Enhanced Sequential Mode - Honeywell LYNXR Installation And Setup Gude

By using this mode, you can add, delete, or change the serial number of a transmitter in a zone, but retain
all other existing data that has been programmed for that zone. Note that the ✻83 Enhanced Sequential
mode requires that all zone information must first be entered using the ✻56 Enhanced Zone Programming
mode for all zones below zone number 26 (4 button key area).
Note: Any zone which already has a serial number learned in will not be accessible in ✻83 Enhanced
Sequential mode!
Certain button-type transmitters have more than one button (e.g., 5804). Note that each button must be
assigned to a different zone. Similarly, the 5816 Transmitter has contact terminals and a reed switch for use
with a magnet. If using both, each must also be assigned to a different zone.
This means that the procedures that follow must be repeated for each button-type zone below zone number
26 or contact on the transmitter. Four zone button-type devices are held in zones 26 and above. They will be
started on boundaries of zones 26, 30, 34, and 38. These four zone button-type devices will have the option to
have all information entered in this field. One entry will set the loop number, report code, zone type, and
input device type for all 4 buttons, and a second entry will enter one serial number into four zones.
Note: Use this mode only after all other zone information has been programmed, including transmitter loop
numbers except for button-type zones over zone number 26. The panel will stop at zones 26, 30, 34
and 38 and zone data can be entered as a default here.
Enter Serial Number Sequential mode by pressing ✻83. The prompts for ✻83 are as follows:
A 01 Zone Number ------------------------------------ for entering the zone number to be programmed
1A Enroll Mode -------------------------------------- Selects method of serial number or viewing
1b Enroll Serial Number ------------------------- for entering transmitter serial numbers
F Delete Serial Number------------------------- for deleting existing serial numbers
The following explains these prompts in detail. The left two columns identify the prompts and list the
available entries. The right-most column provides a further explanation of the entries.
 (QWU\ RI D QXPEHU RWKHU WKDQ RQH VSHFLILHG ZLOO JLYH XQSUHGLFWDEOH UHVXOWV
1RWHV
 ,Q (QKDQFHG 6HTXHQWLDO 0RGH  EXWWRQ W\SH NH\V ZLOO DOZD\V EH HQUROOHG VLPXOWDQHRXVO\ 7KH\ ZLOO EH VWRSSHG DW
WKH  EXWWRQ ERXQGDULHV RI    DQG  SURYLGHG WKH ]RQH LV IUHH RI D VHULDO QXPEHU ,I WKH ILUVW ]RQH RI WKH
NH\ KDV D VHULDO QXPEHU HQUROOHG WKH UHPDLQLQJ NH\V FDQQRW EH SURJUDPPHG LQ VHTXHQWLDO PRGH ,Q DGGLWLRQ LI
WKH ]RQH KDV QRW EHHQ VHW XS GXSOLFDWH ORRS PLVVLQJ ]RQH W\SH HWF RQO\ HQWULHV  VNLS WR WKH QH[W ]RQH DQG 
FRS\ WKH NH\ WHPSODWH ZLOO EH DOORZHG
 <RX PD\ ILQG LW FRQYHQLHQW WR DGMXVW
WR FOHDUO\ KHDU IHHGEDFN DQQRXQFHPHQWV RU V\VWHP EHHSV
Zone number
 % -
(QWHU WKH GLJLW ]RQH QXPEHU
✻
> @






✻

83 Enhanced Sequential Mode

WKH YROXPH VHWWLQJ EHIRUH HQWHULQJ WKH 3URJUDPPLQJ 0RGH 7KLV ZLOO DOORZ \RX
FRQWLQXH V\VWHP VHDUFKHV IRU ]RQHV QRW
\HW HQWHUHG IRU ]RQHV  WKURXJK  D ]RQH
W\SH PXVW EH HQWHUHG  WKHQ DGYDQFHV WR
(152// 6(5,$/ 180%(5 SURPSW ´Eµ
H[LW 6HTXHQWLDO PRGH
–35–
Enter the 2-digit zone number of the first transmitter to have its serial
number entered. The system will announce the Voice Descriptor for the
selected zone number, if it is programmed.
Press [✻] to continue. Starting with this zone number, the system will
search for the first transmitter that has all of the following attributes
pre-programmed in ✻56 ENHANCED ZONE PROGRAMMING:
Make sure that the appropriate input type was selected in ✻56 (RF,
a)
UR, or BR programmed)
Make sure that the appropriate loop number was selected in ✻56.
b)
c) No serial number programmed
d) Zone type
If the first zone number entered does not have one or more of the above
attributes, the system will search its database for the first zone that
does, and will display it at the enroll SERIAL NUMBER prompt (1b).
Pressing 00 exits mode, upon which the prompt "83" blinks, indicating
the mode is inactive.
Note: Two exceptions to the requirement above exist for keys. Four zone
button type devices (zone numbers 26, 30, 34, and 38) will be
stopped only if there are no serial numbers enrolled in all 4 zones
of the key, regardless of the attributes that have been entered. In
addition, zone types are not required to be present. In this case,
1A, Option 4 must be selected prior to "Learn".