Sony HCD-M333 Service Manual page 45

QQ
3 7 63 1515 0
14. Error Rate Check
14-1. CD Error Rate Check
Procedure:
1. Load the check disc (TDYS-1).
2. Press the . "R" or
MODE" (C36).
3. Press the ENTER/YES "R" button and display "CPLAY2
MID".
4. The display changes to "C =
5. Check that the C error rate is below 20.
6. Press the MENU/NO "R" button to stop playback, then press
the Z (MD) button and take out the check disc.
14-2. MO Error Rate Check
Procedure:
1. Load the continuously-recorded disc. (Refer to "5. USING
THE CONTINUOUSLY RECORDED DISC" (See page 39))
2. Press the . "R" or
MODE" (C36).
3. Press the ENTER/YES "R" button to display "CPLAY2MID".
4. The display changes to "C =
5. If the C error rate is below 20, check that ADER is 00.
6. Press the MENU/NO "R" button to stop playback, then press
the Z (MD) button and take out the disc.
15. Focus Bias Check
Change the focus bias and check the focus tolerance amount.
Procedure:
1. Load the continuously-recorded disc. (Refer to "5. USING
THE CONTINUOUSLY RECORDED DISC" (See page 39))
2. Press the . "R" or
TE
L 13942296513
MODE" (C36).
3. Press the ENTER/YES "R" button to display "CPLAY2 MID".
4. Press the MENU/NO "R" button when "C =
)" is displayed.
5. Press the "R" or
.
CHECK" (C16).
6. Press the ENTER/YES "R" button to display "
".
The first four digits indicate the C error rate, the two digits after
"/ " indicate ADER, and the 2 digits after "c =" indicate the
focus bias value.
7. Press the ENTER/YES "R" button and display "
= ".
Check that the C error is below 220 and ADER is below 2.
8. Press the ENTER/YES "R" button and display "
= ".
Check that the C error is below 220 and ADER is below 2
9. Press the MENU/NO "R" button, then press the Z (MD)
button and take out the disc.
Note: If the C error and ADER are above other than the specified value
at points a (step 8. in the above) or b (step 7. in the above), the
focus bias adjustment may not have been carried out properly.
Adjust perform the beginning again.
www
.
http://www.xiaoyu163.com
> "R" button and display "CPLAY2
AD = )".
> "R" button to display "CPLAY2
AD = )".
> "R" button to display "CPLAY2
"R" button to display "FBIAS
>
x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
16. Auto Gain Control Output Level Adjustment
Be sure to perform this adjustment when the optical pick-up is
replaced.
If the adjustment results becomes "Adjust NG!", the optical pick-
up may be faulty or the servo system circuits may be abnormal.
16-1. CD Auto Gain Control Output Level Adjustment
Procedure:
1. Load the check disc (TDYS-1).
2. Press the m
(CD)" (C11).
3. When the ENTER/YES "R" button is pressed, the adjustment
will be performed automatically.
"Complete!" will then be displayed momentarily when the value
is recorded in the non-volatile memory, after which the display
changes to "AG Set (CD)" (C11).
4. Press the Z (MD) button and take out the check disc.
16-2. MO Auto Gain Control Output Level Adjustment
Procedure:
1. Load the test disc (MDW-74/GA-1).
2. Press the
.
(MO)" (C10).
3. When the ENTER/YES "R" button is pressed, the adjustment
will be performed automatically.
"Complete!" will then be displayed momentarily when the value
is recorded in the non-volatile memory, after which the display
changes to "AG Set (MO)" (C10).
4. Press the Z (MD) button and take out the test disc.
Q Q
3 6 7 1 3 1 5
AD =
/ c =
/ b
/ a
co
.
HCD-M333
9 4 2 8
"R" or > "R" button to display "AG Set
"R" or "R" button to display "AG Set
>
0 5 8 2 9 9 4 2 8
m
9 9
9 9
45