Omron CS1 Manual page 35

■ Connecting Cables for CX-One Components (e.g. CX-Programmer)
Product name
Applicable
computers
Cables
between
Programming IBM PC/AT or
Device compatible
(computer) computer
and (D-Sub 9-pin)
peripheral
port
Connecting Cables
between Programming
IBM PC/AT or
Device (computer) and
compatible
RS-232C port
computer
(D-Sub 9-pin)
USB-Serial Conversion
Cable (PC driver CD-ROM
included) IBM PC/AT or
compatible
computer
(D-Sub 9-pin)
Conforms to USB 1.1
Specifications.
Specifications
Connection configuration
IBM PC/AT or compatible computer + CS1W-CN226/626 +
Peripheral port of CPU Unit
RS-232C
Peripheral Port
Connecting Cable
Computer
CS1W-CN226/626
(9-pin RS-232C)
The following configuration can be used when using an
RS-232C cable to connect to an IBM PC/AT or compatible
computer.
IBM PC/AT or compatible computer + XW2Z-200S-CV/V or
XW2Z-500S-CV/V + Peripheral port of CPU Unit.
RS-232C Cable
XW2Z-200S-CV/V
XW2Z-500S-CV/V
IBM PC/AT or compatible computer + XW2Z-200S-CV/V or
XW2Z-500S-CV/V + RS-232C port of CPU Unit or Serial
Communications Board/Unit
RS-232C Cable
XW2Z-200S-CV/V (2 m)
Computer
XW2Z-500S-CV/V (5 m)
(9-pin RS-232C)
Note: We recommend the following configuration if the
CX-Programmer is always connected and you want to
avoid switching to the other CPU Unit when an error
occurs.
Active CPU Unit
Terminator ON
+5 V must be supplied to the
NT-AL001 at computer side.
+5V
NT-AL001
RS-232C RS-422A/485
CX-Programmer
IBM PC/AT or compatible computer +
CS1W-CIF31 + CS1W-CN226/626 + Peripheral
port of CPU Unit
USB-Serial Conversion Cable
CS1W-CIF31
Serial Connecting Cable
Computer
CS1W-CN226/626
USB port
XW2Z-200S-CV/500S-CV
XW2Z-200S-V/500S-V
CQM1-CIF02
IBM PC/AT or compatible computer +
CS1W-CIF31 + XW2Z-200S-CV/500S-CV +
CS1W-CN118 + Peripheral port of CPU Unit
IBM PC/AT or compatible computer +
CS1W-CIF31 + XW2Z-200S-V/500S-V +
CS1W-CN118 + Peripheral port of CPU Unit
IBM PC/AT or compatible computer +
CS1W-CIF31 + XW2Z-200S-CV/500S-CV +
CS1W-CN118 + RS-232C port of CPU Unit or
Serial Communications Board/Unit
IBM PC/AT or compatible computer +
CS1W-CIF31 + XW2Z-200S-V/500S-V + RS-232C
port of CPU Unit or Serial Communications Board/
Unit
Programmable Controllers SYSMAC
Cable
length
2 m
Peripheral port
6 m
0.1 m
Peripheral port
CS1W-CN118
2 m
Serial Communications Board's
RS-232C ports
5 m
CPU Unit's built-in
RS-232C port
2 m
Standby CPU Unit
RUN DPL01 DPL STATUS RUN
ACTIVE
ERR/ALM L CPU STATUS ERR/ALM
INH BKUP R ACTIVE INH BKUP
PRPHL COMM CPU STATUS PRPHL COMM
LEFT CPU
SYSMAC SYSMAC
CS1D-CPU67H PROGRAMMABLE CONTROLLER USE PROGRAMMABLE CONTROLLER CS1D-CPU67H
NO USE
RIGHT CPU
MCPWR BUSY USE MCPWR BUSY
NO USE
OPEN OPEN
DPL SW
ON SPL OFF DPL
ACT. ACT.
ON LEFT RIGHT
PERIPHERAL PERIPHERAL
INIT.
SW
PRPHL
A39512 COMM
RSV
PORT ON PORT
DUPLEX
RS-422A Adapter 5 m
CJ1W-CIF11
RS-422A/485
or NT-AL001
Peripheral port or
RS-232C port
The USB
Serial
Conversion
Cable
connects to
the serial
connecting
cable,
0.5 m
which
connects to
the PLC's
peripheral
port or
RS-232C
port.
Model Standards
Remarks
CS1W-CN226
Can be used
for both
peripheral bus
and host link.
CS1W-CN626
Use when
CE
connecting to
the peripheral
port with a
XW2Z-200S-
CS1W-CN118
CV/V or
XW2Z-500S-
CV/V
RS-232C
Cable.
Can be used
XW2Z-200S-CV
for both
peripheral bus
and host link,
and is
equipped with
an anti-static
XW2Z-500S-CV
connector.
XW2Z-200S-V
Can be used
for host link
only. Cannot
be used for
peripheral
bus.
XW2Z-500S-V
Can be used
for both
peripheral bus
and host link.
Can be used
for both
peripheral bus
and host link.
Can be used
CS1W-CIF31
for host link
only. Cannot
be used for
peripheral
bus.
Can be used
for both
peripheral bus
and host link.
Can be used
for host link
only. Cannot
be used for
peripheral
bus.
CS1G/H
---
N
23