Sony HCD-M333 Service Manual page 31

QQ
3 7 63 1515 0
Display
AUTO CHECK
Err Display
TEMP ADJUST
LDPWR ADJUST
Iop Write
Iop NV Save
EF MO ADJUST
EF CD ADJUST
FBIAS ADJUST
AG Set (MO)
AG Set (CD)
TEMP CHECK
LDPWR CHECK
EF MO CHECK
EF CD CHECK
FBIAS CHECK
ScurveCHECK
VERIFYMODE
DETRK CHECK
0920 CHECK
Iop Read
TE
L 13942296513
Iop Compare
ADJ CLEAR
INFORMATION
CPLAY 2MODE
CREC 2MODE
• For details of each adjustment mode, refer to "Section 5 Electrical Adjustments".
About "Err Display" (C02), please refer to a page 7 self-diagnostic function.
• If a different mode has been selected by mistake, press the MENU/NO "R" button to release that mode.
• Modes with (×) in the Mark column are not used for servicing and therefore are not described in detail. If these modes are set acciden-
tally, press the MENU/NO "R" button to release the mode immediately.
5-1. Operating the Continuous Playback Mode
1. Entering the continuous playback mode
(1) Set the disc in the unit. (Whichever recordable discs or discs for playback only are available)
(2) Press the . "R" or > "R" button to display "CPLAY 2MODE" (C36).
(3) Press the ENTER/YES "R" button to change the display to "CPLAY2MID".
(4) When access completes, the display changes to "C =
Note: The numbers "
2. Changing the parts to be played back
(1) Press the ENTER/YES "R" button during continuous playback to change the display as below.
"CPLAY 2MID" t "CPLAY 2OUT" t "CPLAY 2IN"
When pressed another time, the parts to be played back can be moved.
(2) When access completes, the display changes to "C =
Note: The numbers "
www
3. Ending the continuous playback mode
(1) Press the MENU/NO "R" button. The display will change to "CPLAY 2MODE" (C36).
(2) Press the Z (MD) button and take out the disc.
Note : The playback start addresses for IN, MID, and OUT are as follows.
.
IN
MID
OUT
http://www.xiaoyu163.com
No.
C01 Automatic self-diagnosis
C02 Error history display, clear
C03 Temperature compensation offset adjustment
C04 Laser power adjustment
C05 Iop data writing
C06 Writes current Iop value in read nonvolatile memory using microprocessor
C07 Traverse (MO) adjustment
C08 Traverse (CD) adjustment
C09 Focus bias adjustment
C10 Auto gain output level adjustment (MO)
C11 Auto gain output level adjustment (CD)
C12 Temperature compensation offset check
C13 Laser power check
C14 Traverse (MO) check
C15 Traverse (CD) check
C16 Focus bias check
C17 S-curve check
C18 Nonvolatile memory check
C19 Detrack check
C25 Most circumference check
C26 Iop data display
C27 Comparison with initial Iop value written in nonvolatile memory
C28 Initialization of nonvolatile memory for adjustment values
C31 Display of microprocessor version, etc.
C36 Continuous playback mode
C37 Continuous recording mode
" on the display show you error rates and ADER.
" on the display show you error rates and ADER.
x ao
y
i
: 40h cluster
: 300h cluster
: 700h cluster
http://www.xiaoyu163.com
8
Details
Q Q
3 6 7 1 3
AD = )".
AD = )".
u163
.
2 9 9 4 2 8
Mark
Check
1 5 0 5 8 2 9 9 4
m
co
HCD-M333
9 9
Group
Service
2 8 9 9
31