Honeywell LYNXR Installation And Setup Gude page 18

Data Field Descriptions
✼
Entry Delay 01
35
 HQWU\ GHOD\ WLPH LQ VHFRQGV
✼
Entry Delay 02
36
 HQWU\ GHOD\ WLPH LQ VHFRQGV
✼
Audible Exit Warning/Quick Exit
37
([LW :DUQLQJ
 QR H[LW ZDUQLQJ
VRXQG
 SURYLGH H[LW
ZDUQLQJ VRXQG
ZKHQ DUPHG $:$<
✼
Confirmation of Arming Ding
38
 QR GLQJ
 FRQILUPDWLRQ GLQJ DIWHU DUPLQJ V\VWHP
 FRQILUPDWLRQ GLQJ DIWHU DUPLQJ IURP 5) EXWWRQ RU
5) NH\SDG RQO\
✼
Power Up In Previous State
39
 DOZD\V SRZHU XS LQ D GLVDUPHG VWDWH
 DVVXPH WKH V\VWHP VWDWXV SULRU WR SRZHUGRZQ
DIALER PROGRAMMING (
✻ ✻ ✻
42: Enter up to the number of digits shown. Enter 0–9, # + 11 for ' * ' ; # + 12 for '#'; # + 13 for a pause
Fields 40, 41,
(2 seconds)
NOTE: Whenever AAV is used, primary (field
disable command. Otherwise, there is the possibility of connection of the third party to LYNX during AAV mode.
✼
PABX Access Code
40
(QWHU XS WR  GLJLWV LI 3$%; LV QHHGHG WR DFFHVV DQ
RXWVLGH OLQH
✼
Primary Phone No.
41
(QWHU XS WR  GLJLWV
✼
Secondary Phone No.
42
(QWHU XS WR  GLJLWV

$OO IRXU GLJLWV RI
✻
VHOHFWHG LQ  RSWLRQ   DOO WHQ GLJLWV RI WKH 6XEVFULEHU $FFRXQW QXPEHU PXVW EH HQWHUHG
Fields ✻43 and ✻44:
Enter [✻] as the fourth digit if a 3-digit account number (for 3+1 dialer reporting format) is used. Enter 0 as the first
digit of a 4-digit account number for Nos. 0000–0999.
Exit field by pressing [✻] if only 3 digits are used. To clear entries from field, press ✻43✻ or ✻44✻. See
CID®) is used.
blank Programming Form for examples of account number entries. If using the paging feature, do not enter a leading 0
in the subscriber account number, and do not use digits A-F anywhere in the number. Some paging systems provide
voice mail capability, which is activated by a leading 0 in the message. Enter digits 0–9; # +11=B; # +12=C; # +13=D; #
+14=E; or # +15=F.
✼
Primary Subs Account No.
43
(QWHU D IRXU RU WHQ GLJLW DFFRXQW QXPEHU
✼
Secondary Subs Account No.
44
(QWHU D IRXU RU WHQ GLJLW DFFRXQW QXPEHU
4XLFN ([LW
 QR TXLFN
H[LW
 DOORZ TXLFN
H[LW
✻ ✻
40– 50)
✻
41) and secondary (field
WKH 6XEVFULEHU $FFRXQW QXPEHU PXVW EH HQWHUHG LQ )LHOGV
The system will wait the time entered before sounding alarm upon entering
if system is not disarmed. UL installations: must be set for a maximum of
45 seconds
The system will wait the time entered before sounding alarm upon
entering. UL installations: must be set for a maximum of 45 seconds
Exit Warning: Sound consists of slow continuous beeps until last 5 seconds,
when it changes to fast beeps. The warning sound will end at the
termination of exit delay.
Quick Exit: If enabled, user can restart the exit delay time after arming in
STAY mode by entering the user code and pressing the STAY key, or by
pressing the STAY key if Quick Arm is enabled. This avoids having the
user disarm then re-arm the system after allowing someone to enter or exit
Confirmation of arming is provided by a 1/2 second external sounder "ding"
that sounds when closing report is sent, or at the end of exit delay.
If Option 2 is selected the external sounder "ding" occurs immediately after
the system receives the RF transmission.
When the system powers up armed, an alarm will occur 1 minute after
arming if a zone is faulted, and any bypassed zones will be unbypassed.
Note: If the previous state was armed AWAY or STAY, the system will not
respond to sensor changes for 1 minute, which allows time for sensors such
as PIRs to stabilize. UL installations: must be 1 (power up in previous
state)
✻
42) phone numbers should be preceded with the call waiting
If fewer than 6 digits need to be entered, exit by pressing [✻]. To clear
entries from field, press ✻40✻.
If fewer than 20 digits entered, exit by pressing [✻]. To clear entries from
field, press ✻41✻.
Note: Backup reporting (8 attempts are made to the secondary phone
number if no kissoff is received after 8 attempts to the primary
number) is automatic only if there is a secondary phone number
(field ✻42).
If fewer than 24 digits entered, exit by pressing [✻]. To clear entries from
field, press ✻42✻. See backup reporting note for field ✻41. If using the
paging feature, enter the pager phone number here.
Enter [✻] as the fifth digit if a 4-digit account number (for 3+1,
Enter the primary subscriber account number.
To clear entries from field, press ✻43✻.
Enter the secondary subscriber account number.
To clear entries from field, press ✻44✻.
–18–
✻ ✻
 DQG  ,I WHQ GLJLW IRUPDW LV