List Of Added Tone-Fx - Roland V-synth GT Supplementary Manual

List of Added Tone-FX

42: Low Boost
Boosts the volume of the lower range, creating powerful
lows.
fig.MFX-04
L in
Low Boost
R in
Low Boost
Parameter Value
Boost
50–125 Hz
Frequency #1
Boost Gain #2 0– +12 dB
WIDE, MID,
Boost Width
NARROW
Low Gain -15– +15 dB
High Gain -15– +15 dB
Level 0–127
43: Super Filter
This is a filter with an extremely sharp slope. The cutoff
frequency can be varied cyclically.
fig.MFX-05
L in
Super Filter
R in
Super Filter
Parameter Value
LPF, BPF, HPF,
Filter Type
NOTCH
Filter Slope -12, -24, -36 dB
Filter
0–127
Cutoff #1
Filter
0–127
Resonance #2
Filter Gain 0– +12 dB
Modulation Sw OFF,ON
6
L out
2-Band EQ
R out
2-Band EQ
Description
Center frequency at which the lower
range will be boosted
Amount by which the lower range will
be boosted
Width of the lower range that will be
boosted
Gain of the low frequency range
Gain of the high frequency range
Output level
L out
R out
Description
Filter type
Frequency range that will pass
through each filter
LPF: frequencies below the cutoff
BPF: frequencies in the region of the
cutoff
HPF: frequencies above the cutoff
NOTCH: frequencies other than the
region of the cutoff
Amount of attenuation per octave
-36 dB: extremely steep
-24 dB: steep
-12 dB: gentle
Cutoff frequency of the filter
Increasing this value will raise the
cutoff frequency.
Filter resonance level
Increasing this value will emphasize
the region near the cutoff frequency.
Amount of boost for the filter output
On/off switch for cyclic change
Parameter Value
TRI, SQR, SIN,
SAW1, SAW2
Modulation Wave
SAW1
0.05–10.00 Hz,
Rate #3
note
Depth 0–127
Attack 0–127
Level 0–127
44: Step Filter
This is a filter whose cutoff frequency can be modulated in
steps. You can specify the pattern by which the cutoff
frequency will change.
fig.MFX-06
L in
Step Filter
R in
Step Filter
Parameter Value
Step 01–16 0–127
0.05–10.00 Hz,
Rate #1
note
Attack 0–127
LPF, BPF, HPF,
Filter Type
NOTCH
Filter Slope -12, -24, -36 dB
Filter
0–127
Resonance #2
Filter Gain 0– +12 dB
Level 0–127
Input Sync Sw OFF, ON
Input Sync
0–127
Threshold
Description
How the cutoff frequency will be
modulated
TRI: triangle wave
SQR: square wave
SIN: sine wave
SAW1: sawtooth wave (upward)
SAW2: sawtooth wave (downward)
SAW2
Rate of modulation
Depth of modulation
Speed at which the cutoff frequency
will change
This is effective if Modulation Wave is
SQR, SAW1, or SAW2.
Output level
L out
R out
Description
Cutoff frequency at each step
Rate of modulation
Speed at which the cutoff frequency
changes between steps
Filter type
Frequency range that will pass
through each filter
LPF: frequencies below the cutoff
BPF: frequencies in the region of the
cutoff
HPF: frequencies above the cutoff
NOTCH: frequencies other than the
region of the cutoff
Amount of attenuation per octave
-12 dB: gentle
-24 dB: steep
-36 dB: extremely steep
Filter resonance level
Increasing this value will emphasize
the region near the cutoff frequency.
Amount of boost for the filter output
Output level
Specifies whether an input note will
cause the sequence to resume from
the first step of the sequence (ON) or
not (OFF)
Volume at which an input note will be
detected