Sony HCD-MG110 Service Manual
Hide thumbs Also See for HCD-MG110:
Table of Contents

Advertisement

HCD-MG110/MG310AV
SERVICE MANUAL
Ver 1.3 2002.05
HCD-MG110/MG310AV are the Amplifier, CD player, Tape
Deck and Tuner section in MHC-MG110/MG310AV.
HC D-MG310AV only
This stereo system is equipped with the Dolby* Pro Logic
Surround decoder.
* Manufactured under license from Dolby Laboratories.
Dolby , Pro Logic , and the double-D symbol ; are
trademarks of Dolby Laboratories. Confidential
unpublished works. '1992-1997 Dolby Laboratories.
All rights reserved.
Amplifier section
U.S.A. models:
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
with 8 ohm loads both channels driven, from
120 – 10,000 Hz; rated 75 watts per channel
minimum RMS power, with no more than 10%
total harmonic distortion from 250 milliwatts to
rated output.
MHC-MG310AV
Front speaker:
Continuous RMS power output
75 + 75 watts
(8 ohms at 1 kHz,
10% THD)
Total harmonic distortion less than 0.09%
(8 ohms at 1 kHz,
40 watts)
Center speaker:
Continuous RMS power output
25 watts
(8 ohms at 1 kHz,
10% THD)
Rear speaker:
Continuous RMS power output
25 + 25 watts
(8 ohms at 1 kHz,
10% THD)
Sony Corporation
9-873-801-14
2002E0500-1
Home Audio Company
C 2002.05
Published by Sony Engineering Corporation
Photo: HCD-MG110
Model Name Using Similar Mechanism
CD Mechanism Type
CD
Section
Base Unit Name
Optical Pick-up Name
Model Name Using Similar Mechanism
TAPE
Section
Tape Transport Mechanism Type

SPECIFICATIONS

MHC-MG110
Continuous RMS power output
75 + 75 watts
(8 ohms at 1 kHz,
10% THD)
Total harmonic distortion less than 0.09%
(8 ohms at 1 kHz,
40 watts)
Inputs
VIDEO/MD IN (phono jacks):
voltage 250 mV/450 mV,
impedance 47 kilohms
5.1CH (MG310AV only):
FRONT (phono jacks):
voltage 450 mV,
impedance 47 kilohms
REAR (phono jacks):
voltage 450 mV,
impedance 47 kilohms
CENTER (phono jack):
voltage 450 mV,
impedance 47 kilohms
SUB WOOFER (phono jack):
voltage 450 mV,
impedance 47 kilohms
Outputs
PHONES (stereo phone jack):
accepts headphones of
8 ohms or more
FRONT SPEAKER:
accepts impedance of 8 to
16 ohms (except for the US,
Cnadian and Mexican model)
SURROUND SPEAKER REAR
(MG310AV only):
accepts impedance of 8 to
16 ohms (except for the US,
Cnadian and Mexican model)
COMPACT DISC DECK RECEIVER
US Model
Canadian Model
HCD-MG110/MG310AV
Mexican Model
HCD-MG110
Australian Model
HCD-MG310AV
NEW
CDM64-K1BD44A
BU-K1BD44A
KSM-213BFN
NEW
CM8L6Z511A
SURROUND SPEAKER SUB WOOFER
(MHC-MG510AV only): accepts impedance of
8 ohms (except for the
North American model)
SUB WOOFER (MHC-MG310AV only):
voltage 1 V,
impedance 1 kilohm
CD player section
System
Compact disc and digital
audio system
Laser
Semiconductor laser
( = 780 nm)
Emission duration:
continuous
Frequency response
2 Hz – 20 kHz (±0.5 dB)
Wavelength
780 – 790 nm
Signal-to-noise ratio
More than 90 dB
Dynamic range
More than 90 dB
OPTICAL OUT (CD)
(Square optical connector jack, rear panel)
Wavelength
660 nm
Output Level
–18 dBm
Tape player section
Recording system
4-track 2-channel stereo
Frequency response
40 – 13,000 Hz (±3 dB),
using Sony TYPE I
cassette
Tuner section
FM stereo, FM/AM superheterodyne tuner
– Continued on next page –

