Honeywell LYNXR Installation And Setup Gude page 28

✻
56 Enhanced Zone Programming Mode
While in Program mode, press
Refer to the zone assignment table for
The following explains the
available entries for each. The right-most column provides a further explanation of the entries.
<RX PD\ ILQG LW FRQYHQLHQW WR DGMXVW WKH YROXPH VHWWLQJ EHIRUH HQWHULQJ WKH 3URJUDPPLQJ 0RGH 7KLV ZLOO DOORZ \RX WR FOHDUO\ KHDU
1RWH
IHHGEDFN DQQRXQFHPHQWV RU V\VWHP EHHSV
Zone number
   =RQH QXPEHU
 % -
> @ FRQWLQXH
✻
 H[LW =RQH 3URJUDPPLQJ PRGH
Zone type
 
 ]RQH W\SH
E
]W
> @ FRQWLQXH
✻
>@ UHWXUQ WR SUHYLRXV SURPSW
1RWH
Report code
 
(QWHU WKH UHSRUW FRGH IRU WKLV ]RQH
'
UF
> @ FRQWLQXH
✻
>@ UHWXUQ WR SUHYLRXV SURPSW
Input type
 

G
L
VHQGV SHULRGLF FKHFNLQ VLJQDOV IDXOWV
UHVWRUH DQG ORZ EDWWHU\ VLJQDOV
1RWH 5) W\SH WUDQVPLWWHUV PXVW UHPDLQ ZLWKLQ
 85 XQVXSHUYLVHG 5) ² VHQGV VDPH DV
´5)µ W\SH EXW FRQWURO GRHV QRW VXSHUYLVH
WKH FKHFNLQ VLJQDOV
 %5 EXWWRQ W\SH ² VHQGV RQO\ IDXOW DQG ORZ
EDWWHU\ VLJQDOV GRHV QRW VHQG UHVWRUHV RU
FKHFNLQ VLJQDOV
1RWH
> @ FRQWLQXH
✻
>@ UHWXUQ WR SUHYLRXV SURPSW
 
Loop number or Loop and Serial
)
O
number (if using RF Learning)
 ORRS QXPEHU IRU WKH ]RQH RI WKH
  >
> @ FRQWLQXH WR WKH (152// 02'( SURPSW
✻
$ LI QRW HQWHUHG RU 92,&(
'(6&5,3725 SURPSW LI DOUHDG\ HQWHUHG
>@ UHWXUQ WR SUHYLRXV SURPSW
✻
56 to enter Zone Programming Menu Mode.
✻
56 on the separate programming form.
✻
56 prompts in detail. The left two columns identify the prompts and list the
,I  LV DFFHSWHG DV D ]RQH W\SH VDYH WKH 
]RQH W\SH DQG DGYDQFH WR WKH FRQILUP GHOHWH
SURPSW ) 
5) VXSHUYLVHG 5) ²
UDQJH RI WKH UHFHLYHU RWKHUZLVH D
VXSHUYLVLRQ IDLOXUH VLJQDO ZLOO RFFXU
85 DQG %5 W\SH WUDQVPLWWHUV PD\ EH FDUULHG
RII SUHPLVHV RXW RI UDQJH ZLWKRXW FDXVLQJ D
VXSHUYLVLRQ IDLOXUH
WUDQVPLWWHU EHLQJ HQWHUHG
@ FRQWLQXH WR '(/(7( =21(
✻
3$5$0(7(56 &21),50$7,21
SURPSW )
Enter the 2-digit zone number to be programmed and the Voice Descriptor
for the selected zone number will be announced, if it is programmed. Press
✻
[ ] to advance.
•
Zone 01 = hardwire
•
Zones 02-25 = RF zones (only)
•
Zones 26-41 = Button zones (only)
•
Zone 92 = Duress
•
Zones 95, 96, 99 = Panic zones
Pressing 00 exits mode, upon which the prompt "56" blinks, indicating the
mode is inactive. Press [✻] + any field number to go to that field.
Each zone must be assigned to a zone type, which defines the way in
which the system responds to faults in that zone. Enter the 2-digit zone
type for this zone as follows:
00 = Not Used
01 = Entry/Exit #1
02 = Entry/Exit #2
03 = Perimeter
04 = Interior Follower
05 = Trouble Day/Alarm Night
06 = 24 Hr Silent
07 = 24 Hr Audible
The report code consists of 2 hexadecimal digits, each in turn consisting of
2 numerical digits. For example, for a report code of "3C", enter [0][3] for
"3" and [1][2] for "C".
If this is Zone 1, 95, 96 or 99, the system skips to the VOICE
DESCRIPTOR prompt (1C).
Enter the input type for the transmitter assigned to this zone. Refer to the
transmitter's instructions for input types of each transmitter.
Note: Zones 2-25 should be assigned Input Type 3 or 4 . Zones 26-41
should be assigned Input Type 5 only.
This prompt can be used to enroll loop number and serial number
via RF transmission or the loop number can be enrolled manually.
If using the RF Learning Mode, there is no need to manually enter
a loop number. Proceed directly to RF Learning
Notes: (1) BR type devices cannot be enrolled by using UR or RF type.
Likewise, UR or RF type devices cannot be enrolled by using a
BR type device. There is a 52-second time-out for RF
enrolling. At the end of the time-out, the system returns to
the INPUT TYPE prompt (d). If enrolled, loop number and "L"
are displayed.
(2) Once encrypted (high-security) devices have been
enrolled they must be activated. Refer to the device's
Installation Instructions to activate the High-Security
Mode.
–28–
08 = 24 Hr Aux
09 = Fire without verify
10 = Interior w/Delay
20 = Arm–Stay
21 = Arm–Away
22 = Disarm
23 = No Alarm Response
24 = Silent Burglary