Roland V-synth GT Supplementary Manual page 14

List of Added Tone-FX
62: Cho/Flg->Stereo Delay
(Chorus/Flanger->Stereo Delay)
This effect connects either Chorus or Flanger and Delay in
series.
fig.MFX-30
L
Chorus/
Flanger
R
Parameter Value
Mod Mode (Chorus CHORUS,
/ Flanger) FLANGER
0.05–10.0 Hz,
Mod Rate #1
note
Mod Depth 0–127
Mod Phase 0–180 deg
Mod Pre Delay 0–50.0 ms
Mod Feedback -98– +98%
Xover LowFreq 50–4000 Hz
Xover Low Gain -36–0 dB
Xover HiFreq 2000–20000 Hz
Xover Hi Gain -36–0 dB
Mod Level 0–127
MONO, STEREO,
Mode
ALTERNATE
0–1300 ms
(MONO), 0–650
Delay Time ms (STEREO,
ALTERNATE),
note
L-R Shift 0–650 ms, note
14
2-Band
Delay
EQ
Description
Selects whether to use chorus or
flanger.
Adjusts the speed of modulation for
the chorus or flanger.
Adjusts the depth of modulation for
the chorus or flanger.
Sets how the chorus or flanger sound
is spread.
Adjusts the delay time from the direct
sound until the chorus or flanger
sound is heard.
Adjusts the proportion of the effect
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Attenuates the effect in the range
below the specified frequency.
Specifies how greatly the low range
will be attenuated.
Attenuates the effect in the range
above the specified frequency.
Specifies how greatly the high range
will be attenuated.
Volume of the chorus or flanger sound.
Switches stereo, monaural, or
alternate.
MONO: This is a single-input, dual-
output delay. Stereo sound (left and
right) are mixed before being input.
STEREO: This is a dual-input, dual-
output delay. The delay sound output
features the same stereo placement as
that of the input.
ALTERNATE: The left and right delay
sound output alternately. (Alternate
delay)
Adjusts the delay time from the direct
sound until the delay sound is heard.
Of the left and right delay sounds, the
delay time will be increased for only
one side.
If the L-R order is L→R, the R sound will
be later. In the case of R→L, the L
sound will be later.
When the mode is set to MONO or
ALTERNATE, this setting will be
ignored.
Parameter Value
L-R Order L→R, R→L
Feedback #2 -98– +98%
Low Damp Freq 50–4000 Hz
Low Damp Gain -36–0 dB
Hi Damp Freq 2000–20000 Hz
Hi Damp Gain -36–0 dB
DRY100:0WET–
Balance #3
DRY0:100WET
Ps Low Freq 50–4000 Hz
Ps Low Gain -15– +15 dB
Ps Hi Freq 2000–20000 Hz
Ps Hi Gain -15– +15 dB
Level 0–127
Description
In STEREO or ALTERNATE mode, this
setting determines which of the left or
right sides has the delay sound before
the other
L→R: The left side is expressed first
R→L: The right side is expressed first
In MONO mode, this setting will be
ignored.
Adjusts the proportion of the delay
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Adjusts the frequency below which
sound fed back to the effect will be cut.
The lower range is attenuated earlier
than other ranges (low-damp effect).
Degree of Low Damp
Adjusts the frequency above which
sound fed back to the effect will be cut.
High Damp, by attenuating the higher
frequencies first, makes the delay
sound more natural.
Degree of High Damp
Volume balance between the direct
sound (DRY) and the delay sound
(WET)
Frequency of the low range
Gain of the low range
Frequency of the high range
Gain of the high range
Output level