Advertisement

Table of Contents
loading

Summary of Contents for Sony HCD-MG110

  • Page 1: Specifications

    HCD-MG110/MG310AV Mexican Model HCD-MG110 Australian Model HCD-MG310AV HCD-MG110/MG310AV are the Amplifier, CD player, Tape Deck and Tuner section in MHC-MG110/MG310AV. Photo: HCD-MG110 HC D-MG310AV only Model Name Using Similar Mechanism This stereo system is equipped with the Dolby* Pro Logic Surround decoder.
  • Page 2: Table Of Contents

    HCD-MG110/MG310AV Ver 1.3 General FM tuner section Supplied accessories: Remote commander (1) Batteries (2) Tuning range 87.5 – 108.0 MHz Power requirements AM loop antenna (1) Antenna FM lead antenna US, Canadian and Mexican model: FM lead antenna (1) Antenna terminals...
  • Page 3: Leakage Test

    OPERATION. REPLACE THESE COMPONENTS WITH DE FONCTIONNEMENT. NE REMPLACER CES COM- SONY PARTS WHOSE PART NUMBERS APPEAR AS POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY.
  • Page 4: Servicing Note

    HCD-MG110/MG310AV Ver 1.3 SECTION 1 SERVICING NOTES CD-TEXT TEST DISC MODEL IDENTIFICATION This unit is able to display the test data (character information) – REAR VIEW – written in the CD on its fluorescent indicator tube. The CD-TEXT TEST DISC (TGCS-313:4-989-366-01) is used for checking the display.
  • Page 5: General

    HCD-MG110/MG310AV SECTION 2 This section is extracted from instruction manual. GENERAL Parts Identification The items are arranged in alphabetical order. Main unit 56 7 8 2 3 4 w; ql 5.1CH/VIDEO (MD)* 5 PHONES jack wa AUDIO IN L jack wk...
  • Page 6: Setting The Time

    HCD-MG110/MG310AV Setting the time Remote Control Turn on the system. 1 2 3 4 Press TIMER SET. When you set the clock for the first time, go to step 5. Press – . or > + repeatedly to select “CLOCK SET”.
  • Page 7: Disassembly

    HCD-MG110/MG310AV Ver 1.1 SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW 3-2. UPPER COVER (Page 8) 3-3. FRONT BLOCK ASSY (Page 8) 3-13. CASSETTE LID ASSY (A)/(B) 3-4. MAIN BOARD (Page 13) (Page 9) 3-5.
  • Page 8: Upper Cover

    HCD-MG110/MG310AV Ver 1.1 Note: Follow the disassembly procedure in the numerical order given. 3-2. UPPER COVER 2 five screws 3 upper cover (BVTP3 × 8) 2 two screws (BVTP3 × 8) 1 three screws (BVTP3 × 8) 1 three screws (BVTP3 ×...
  • Page 9: Main Board

    HCD-MG110/MG310AV Ver 1.1 3-4. MAIN BOARD MG310AV 3 three screws MG110 (BVTP3 × 10) 3 screw (BVTP3 × 10) 3 screw (BVTP3 × 10) MG310AV 3 three screws (BVTP3 × 10) 1 wire (flat type) (18 core) (CN309) 1 wire (flat type) (21 core)
  • Page 10: Main Amp Board, Power Board

    HCD-MG110/MG310AV 3-6. MAIN AMP BOARD, POWER BOARD 2 four screws (BVTP3 × 8) 1 connector (CN502) 4 three screws 3 MAIN AMP board (BVTP3 × 8) 2 two screws (BVTP3 × 8) 5 center bracket 7 POWER board 6 two screws (BVTP4 ×...
  • Page 11: Mechanism Deck (Cdm64-K1Bd44A)

