Table of Contents
Advertisement
Quick Links
USER MANUAL
EN
Chapter index
1. Preliminary warnings
2. Description and characteristics
2.1 Module description
2.2 General characteristics and features
3. Technical specifications
3.1 Input
3.2 Outputs
3.3 Connections
3.4 Power supply
3.5 Module case
3.6 Environmental conditions
4. Preliminary instructions for use
5. Electrical connections
5.1 Safety measures before use
5.2 USB interface
5.3 Connections
5.4 Power supply
5.5 Universal input
5.6 Analog and relay outpu
6. Configuration
6.1
Input selection Mea
/
6.2 START
and
END
6.3 Output selection
6.4
Configuration
through a PC
6.5 Jumpers position
6.6 LED indications on the frontal panel
7. Purchase order code
8. Module layout
9. Decommissioning and disposal
This document is property of SENECA srl. Duplication and reproduction of it are forbidden (t
Contents of present documentation refers to products and technologies described in it. Though we strive for reach perfection
continually, all technical data contained in this document may be modified or added due to technical and commercial needs.
It's impossible eliminate mismatches and discordances completely. Contents of present documentation is anyhow subjected to
periodical revision. I
f you have any questions
mentioned.
Z109REG2
t /
strobe input
sur
ing scale
setting at will
SENECA s.r.l.
Via Austria, 26 – 35127 – PADOVA – ITALY
Tel. +39.049.8705355 – 8705359 Fax. +39.049.8706287
Internet site:
www.seneca.it
Commercial reference:
don't hesitate to contact our structure or to write us to e-mail addresses as above
Universal converter module
-1
with galvanic insulation
Page
2
2
2
4
4
5
8
8
8
Technical assistance:
sales@seneca.it
MI004202-E
Z Line
support@seneca.it
hough
partial), if not authorized.
ENGLISH 1/16
Advertisement
Table of Contents
Related Manuals for Seneca Z109REG2
Summary of Contents for Seneca Z109REG2
- Page 1 Commercial reference: sales@seneca.it This document is property of SENECA srl. Duplication and reproduction of it are forbidden (t hough partial), if not authorized. Contents of present documentation refers to products and technologies described in it. Though we strive for reach perfection continually, all technical data contained in this document may be modified or added due to technical and commercial needs.
-
Page 2: Preliminary Warnings
Manual is not followed. 2. DESCRI AND CH ARA TERISTIC MODULE DESCRI The Z109REG2 module acquires an universal input signal, converts it to an analog format and send it to an universal isolated output. 2.2 GENERAL CH ARA TERISTIC S AND FEATURES niversal... -
Page 3: Input
INSULATIONS 1500VA STANDARDS The module complies with the following standards: EN61000-6-4 (electromagnetic emission, in industrial environment) I / O EN61000-6-2 (electromagnetic immunity, DIGITAL UNIVERSAL in industrial environment) INPUT ANALOG EN61010-1 (safety) Notes: POWERSUPPLY - Use with copper conductor. - Use in Pollution Degree 2 Environment 1500 VA - Power Supply must be Class 2 1500 VA insulating voltage is among:... -
Page 4: Connections
— induction ovens etc...). 5.2 USB INTERFACE The module has a microUSB connector, you can configure it through APP and/or software. For more information please see www.seneca.it/prod ucts /z109reg2 SENECA SENECA instruments with instruments with microUSB Port microUSB Port through APP... - Page 5 As an alterntive to STROBE input. RELAY output contact normally closed, opened in event of alarm. As an alternative to the relay output. It is optoisolated and enables the current analog output. You can use it to multiplex a PLC input on n Z109REG2. In order to enable this input please see: SETTINGS THROUGH INTERNAL JUMPERS 6.
- Page 6 Note: DIP-switches must be set while the module is powered down, otherwise, the module may be damaged. (*)START and END setted in the memory by a PC or by the programming push-buttons. 1 2 3 4 5 6 7 8 ”...
- Page 7 SW1: INPUT SELECTION SW2: START e END POSITION INPUT POSITION INPUT POSITION START POSITION 1 2 3 4 TYPE 1 2 3 4 TYPE 1 2 3 SCALE n° 4 5 6 SCALE n° z z z z z z z z z z z z z Tc K...
-
Page 8: Power Supply
100 mm 1112 PWR/ FAIL ALARM Z109REG2 Z109REG2 ECOMMISSIONING AND DISPOSAL Disposal of Electrical & Electronic Equipment (Applicable throughout the European Union and other European countries with separate collections programs). This symbol, found on your product or on its packaging, indicates that this product should not be treated as household waste when you wish to dispose of it.
Need help?
Do you have a question about the Z109REG2 and is the answer not in the manual?
Questions and answers