT D Before beginning installation, disconnect power and turn off all devices that will be connected to the AXI 22 AT D. The AXI 22 AT D can be installed anywhere microphones or other sources are located. Select a suitable mounting location, then choose an appropriate mounting option (see the instructions provided with the chosen mounting option). - Page 2 Connect Here AT (PoE) Port — Insert an Ethernet cable into this RJ-45 port to connect the AXI 22 AT D to a Dante network. This port supports Power over Ethernet (PoE), digital audio transport (AT), and communication with the Dante network for configuration...
- Page 3 Power LEDs — These orange LEDs are located behind the front panel and light when power is applied to the unit (visible through the top of the XLR inputs). The LEDs light while the AXI 22 AT D is booting up and turn off when boot-up is complete.
-
Page 4: Creating A Physical Dante Network
Figure 4. Physical Dante Network Diagram Dante Network Setup Use a standard Ethernet cable to connect the AXI 22 AT D to a network via the AT (PoE) port (see figure on page 1) and power the device. Launch the Dante Controller program. -
Page 5: Finding A Dante Device Ip Address
In the Rename Device panel, enter the new name of the device in the text field ( ). Device names follow Domain Name System (DNS) hostname rules (refer to the Dante Controller section of the AXI 22 AT D User Guide for a full list of device name rules). -
Page 6: Dante Operation
The AXI 22 AT D mic/line inputs are Dante transmitters because the analog audio input is converted into digital audio and transmitted onto the Dante network. The AXI 22 AT D line outputs are Dante receivers because they receive digital audio from the Dante network and output that signal as analog audio.