    HCD-MG110/MG310AV 3-8. CD MECHANISM DECK (CDM64-K1BD44A) 5 CD mechanism deck (CDM64-K1BD44A) 1 screw (2.6 × 8) 2 table (60) 4 two screws (BVTP3 × 8) lower chassis 3 screw (PSW3 × 6) 4 four screws 4 four screws (BVTP3 × 8) (BVTP3 ×...
  • Page 12: Bu Holder Assy

    HCD-MG110/MG310AV 3-10. BU HOLDER ASSY 1 tension spring (F1) 2 tension spring (F-2) 3 two screws (PTP2.6 × 8) 4 BU holder assy 3 two screws (PTP2.6 × 8) 3-11. MOTOR GEAR ASSY (SLED) (M102), CD BOARD 7 gear 8 claw...
  • Page 13: Op Base Assy (Ksm-213Bfn)

    HCD-MG110/MG310AV 3-12. OP BASE ASSY (KSM-213BFN) 3 Remove the optical pick-up (KSM-213BFN) in the direction of arrow B . 2 sled shaft 1 Slide the lever in the direction of arrow A . 3-13. CASSETTE LID ASSY (A) / (B) 1 Open the cassette lid assy (A)/(B).
  • Page 14: Mech Deck (Tape)

    HCD-MG110/MG310AV 3-14. MECH DECK (TAPE) 1 three screws (BVTP3 × 10) qs mech deck (TAPE) 0 two screws (BVTP2.6) qa MD bracket 4 cassette holder assy (A) 2 two screws (BVTP3 × 10) 9 TC board 5 cassette 8 screw (BVTP2.6)
  • Page 15: Test Mode

    HCD-MG110/MG310AV Ver 1.1 SECTION 4 TEST MODE [MC Cold Reset] [CD Service Mode] • The cold reset clears all data including preset data stored in the • This mode can run the CD sled motor optionally. Use this mode, RAM to initial conditions. Execute this mode when returning for instance, when cleaning the optical pick-up.
  • Page 16: Mechanical Adjustments

    HCD-MG110/MG310AV Ver 1.1 SECTION 5 SECTION 6 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS • TAPE MECHANISM DECK SECTION DECK SECTION 0 dB = 0.775 V Precaution 1. Clean the following parts with a denatured alcohol-moistened Precaution swab: 1. Demagnetize the record/playback head with a head demagne-...
  • Page 17 HCD-MG110/MG310AV Ver 1.1 Record/Playback Head Azimuth Adjustment Adjustment Location: Playback Head (Deck A). Record/Playback/Erase Head (Deck B). DECK A DECK B Note: Perform this adjustments for both decks forward Procedure: 1. Mode: Playback (FWD) test tape MAIN AMP board P-4-A100 FRONT SPEAKER terminal (J501) (10 kHz, –...
  • Page 18: Cd Section

    HCD-MG110/MG310AV Ver 1.1 RFDC signal waveform CD SECTION VOLT/DIV: 200 mV TIME/DIV: 500 ns Note: 1. CD Block is basically designed to operate without adjustment. There- fore, check each item in order given. 2. Use PATD-012 disc (4-225-203-01) unless otherwise indicated.
  • Page 19 HCD-MG110/MG310AV Ver 1.1 E-F Balance Check Checking Location: Connection: – CD BOARD (Conductor Side) – oscilloscope CD board TP (TE) TP (VC) – Procedure: Connect an oscilloscpe to test point TP (TE) and TP (VC) on TP (VC) the CD board.
  • Page 20 HCD-MG110/MG310AV MEMO...
  • Page 21: Diagrams

    HCD-MG110/MG310AV SECTION 7 DIAGRAMS 7-1. BLOCK DIAGRAM – CD SERVO Section – FILTER DIGITAL SIGNAL PROCESSOR, DIGITAL FILTER, D/A CONVERTER IC101 (1/2) RF AMP, 56 53 FOCUS/TRACKING ERROR AMP IC103 DETECTOR CD +5V PCMD LRCK INTERFACE C2PO RFAC RFAC RFAC...
  • Page 22: Block Diagram - Tuner/Tape Deck Section

