Table of Contents
Advertisement
Installation Instructions
Mechanics of Programming
To program the system from a keypad:
• You must use a 2-line Alpha display keypad.
• All partitions must be disarmed.
Data Field Programming Procedures
Task
Entering Program Mode
Go to a Data Field
Entering Data
Review a Data Field
Deleting an Entry
Interactive Mode Programming (∗ ∗ ∗ ∗ 56, ∗ ∗ ∗ ∗ 57, ∗ ∗ ∗ ∗ 58, ∗ ∗ ∗ ∗ 79, ∗ ∗ ∗ ∗ 80, ∗ ∗ ∗ ∗ 81, ∗ ∗ ∗ ∗ 82, ∗ ∗ ∗ ∗ 83)
Entering Interactive Mode
Loading Factory Defaults/Initializing for Download
To Load Default Entries
To Initialize Download ID
Do not press
programmed into the system will be changed!
Exiting the Programming Mode
Prevent installer code
reentry
Allow installer code reentry
3-6
Procedure
A) Press both [ ∗ ] and [#] at the same time within 50 seconds after power is applied
to the control, OR
B) After power-up, enter [Installer code (4-1-1-2)] + 8 0 0 (long beep indicates one
of the partitions is armed and system cannot enter program mode).
(method "B" is disabled if you exit the program mode using ∗ 98)
INSTALLER ACCESS NOTE: Some installations may require that the Installer
cannot access the system without the end user's permission (EN50131-1
compliance). Use field *26, entry 2, to select this option. If selected (Installer code
disabled), the system master or partition master must first enable the Installer
code before it can be used. Once enabled, the Installer code remains active until
any other user enters their code.
To enable the Installer code: master code + [#] + 65
Press [ ∗ ] + [Field Number] (for example, ∗ 21).
A display of "EE" or "Entry Error" means you have entered a nonexistent field.
Simply re-enter [ ∗ ] plus a valid field number.
When the desired field number appears, simply enter the digits required. The
keypad beeps three times after the last digit is entered and automatically displays
the next data field in sequence.
If entering less than the maximum digits available (e.g., phone number field),
enter the desired digits, then press [ ∗ ] to end the entry.
Press [#] + [Field Number].
That field's data is displayed, but no changes can be made.
Press [ ∗ ] + [Field No.] + [ ∗ ] (applies only to phone number, account number, and
pager character fields).
Press [ ∗ ] + [Interactive Mode No.] (for example, ∗ 56) while in Program Mode. The
Alpha display keypad will display the first of a series of prompts requesting
entries.
After making the appropriate entry, press the [∗] key to accept the entry and
continue to the next prompt.
Press ∗97 while in Program Mode. This resets all data fields to the default values
shown on the Program Form. Use ∗ 97 only if you wish to return to the original
factory-programmed defaults.
Press ∗96 while in Program Mode. This initializes the system for downloading and
resets all the subscriber account numbers and CSID.
✱
97 to load defaults if any programming has been done previously—data already
Press ∗98. Exits Programming Mode and prevents re-entry by:
Installer Code + [8] + [0] + [0]. To enter the programming mode if ∗ 98 was used to
exit, you must first power the system down. Then power up again, and press [∗]
and [#] at the same time, within 50 seconds of powering up.
Press ∗99. Exits Programming Mode and allows re-entry by:
Installer Code + [ 8] + [0] + [0] or by: Pressing [∗] and [#] at the same time, within
50 seconds of power-up.
Hide quick links:
Advertisement
Table of Contents
