Mechanics Of Programming - Honeywell LYNXR Installation And Setup Gude

Mechanics of Programming

*HQHUDO3URJUDPPLQJ,QIRUPDWLRQ
Programming options are stored in non-removable, electrically erasable, nonvolatile EEROM
memory. The system can be programmed at any time, even at the installer's premises prior to the
actual installation. Simply apply power temporarily to the Control and then program the unit as
desired. There are two programming modes:
•
Data field programming (used for setting various system options)
•
Interactive menu mode programming (used for programming zone information, programming Powerline
Carrier Devices, and for entering transmitter serial numbers)
The system can also be programmed remotely, using an IBM Personal Computer, a modem, and Compass
Downloader for Windows. See the Remote Programming/Control (Downloading) section.
<RX PD\ ILQG LW FRQYHQLHQW WR DGMXVW WKH YROXPH VHWWLQJ EHIRUH HQWHULQJ WKH 3URJUDP 0RGH 7KLV ZLOO DOORZ \RX WR FOHDUO\
1RWH
KHDU WKH IHHGEDFN DQQRXQFHPHQWV RU V\VWHP EHHSV LQ WKH 3URJUDPPLQJ 0RGH RI WKH V\VWHP·V EXLOWLQ VSHDNHU 7R DGMXVW
WKH YROXPH SUHVV )81&7,21  92/80( >@ RU >@ 8SRQ H[LWLQJ WKH 3URJUDP 0RGH WKH V\VWHP ZLOO UHVHW WKH YROXPH WR
WKH GHIDXOW YDOXH PLG OHYHO 

&HUWDLQ IHDWXUHV GLIIHU EHWZHHQ WKH /<1;5/<1;5 DQG WKH /<1;5(1 PRGHOV 9HULI\ WKH VSHFLILF PRGHO EHLQJ
LQVWDOOHG SULRU WR WKH V\VWHP SURJUDPPLQJ
Entering Program Mode - Use one of the following methods to enter Programming Mode:
✳
1. Press both the [ ] and [#] keys at the same time, within 50 seconds after power is applied to the Control or
from exiting Programming mode, OR
2. After power-up, enter the Installer Code (4112) + 800 (This method disabled if Program mode is exited
✳
using 98.) to enter Expert Programming mode or Installer Code (4112) + 888 to enter Voice Prompt
Programming mode.
,I D GLIIHUHQW ,QVWDOOHU &RGH KDV EHHQ SURJUDPPHG XVH WKDW FRGH WR HQWHU WKH 3URJUDPPLQJ PRGH 2QFH \RX KDYH HQWHUHG
1RWH
WKH 3URJUDP PRGH GDWD ILHOG
Programming a Data Field
✳
1. Press [ ] + Field No. (for example,
2. When you have completely programmed a data field, the keypad will "beep" three times and then
automatically display the next data field in sequence. To go to a different field, press [
field number.
3. If the number of digits that will be entered in a data field is less than the maximum number of digits
available (e.g. phone number field), enter the desired data, then press [
4. If a nonexistent field has been entered, the keypad will display "EE". Simply re-enter [
number.
To view a data field without making changes: Enter [#] + Field No. Data will be displayed for that field.
To delete an entry in a field: Enter [
Interactive Mode Programming (✻56, ✻80, ✻81, ✻83, ✻84, ✻85)
✳
] + interactive mode No. (for example, ✻56). The keypad will display the first of a series of prompts.
Press [
A detailed procedure (with displays of prompts) is provided in later sections of this manual.
Interactive Mode
✻ 56 Enhanced Zone Programming Mode
✻80 Device Programming Menu Mode
✻81 Zone List Menu Mode
✻ 83 Enhanced Sequential Mode
✻84 Assign Zone Voice Descriptors
✻85 Record Custom Voice Descriptors
Loading Factory Defaults
To load the factory defaults, enter the Programming mode, press ✻97, then press number 1, 2, 3, or 4 to select
from default tables 1-4 at the back of this manual, or press "0" if you are not selecting a default table.

,I D GHIDXOW WDEOH LV ORDGHG DQ\ GDWD WKDW KDV DOUHDG\ EHHQ SURJUDPPHG LQWR WKH V\VWHP ZLOO EH FKDQJHG DFFRUGLQJ WR
WKH GHIDXOW WDEOH VHOHFWHG
✻96 resets all subscriber account numbers and CSID in preparation for an initial download.
Exiting Program Mode
✻98 inhibits re-entry into the Expert or Voice Prompt Programming modes using the Installer Code.
✻99 allows re-entry into the Expert Program mode using Installer Code (4112) + 800 or into the Voice
Prompt Programming mode using Installer Code (4112) + 888.
$IWHU H[LWLQJ SURJUDP PRGH RU XSRQ SRZHUXS  WKH V\VWHP WDNHV XS WR D PLQXWH WR UHVHW 7R E\SDVV WKH UHVHW GHOD\ SUHVV
1RWH
[#] + [0].
 WKH ILUVW GDWD ILHOG LQ WKH V\VWHP ZLOO EH GLVSOD\HG DQG ERWK NH\SDG /('V ZLOO IODVK
✻
✳
21), followed by the required entry.
✳ ✳
] + Field No. + [
Zone characteristics, report codes, and serial numbers
Powerline Carrier Devices
Zone Lists for powerline carrier activation
5800 Series transmitter serial numbers
Voice descriptors for each zone
Up to 5 custom voice descriptors for zones
–14–
✳
] to advance to the next data field.
]. (Applies only to fields ✻40–✻44, ✻88 and ✻94).
Used to Program
✳
] plus the desired
✳
] plus a valid field