    HCD-MG110/MG310AV 7-2. BLOCK DIAGRAM – TUNER/TAPE DECK Section – TUNER PACK TUNER L-CH (Page 23) FM ANT L-CH FM 75Ω ANT GND R-CH R-CH AM ANT ANT GND TU-CLK (HCD-MG310AV) TU-CE TUNED (HCD-MG310AV) TUNED 5.1CH (Page 23) INPUT SELECT SWITCH...
  • Page 23: Block Diagram - Surround Section

    HCD-MG110/MG310AV 7-3. BLOCK DIAGRAM – SURROUND Section – (HCD-MG310AV) LOW-PASS FILTER IC304 (1/2) SPE ANA (Page 25) (HCD-MG110) R-CH DOLBY PRO LOGIC SURROUND PROCESSOR R-CH IC301 L-CH (Page 22) WOOFER SWIN SWVOL J303 TRIMMER, SWVOL OUT SUPER WOOFER VOLUME IC304 (2/2)
  • Page 24: Block Diagram - Amp Section

    HCD-MG110/MG310AV Ver 1.1 7-4. BLOCK DIAGRAM – AMP Section – J503 PHONE (HCD-MG310AV) J501 (1/2) FRONT L-CH DBFB AMP (Page 23) IC303 POWER AMP – FRONT SPEAKER IC501 IMPEDANCE R-CH USE 8Ω SURROUND – RY501 IC308 MUTING MUTING OVER LOAD...
  • Page 25: Block Diagram - Display/Power Supply Section

    HCD-MG110/MG310AV 7-5. BLOCK DIAGRAM – DISPLAY/POWER SUPPLY Section – (HCD-MG310AV) GRID DRIVE LED DRIVE D703 – 707 Q721 – 723 Q713 – 717 LED DRIVE D708, 736, FL701 Q702 – 705, 718 D781, 782, 791 FLUORESCENT INDICATOR TUBE S701, 741 – 745,...
  • Page 26: Note For Printed Wiring Boards And Schematic Diagrams

    HCD-MG110/MG310AV Ver 1.3 7-6. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS • Circuit Boards Location (In addition to this, the necessary note is printed in each block) Note on Schematic Diagram: Note on Printed Wiring Boards: • All capacitors are in µF unless otherwise noted. pF: µµF •...
  • Page 27 HCD-MG110/MG310AV • IC Block Diagrams IC103 CXA2581N-T4 – CD Board – RW/ROM IC101 CXD3017Q DC OFST RFDCI – – RFDCO ERROR DIGITAL CORRECTOR DIGITAL ASYMMETRY CORRECTOR – RW/ROM VOFST OPERATIONAL LRCK AMPLIFIER ANALOG SWITCH PCMD INTERFACE DEMODULATOR CONVERTER EMPH APC AMP...
  • Page 28: Schematic Diagram - Cd Section

    HCD-MG110/MG310AV Ver 1.1 7-7. SCHEMATIC DIAGRAM – CD Section – • • See page 39 for Waveforms. See page 27 for IC Block Diagrams. (Page 36) • Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : CD PLAY ∗...
  • Page 29: Printed Wiring Board - Cd Section

    HCD-MG110/MG310AV 7-8. PRINTED WIRING BOARD – CD Section – • See page 26 for Circuit Boards Location. OPTICAL PICK-UP BLOCK KSM-213BFN CD BOARD M101 (SPINDLE) S101 (LIMIT) (VC) M102 (SLED) TP (RFAC) TP (FE) MAIN BOARD (RFDC) TP (TE) CN303...
  • Page 30: Printed Wiring Boards - Cd Motor/Sensor Section

