Mechanics Of Programming; General Programming Information; Exiting Program Mode - Honeywell LYNXR Installation And Setup Manual

Mechanics of Programming

General Programming Information

Programming options are stored in non-removable, electrically erasable, nonvolatile EEROM memory.
The system can be programmed at any time, even at the installer's premises prior to the actual
installation. Simply apply power temporarily to the Control and then program the unit as desired.
There are two programming modes:
•
Data field programming (used for setting various system options)
•
Interactive menu mode programming (used for programming zone information, programming Powerline
Carrier Devices, and for entering transmitter serial numbers)
The system can also be programmed remotely, using an IBM Personal Computer, a modem, and Compass
Downloader for Windows. See the Remote Programming/Control (Downloading) section.
Note: You may find it convenient to adjust the volume setting before entering the Program Mode. This will allow you to clearly hear
the feedback announcements or system beeps in the Programming Mode, of the system's built-in speaker. To adjust the
volume, press FUNCTION + VOLUME+ [3] or [6]. Upon exiting the Program Mode, the system will reset the volume to the
default value (mid level).
!
Certain features differ between the LYNXR/LYNXR24 and the LYNXR-EN models. Verify the specific model being
installed prior to the system programming.
Entering Program Mode - Use one of the following methods to enter Programming Mode:
✻
1. Press both the [ ] and [#] keys at the same time, within 50 seconds after power is applied to the Control or
from exiting Programming mode, OR
2. After power-up, enter the Installer Code (4112) + 800 (This method disabled if Program mode is exited using
✻
98.) to enter Expert Programming mode or Installer Code (4112) + 888 to enter Voice Prompt
Programming mode.
Note: If a different Installer Code has been programmed, use that code to enter the Programming mode. Once you have entered the
Program mode, data field
Programming a Data Field
✻
1. Press [ ] + Field No. (for example,
2. When you have completely programmed a data field, the keypad will "beep" three times and then
automatically display the next data field in sequence. To go to a different field, press [
number.
3. If the number of digits that will be entered in a data field is less than the maximum number of digits available
(e.g. phone number field), enter the desired data, then press [
4. If a nonexistent field has been entered, the keypad will display "EE". Simply re-enter [
number.
To view a data field without making changes: Enter [#] + Field No. Data will be displayed for that field.
To delete an entry in a field: Enter [
Interactive Mode Programming (
✻
Press [ ] + interactive mode No. (for example,
A detailed procedure (with displays of prompts) is provided in later sections of this manual.
Interactive Mode
✻
56 Enhanced Zone Programming Mode
✻
80 Device Programming Menu Mode
✻
81 Zone List Menu Mode
✻
83 Enhanced Sequential Mode
✻
84 Assign Zone Voice Descriptors
✻
85 Record Custom Voice Descriptors
Loading Factory Defaults
To load the factory defaults, enter the Programming mode, press
from default tables 1-4 at the back of this manual, or press "0" if you are not selecting a default table.
!
If a default table is loaded, any data that has already been programmed into the system will be changed according to
the default table selected!
✻
96 resets all subscriber account numbers and CSID in preparation for an initial download.

Exiting Program Mode

✻
98 inhibits re-entry into the Expert or Voice Prompt Programming modes using the Installer Code.
✻
99 allows re-entry into the Expert Program mode using Installer Code (4112) + 800 or into the Voice Prompt
Programming mode using Installer Code (4112) + 888.
Note: After exiting program mode (or upon power-up), the system takes up to a minute to reset. To bypass the reset delay, press
[#] + [0].
✻
20 (the first data field in the system) will be displayed and both keypad LEDs will flash.
✻
21), followed by the required entry.
✻
] + Field No. + [
✻ ✻ ✻
56, 80, 81,
✻
WWW.DIYALARMFORUM.COM
WWW.DIYALARMFORUM.COM
✻
] to advance to the next data field.
✻
]. (Applies only to fields
✻ ✻ ✻
83, 84, 85)
56). The keypad will display the first of a series of prompts.
Used to Program
Zone characteristics, report codes, and serial numbers
Powerline Carrier Devices
Zone Lists for powerline carrier activation
5800 Series transmitter serial numbers
Voice descriptors for each zone
Up to 5 custom voice descriptors for zones
✻
97, then press number 1, 2, 3, or 4 to select
–14–
✻
] plus the desired field
✻
] plus a valid field
✻ ✻ ✻ ✻
40– 44, 88 and 94).