Table of Contents
Advertisement
PSCAN-D-1D-D2 Division 2 Barcode Reader
Code selection
•
Auto-configuration
•
EAN/UPC family
•
2/5 family
•
Code 39 family
•
Code 128 family
•
Codabar family
•
Code 93
•
MSI
•
Code 11
•
Code 16K
•
Code 49
•
Gs1 databar codes
1. Read the Enter Configuration code ONCE.
2. Read configuration codes from the desired groups.
•
Read the code and follow the procedure given
Default value
u
3. Read the Exit and Save Configuration code ONCE.
Subject to modifications
USA: +1 330 486 0002
Germany: +49 621 776 2222
Code selections may be performed according to two different procedures:
Code selections may be performed according to two different procedures:
-
Auto-configuration, allowing an automatic recognition and selection of the code fami
to be read;
-
Auto-configuration, allowing an automatic recognition and selection of the code fami
to be read;
-
Manual configuration, requiring configuration and selection of each code family to
read.
-
Manual configuration, requiring configuration and selection of each code family to
read.
The following codes do not require reading the Enter and Exit configuration codes.
The following codes do not require reading the Enter and Exit configuration codes.
In auto-configuration mode the reader enters a particular state, during which it rea
recognizes and saves all information received from the decoding of an existing code (with
In auto-configuration mode the reader enters a particular state, during which it rea
exception of MSI, Code 49 and Code 16k code types). In this way, the code families will
recognizes and saves all information received from the decoding of an existing code (with
automatically configured.
exception of MSI, Code 49 and Code 16k code types). In this way, the code families will
It is possible to configure up to 10 code types, whose length is variable and check digit ignor
automatically configured.
If reading different codes belonging to the same family, information about the last code
It is possible to configure up to 10 code types, whose length is variable and check digit ignor
overwrite the information about the previous one.
If reading different codes belonging to the same family, information about the last code
overwrite the information about the previous one.
Follow the given procedure to auto-configure the desired code families:
Follow the given procedure to auto-configure the desired code families:
CAUTION
CAUTION
Read the following code to enter th
Read the following code to enter th
Read an existing code belonging to the code families that you need to configure.
Read an existing code belonging to the code families that you need to configure.
Read the following c
normal functioning:
Read the following c
normal functioning:
If you need to change the configuration, repeat the auto-configuration procedure, follow
manual configuration by setting the parameters for each single code family or read the "Rest
If you need to change the configuration, repeat the auto-configuration procedure, follow
Default" c
manual configuration by setting the parameters for each single code family or read the "Rest
restored.
Default" c
restored.
www.pepperl-fuchs.us
Copyright Pepperl+Fuchs
Singapore: +65 6779 9091
Code selections may be performed according to two different procedures:
•
Auto configuration, allowing an automatic recognition and selection
of the code families to be read;
•
Manual configuration, requiring configuration and selection of each
code family to be read.
Auto configuration
•
The following codes do not require reading the Enter and Exit
configuration codes.
AUTO-CONFIGURATION
In auto configuration mode the reader enters a particular state, during
AUTO-CONFIGURATION
which it reads, recognizes and saves all information received from the
decoding of an existing code (with the exception of MSI, Code 49 and
Code 16k code types). In this way, the code families will be automatically
configured.
It is possible to configure up to 10 code types, whose length is variable
and check digit ignored.
If reading different codes belonging to the same family, information
about the last code will overwrite the information about the previous one.
Follow the given procedure to auto-configure the desired
code families:
If no code is read during the auto-configuration procedure
Warning
If no code is read during the auto-configuration procedure (step
(step 2), the configuration will be empty and therefore the
configuration will be empty and therefore the reader will be unable to read
If no code is read during the auto-configuration procedure (step
reader will be unable to read codes.
codes.
configuration will be empty and therefore the reader will be unable to read
codes.
1. Read the following code to enter the auto-configuration mode:
Ì#+AUTOWÎ
Ì#+AUTOWÎ
2. Read an existing code belonging to the code families that you need
to configure.
ode to save the configuration automatically and return to the read
3. Read the following code to save the configuration automatically
ode to save the configuration automatically and return to the read
and return to the reader's normal functioning:
sav
sav
If you need to change the configuration, repeat the auto-configuration
ode on page 186. Be careful that in the latter case all reader parameters will
procedure, follow the manual configuration by setting the parameters
ode on page 186. Be careful that in the latter case all reader parameters will
for each single code family. Be careful that in the latter case all reader
parameters will be restored.
e auto-configuration
mode:
e auto-configuration
mode:
auto-configuration
auto-configuration
e auto-configuration
Ì$-?Î
e auto-configuration
Ì$-?Î
), the
), the
35
Advertisement
Table of Contents