    HCD-MG110/MG310AV Ver 1.1 7-9. PRINTED WIRING BOARDS – CD MOTOR/SENSOR Section – • See page 26 for Circuit Boards Location. (Page 38) MAIN BOARD CN305 T SENSOR BOARD L. T MOTOR BOARD 1 2 3 4 5 (LOADING) (TABLE) (11)
  • Page 31: Schematic Diagram - Cd Motor/Sensor Section

    HCD-MG110/MG310AV 7-10. SCHEMATIC DIAGRAM – CD MOTOR/SENSOR Section – (Page 36) (Page 36) (Page 36) (Page 36) (Page 36) • Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : CD...
  • Page 32: Printed Wiring Board - Tc Section

    HCD-MG110/MG310AV 7-11. PRINTED WIRING BOARD – TC Section – • See page 26 for Circuit Boards Location. MAIN BOARD (Page 38) CN311 TC BOARD 1-680-807- (11) HP101 PB HEAD (DECK A) HRPE101 REC/PB/ERASE HEAD (DECK B) • Semiconductor Location Ref. No.
  • Page 33: Schematic Diagram - Tc Section

    HCD-MG110/MG310AV 7-12. SCHEMATIC DIAGRAM – TC Section – • See page 39 for IC Block Diagram. (Page 34) • Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : TAPE PLAY ) : REC...
  • Page 34: Schematic Diagram - Main Section (1/4)

    HCD-MG110/MG310AV Ver 1.1 7-13. SCHEMATIC DIAGRAM – MAIN Section (1/4) – (Page 41) (Page (Page 33) (Page 36) • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM...
  • Page 35: Schematic Diagram - Main Section (2/4)

    HCD-MG110/MG310AV Ver 1.1 7-14. SCHEMATIC DIAGRAM – MAIN Section (2/4) – (Page 43) (Page 34) (Page 47) (Page 41) (Page 36) (Page 37) • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM...
  • Page 36: Schematic Diagram - Main Section (3/4)

    HCD-MG110/MG310AV Ver 1.3 7-15. SCHEMATIC DIAGRAM – MAIN Section (3/4) – • See page 39 for IC Block Diagram. (Page 34) (CS, CND, MX) (Page 35) (Page 43) (Page 28) (Page (Page 31) (Page 31) (Page 31) (Page 31) (Page 31) •...
  • Page 37: Schematic Diagram - Main Section (4/4)

    HCD-MG110/MG310AV Ver 1.3 7-16. SCHEMATIC DIAGRAM – MAIN Section (4/4) – • See page 39 for Waveforms. (Page 35) ∗R816 (MX) 2.2k (US, CND) (US, CND, MX) ∗ (Page 41) (Page 36) • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions.
  • Page 38: Printed Wiring Board - Main Section

    HCD-MG110/MG310AV Ver 1.3 7-17. PRINTED WIRING BOARD – MAIN Section – • See page 26 for Circuit Boards Location. (Page 42) (Page 32) (Page 42) TAPE GAME LINK MECHANISM DECK DISPLAY BOARD TC BOARD BLOCK BOARD CN701 CN401 MAIN BOARD...
  • Page 39 HCD-MG110/MG310AV Ver 1.1 • Waveforms – TC Board – – MAIN Board – – CD Board – IC401 TA8189N 1 IC103 qg (RFAC) (CD Play Mode) 4 IC101 ra (TE) (CD Play Mode) qa IC801 qa (SUBXOUT) METAL TAPE A...
  • Page 40: Printed Wiring Boards - Amp Section

    HCD-MG110/MG310AV Ver 1.3 7-18. PRINTED WIRING BOARDS – AMP Section – • See page 26 for Circuit Boards Location. • Semiconductor Location Ref. No. Location D501 D502 D503 H-11 D504 D507 PHONE D508 D509 D510 E-11 D511 D512 D-11 (Page 38)
  • Page 41: Schematic Diagram - Amp Section

