Toshiba HWS-P804XWHM3-E1(TR) Service Manual page 121

Function code table
FC
01 Water heat exchanger capacity *1
02 Cooling/Non-cooling switching
08 Hot Water Boost operation time (operating time)
09 Hot Water Boost set temperature
0A Anti bacteria set temperature
0B Anti bacteria holding time
0C Mixing valve drive time
0F Hot water HP allowance while cooling + hot water
supply
18 Upper limit of cooling set temperature
19 Lower limit of cooling set temperature
1A Upper limit of heating (ZONE1) set temperature
1B Lower limit of heating (ZONE1) set temperature
1C Upper limit of heating (ZONE2) set temperature
1D Lower limit of heating (ZONE2) set temperature
1E Upper limit of hot water set temperature
1F Lower limit of hot water set temperature
20 Hot water HP start temperature
21 Hot water HP stop temperature
22 Priority mode Hot water supply/Heating switching
temperature
23 Boiler output enable switching temperature
24 Outside air temperature for hot water temperature
compensation start
25 Hot water temperature compensation value
26 Night set back change temperature range
27 Set temperature shift with heating Auto
29 Outside air temperature T1 temperature
2B Outside air temperature T3 temperature
2C Set temperature A with outside air temperature of T0
2D Set temperature B with outside air temperature of T1
2E Set temperature C with outside air temperature of 0 °C 0020: 20 °C
2F Set temperature D with outside air temperature of T3
30 Set temperature E with outside air temperature of 20 °C 0020: 20 °C
31 Zone2 ratio with Zone1 as Auto
33 Hydro unit backup heater down time
34 Hydro unit backup heater up time
3A Frost protection function Invalid/Valid
3B Frost protection set temperature
3C 2-way valve operation (logical reverse) control
3E Heating HP/Boiler priority switching when using boiler
40 Activate/deactivate room temperature control
*1 FC_01 is needed for PCB replacement or function code reset procedure has been completed.
*2 System restart with remote controller.
*3 Restart in the mode when stopping.
*4 In addition, it is enable only when switch 2-3 is set to "OFF" and FC61 is set to "3".
AMP Air Conditioning
Item Details
0012: P804XWH**-E1 0015: P1104XWH**-E1 Depends on type
0000: Cooling 0001: Not cooling
0003: 30 min - 0018: 180 min
0040: 40 °C - 0080: 80 °C
0065: 65 °C - 0080: 80 °C
0000: 0 min - 0060: 60 min
0003: 30 sec - 0024: 240 sec
0000: Not allow - 0001: Allow
0018: 18 °C - 0030: 30 °C
0007: 7 °C - 0018: 20 °C
0037: 37 °C - 0060: 60 °C
0020: 20 °C - 0037: 37 °C
0037: 37 °C - 0060: 60 °C
0020: 20 °C - 0037: 37 °C
0060: 60 °C - 0080: 80 °C
0040: 40 °C - 0060: 60 °C
0020: 20 °C - 0045: 45 °C
0040: 40 °C - 0050: 50 °C
-0020: -20 °C - 0020: 20 °C
-0020: -20 °C - 0020: 20 °C
-0020: -20 °C - 0010: 10 °C
0000: 0K - 0015: 15K
0003: 3K - 0020: 20K
-0005: -5K - 0005: 5K
-0015: -15 °C - 0000: 0 °C
0000: 0 °C - 0015: 15 °C
0020: 20 °C - 0060: 60 °C
0020: 20 °C - 0060: 60 °C
- 0060: 60 °C
0020: 20 °C - 0060: 60 °C
- 0060: 60 °C
0000: 0% - 0100: 100%
0000: 5 min 0001: 10 min
0002: 15 min 0003: 20 min
0000: 10 min 0001: 20 min
0002: 30 min 0003: 40 min
0000: Invalid 0001: Valid
0008: 8 °C - 0020: 20 °C
0000: Energised during cooling
0001: Not energised during cooling
0000: Priority on HP 0001: Priority on boiler
0000: Deactivate 0001: Activate
120
www.ampair.co.uk | sales@ampair.co.uk
Factory default
0000: Cooling
0006: 60 min
0075: 75 °C
0075: 75 °C
0030: 30 min
0006: 60 sec
0000: Not allow
0025: 25 °C
0007: 7 °C
0060: 60 °C
0020: 20 °C
0060: 60 °C
0020: 20 °C
0075: 75 °C
0040: 40 °C
0038: 38 °C
0045: 45 °C
0000: 0 °C
-0010: -10 °C
0000: 0 °C
0003: 3K
0005: 5K
0000: 0K
-0010: -10 °C
0010: 10 °C
0040: 40 °C
0035: 35 °C
0030: 30 °C
0025: 25 °C
0020: 20 °C
0080: 80%
0001: 10 min
0000: 10 min
0001: Valid
0015: 15 °C
0000: Activate during
cooling
0000: Priority on HP
0000: Deactivate