Navigating The Setup Page; Chapter 6: Setup Page - Watlow EZ-ZONE PM User Manual

6

Chapter 6: Setup Page

Navigating the Setup Page

To go to the Setup Page from the Home Page, press
both the Up ¿ and Down ¯ keys for six seconds.
[``Ai] will appear in the upper display and [`Set]
will appear in the lower display.
• Press the Up ¿ or Down ¯ key to view available
menus. On the following pages top level menus
are identified with a yellow background color.
• Press the Advance Key
able prompts within a menu.
Note:
Some of these menus and parameters may not appear, depending on the controller's options. See model number information in the
Appendix for more information. If there is only one instance of a menu, no submenus will appear.
[``Ai]
[`Set] Analog Input Menu
[```1] to [```2]
[``Ai] Analog Input
[`SEn] Sensor Type
[`Lin] Linearization
[`rt; L ] RTD Leads
[Unit] Units
[`S; L o] Scale Low
[`S; h i] Scale High
[`r; L o] Range Low
[`r; h i] Range High
[`P; E E] Process Error Enable
[`P; E L] Process Error Low
[``t; C ] Thermistor Curve
[``r; r ] Resistance Range
[`FiL] Filter
[`i; e r] Error Latching
[`dEC] Display Precisiom
[`Lnr]*
[`Set] Linearization Menu
[```1] to [```2]
[`Lnr] Linearization
[``Fn] Function
[Unit] Units
[`ip; 1 ] Input Point 1
[`op; 1 ] Output Point 1
[`ip; 2 ] Input Point 2
[`op; 2 ] Output Point 2
[`ip; 3 ] Input Point 3
[`op; 3 ] Output Point 3
[`ip; 4 ] Input Point 4
[`op; 4 ] Output Point 4
[`ip; 5 ] Input Point 5
[`op; 5 ] Output Point 5
[`ip; 6 ] Input Point 6
[`op; 6 ] Output Point 6
[`ip; 7 ] Input Point 7
[`op; 7 ] Output Point 7
[`ip; 8 ] Input Point 8
* Available with PM4, PM8 and PM9 models only
®
Wa t low EZ-ZO N E P M I n te g r at e d C o n tr o ll e r
to enter and view avail-
[`op; 8 ] Output Point 8
[`ip; 9 ] Input Point 9
[`op; 9 ] Output Point 9
[ip; 1 0] Input Point 10
[op; 1 0] Output Point 10
[``Pu]*
[`Set] Process Value
[```1] to [```2]
[``Pu] Process Value
[``Fn] Function
[P; u nt] Pressure Units
[A; u nt] Altitude Units
[`b; p r] Barometric Pressure
[`FiL] Filter
[`dio]
[`Set] Digital Input/Output Menu
[```5] to [``12]
[`dio] Digital Input/Output
[`dir] Direction
[``Fn] Function
[``Fi] Function Instance
[`o; C t] Control
[`o; t b] Time Base
[`o; L o] Low Power Scale
[`o; h i] High Power Scale
[LiM]
[`Set] Limit Menu
[```1]
[LiM] Limit
[`L; S D] Sides
[`L; h y] Hysteresis
[SP; L h] Set Point Limit High
[SP; L L] Set Point Limit Low
[`l; i t] Limit Integrate
[Loop]
[`Set] Control Loop Menu
[```1] to [```2]
[Loop] Control Loop
[`h; A g] Heat Algorithm
[`C; A g] Cool Algorithm
•
• Press the Up ¿ or Down ¯ key to move through
available menu prompts.
• Press the Infinity Key ˆ to move backwards
through the levels: parameter to submenu; sub-
menu to menu; menu to Home Page.
• Press and hold the Infinity Key ˆ for two seconds
to return to the Home Page.
[otpt]
[`Set] Output Menu
[```1] to [```4]
[otpt] Output
[otpt] Output 1, 3 process
55
•
[`C; C r] Cool Output Curve
[t; t Un] Tru-Tune+ Enable
[t; b nd] Tru-Tune+ Band
[`t; g n] Tru-Tune+ Gain
[t; A gr] Autotune Aggressiveness
[`P; d l] Peltier Delay
[`r; E n] Remote Set Point Enable
[`r; t y] Remote Set Point Type
[`UFA] User Failure Action
[FAiL] Input Error Failure
[MAn] Manual Power
[`L; d E] Open Loop Detect Enable
[`L; d t] Open Loop Detect Time
[`L; d d] Open Loop Detect Deviation
[``rp] Ramp Action
[`r; S C] Ramp Scale
[`r; r t] Ramp Rate
[`L; S P] Low Set Point
[`h; S P] High Set Point
[SP; L o] Set Point Open Limit Low
[SP; h i] Set Point Open Limit High
[``Fn] Function
[``Fi] Function Instance
[`o; C t] Control
[`o; t b] Time Base
[`o; L o] Low Power Scale
[`o; h i] High Power Scale
[`o; t y] Type
[``Fn] Function
[``Fi] Function Instance
[`S; L o] Scale Low
[`S; h i] Scale High
[`r; L o] Range Low
[`r; h i] Range High
[`o; C A] Calibration Offset
Chapter 6 Se tup Pa ge