    HCD-MG110/MG310AV Ver 1.1 7-19. SCHEMATIC DIAGRAM – AMP Section – (Page 37) (Page 34) (Page 47) (Page 47) 2200 2200 (Page 35) • Voltages and waveforms are dc with respect to ground The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont...
  • Page 42: Printed Wiring Boards - Display Section

    HCD-MG110/MG310AV Ver 1.3 7-20. PRINTED WIRING BOARDS – DISPLAY Section – • See page 26 for Circuit Boards Location. DISPLAY BOARD FL701 FLUORESCENT INDICATOR TUBE CNP707 X701 D707, S745 SURROUND CNP308 D706, S744 PRO LOGIC D705, S743 FRONT D704, S742...
  • Page 43: Schematic Diagram - Display Section

    HCD-MG110/MG310AV 7-21. SCHEMATIC DIAGRAM – DISPLAY Section – • • See page 39 for Waveform. See page 39 for IC Block Diagram. (Page 36) (Page 35) (Page 45) • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions.
  • Page 44: Printed Wiring Board - Control Section

    HCD-MG110/MG310AV 7-22. PRINTED WIRING BOARD – CONTROL Section – • See page 26 for Circuit Boards Location. CONTROL BOARD TUNER/BAND TAPE A/B 5.1CH/VIDEO (MD) D736, S700 TIMER I / 1 SELECT SURROUND MODE D708, S751 PRESET EQ X PAUSE TIMER SET...
  • Page 45: Schematic Diagram - Control Section

    HCD-MG110/MG310AV 7-23. SCHEMATIC DIAGRAM – CONTROL Section – (Page 43) • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM...
  • Page 46: Printed Wiring Boards - Power Section

    HCD-MG110/MG310AV Ver 1.3 7-24. PRINTED WIRING BOARDS – POWER Section – • See page 26 for Circuit Boards Location. • Semiconductor Location Ref. No. Location (US, CND, MX) D901 POWER BOARD (CHASSIS) D902 D911 D912 D913 D914 (AC IN) Q901...
  • Page 47: Schematic Diagram - Power Section

    HCD-MG110/MG310AV Ver 1.3 7-25. SCHEMATIC DIAGRAM – POWER Section – (Page 41) (Page 41) (US, CND, MX) (US, CND, MX) (Page 35) (US, CND, MX) • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont...
  • Page 48: Ic Pin Function Description

    HCD-MG110/MG310AV 7-26. IC PIN FUNCTION DESCRIPTION • CD BOARD IC101 CXD3017Q (DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, DIGITAL FILTER, D/A CONVERTER) Pin No. Pin Name Description Pin No. Pin Name Description RFDC SQSO Subcode Q data output to the system controller (IC801)
  • Page 49 HCD-MG110/MG310AV Ver 1.1 • MAIN BOARD IC801 M30622MGA-A42FP (SYSTEM CONTROLLER) • MAIN BOARD IC801 M30622MGA-A68FP (SYSTEM CONTROLLER) Pin No. Pin Name Description — Not used (open) LOAD POS Loading motor drive signal (load-out direction) output the motor driver (IC881) LOAD NEG...
  • Page 50 HCD-MG110/MG310AV Pin No. Pin Name Description POWER STBY Standby relay drive signal output terminal “L”: standby, “H”: power on FL RESET Reset signal output to the display controller (IC701) A-MUTE Audio muting on/off control signal output terminal “H”: muting HP-CHK Headphone detection signal input terminal “H”: headphone on...
  • Page 51 HCD-MG110/MG310AV Pin No. Pin Name Description C-SENS Internal status monitor input from the CXD3017Q (IC101) C-DATA Command serial data output to the CXD3017Q (IC101) C-LATCH Command latch pulse output to the CXD3017Q (IC101) C-CLK Command serial data transfer clock signal output to the CXD3017Q (IC101)
  • Page 52 HCD-MG110/MG310AV • DISPLAY BOARD IC701 MB90M407APF-G-104-BND (DISPLAY CONTROLLER) Pin No. Pin Name Description 1 to 10 G4 to G13 Grid drive signal output to the fluorescent indicator tube (FL701) VSS-IO — Ground terminal 12 to 22 S34 to S24 Segment drive signal output to the fluorescent indicator tube (FL701) VDD-FIP —...
  • Page 53 HCD-MG110/MG310AV Pin No. Pin Name Description LED6 LED drive signal output terminal (REAR) (MG310AV only) LED7 LED drive signal output terminal (LINK) (MG310AV only) LED8 LED drive signal output terminal (CD lid illumination) LED9 LED drive signal output terminal (CD)
  • Page 54: Exploded Views

    HCD-MG110/MG310AV Ver 1.3 SECTION 8 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark may have some difference from the original are seldom required for routine service.
  • Page 55: Front Panel Section

    HCD-MG110/MG310AV Ver 1.3 8-2. FRONT PANEL SECTION not supplied not supplied supplied S791 supplied with RV701 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-232-761-01 CD LID (MG310AV) 3-846-312-11 SPACER (E) 4-232-761-21 CD LID (MG110) 4-232-757-01 CATCHER, BRACKET...
  • Page 56: Chassis Section

    HCD-MG110/MG310AV Ver 1.3 8-3. CHASSIS SECTION CDM64-K1BD44A not supplied not supplied not supplied supplied not supplied not supplied The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety.
  • Page 57: Mechanism Deck Section (Cdm64-K1Bd44A)

    HCD-MG110/MG310AV Ver 1.3 8-4. MECHANISM DECK SECTION (CDM64-K1BD44A) BU-K1BD44A not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-680-799-11 D SENSOR (IN) BOARD (US, CND, MX) 4-216-086-01 SPRING (F-2), TENSION 1-680-799-21 D SENSOR (IN) BOARD (AUS) 4-957-577-21 SCREW PTP WH (2.6X8) (DIA.
  • Page 58: Base Unit Section (Bu-K1Bd44A)

    HCD-MG110/MG310AV Ver 1.1 8-5. BASE UNIT SECTION (BU-K1BD44A) not supplied M101 M102 The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité.
  • Page 59: Electrical Parts List

    HCD-MG110/MG310AV Ver 1.3 SECTION 9 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.
  • Page 60 HCD-MG110/MG310AV Ver 1.3 CD LED CONTROL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R108 1-216-827-11 METAL CHIP 3.3K 1/16W < RESISTOR > R109 1-216-857-11 METAL CHIP 1/16W R111 1-216-846-11 METAL CHIP 120K 1/16W R781 1-216-805-11 METAL CHIP...
  • Page 61 HCD-MG110/MG310AV Ver 1.3 CONTROL D SENSOR (IN) D SENSOR (OUT) DISPLAY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark S762 1-762-196-21 SWITCH, TACT (m) C741 1-162-967-11 CERAMIC CHIP 0.0033uF 10% S763 1-762-196-21 SWITCH, TACT (M) S764...
  • Page 62 HCD-MG110/MG310AV Ver 1.3 DISPLAY DOOR LED FUSE GAME LINK Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R703 1-216-821-11 METAL CHIP 1/16W < ROTARY ENCODER > R704 1-216-821-11 METAL CHIP 1/16W R705 1-216-845-11 METAL CHIP 100K...
  • Page 63 HCD-MG110/MG310AV Ver 1.3 L.T MOTOR LOAD SW MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-680-796-11 H/P BOARD (US, CND, MX) C120 1-126-961-11 ELECT 2.2uF 1-680-796-21 H/P BOARD (AUS) (MG310AV) ********** C121 1-126-964-11 ELECT 10uF <...
  • Page 64 HCD-MG110/MG310AV Ver 1.1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C230 1-126-964-11 ELECT 10uF C324 1-115-467-11 CERAMIC CHIP 0.22uF (MG310AV) (MG310AV) C231 1-126-964-11 ELECT 10uF (MG310AV) C325 1-126-963-11 ELECT 4.7uF C233 1-162-927-11 CERAMIC CHIP...
  • Page 65 HCD-MG110/MG310AV Ver 1.1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C361 1-126-934-11 ELECT 220uF C971 1-165-319-11 CERAMIC CHIP 0.1uF C362 1-126-964-11 ELECT 10uF C972 1-165-319-11 CERAMIC CHIP 0.1uF C363 1-107-826-11 CERAMIC CHIP 0.1uF C973...
  • Page 66 HCD-MG110/MG310AV Ver 1.1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark IC904 8-759-646-52 IC KIA7805API Q884 8-729-038-67 TRANSISTOR KRC102S IC905 8-759-646-52 IC KIA7805API Q885 8-759-068-54 TRANSISTOR KRA102S < JACK > Q886 8-729-038-67 TRANSISTOR KRC102S Q887...
  • Page 67 HCD-MG110/MG310AV MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R201 1-216-829-11 METAL CHIP 4.7K 1/16W R318 1-216-851-11 METAL CHIP 330K 1/16W R202 1-216-829-11 METAL CHIP 4.7K 1/16W (MG310AV) R203 1-216-845-11 METAL CHIP 100K 1/16W (MG310AV)
  • Page 68 HCD-MG110/MG310AV Ver 1.3 MAIN MAIN AMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R382 1-216-825-11 METAL CHIP 2.2K 1/16W R882 1-249-382-11 CARBON 1/6W R383 1-216-825-11 METAL CHIP 2.2K 1/16W R883 1-216-833-11 METAL CHIP 1/16W R884...
  • Page 69 HCD-MG110/MG310AV Ver 1.1 MAIN AMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C526 1-162-962-11 CERAMIC CHIP 470PF D513 8-719-991-33 DIODE 1SS133T-77 C527 1-162-962-11 CERAMIC CHIP 470PF D601 8-719-991-33 DIODE 1SS133T-77 (MG310AV) C528 1-126-961-11 ELECT 2.2uF...
  • Page 70 HCD-MG110/MG310AV Ver 1.1 MAIN AMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R508 1-249-417-11 CARBON 1/4W R602 1-216-833-11 METAL CHIP 1/16W R509 1-249-417-11 CARBON 1/4W (MG310AV) 0 R510 1-215-891-11 METAL OXIDE R512 1-216-841-11 METAL CHIP...
  • Page 71 HCD-MG110/MG310AV Ver 1.3 MAIN AMP POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R634 1-216-821-11 METAL CHIP 1/16W < TRANSISTOR > (MG310AV) R635 1-216-841-11 METAL CHIP 1/16W Q901 8-729-036-77 TRANSISTOR KRC107M-AT (MG310AV) R636 1-216-821-11 METAL CHIP 1/16W <...
  • Page 72 HCD-MG110/MG310AV Ver 1.3 T SENSOR Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C430 1-162-964-11 CERAMIC CHIP 0.001uF R425 1-216-841-11 METAL CHIP 1/16W C431 1-162-964-11 CERAMIC CHIP 0.001uF C432 1-130-483-00 MYLAR 0.01uF R426 1-216-845-11 METAL CHIP...
  • Page 73 HCD-MG110/MG310AV Ver 1.1 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark M391 1-763-697-11 DC FAN (MG310AV: AUS) S791 1-692-960-21 SWITCH, PUSH (1 KEY) (CD LID OPEN) ************************************************************ HARDWARE LIST ************** 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S...
  • Page 74: Revision History

    Ver. Date Description of Revision 2001.03 2001.05 • Addition of Canadian model (HCD-MG110/MG310AV) and Australian models (HCD-MG310AV) • Addition of test mode • Addition of electrical adjustments • Ref. No. 82 Shield Plate (MD) is changed to “not supplied” 2001.11 Addition of Ref.

This manual is also suitable for:

Hcd-mg310av

Table of Contents