Goodman AVPTC42D14 series Installation & Operating Instructions Manual page 17

Speed Selection Dip Switches
Cool Adjust
Selection Selection
Switches Switches
TAP S1 S2 S3
A OFF OFF OFF OFF OFF OFF
B ON OFF ON
C OFF ON OFF
D ON ON ON
Profiles Pre-Run
A -------
B -------
C -------
D 30 sec/50%
To set Airflow: (1) Select model and desired High Stage Cooling
Airflow. Determine the corresponding tap (A, B, C, D). Set dip
switches S1 and S2 to the appropriate ON / OFF positions.
(2) Select model and installed electric heater size. Set dip
switches S9, S10, and S11 to the appropriate ON / OFF positions.
(3) If airflow adjustment is required set Trim Enable Switch
ON (OFF = 0% Trim) and set S3 and S4 to appropriate ON / OFF
positions. Tap A is +5%,Tap B is -5%, Tap C is +10%, Tap D is
-10%.
To Set Comfort mode: Select desired Comfort Mode Profile (see
profiles above). Set dip switches S5 and S6 to appropriate ON /
OFF positions.
Dehumidification: To enable, set dip switch S7 to ON. Cooling
airflow will be reduced to 85% of nominal value during cool call
when Dehum command is present. To disable, set S7 to OFF.
Continuous Fan Speed: Use dip switches S12 and S13 to select
one of 4 continuous fan speeds, Tap A is 25%. Tap B is 50%, Tap
C is 75%, Tap D is 100%.
Notes:
1. Airflow data shown applies to legacy mode operation only.
For a fully communicating system, please see the outdoor
unit's installation instructions for cooling and heat pump
airflow data. See ComfortNet System-Airflow Consideration
section for details.
2. Airflow blink codes are approximations of actual airflow.
HTR kW 9 10 11 AVPTC24B14A AVPTC30C14A AVPTC36C14A AVPTC48C14A AVPTC42D14A† AVPTC48D14A†† AVPTC60D14A†††
3 ON ON ON
5 ON ON OFF
6 ON OFF ON
8 ON OFF OFF
10 OFF ON ON
15 OFF ON OFF
19*
OFF OFF ON
20
21 or 25* OFF OFF OFF
Note: Airflow data shown applies to the electric heat only in either legacy mode or communicating mode operationNR - Not rated* Within thermostat
user menu, CTK0* communicating thermostat will display 20 kW for OFF-OFF-ON dip switch selection and
selection.
† For match up with a 2 ton outdoor unit: Heater kit application shall not exceed 10 kW.
ON-ON-ON.
†† For match up with a 3 ton outdoor unit: Heater kit application shall not exceed 15 kW.
Airflow for 5 kW up to 15 kW heater kits shall be set to 1300 cfm speed tap of ON-OFF-ON.
††† For match up with a 3.5 ton outdoor unit: Heater kit application shall not exceed 20 kW.
Airflow for 5 kW up to 20 kW heater kits shall be set to 1500 cfm speed tap of ON-OFF-OFF
** 3 kW heater kit is not applicable for this indoor application.
Profile
Continuous
Selection
Fan
Switches
Speed
S4 S5 S6 S12 S13
OFF OFF
OFF ON OFF OFF
ON
OFF
ON OFF ON
ON
ON ON ON
ON ON
Short-Run OFF Delay
-------- 60 sec/100%
30 sec/50% 60 sec/100%
7.5 min/82% 60 sec/100%
7.5 min/82% 30 sec/50%
S8
ELECTRIC HEAT AIRFLOW TABLE
550 600
650 700
700 750
800 875
850 950
NR NR
NR NR
NR NR
NR NR
Cooling/Heat Pump Airflow Table
Model
AVPTC24B14**
AVPTC30C14**
AVPTC36C14**
AVPTC48C14**
to
AVPTC42D14**
AVPTC48D14**
AVPTC60D14**
NOTE: Airflow blink codes are approximations of actual airflow. Airflows provided
are at 0.3 static.
NR NR
850 850
900 900
1000 1000
1200 1200
1440 1440
1500 1500
1500 1500
NR NR
Airflow for 5 kW up to 10 kW heater kits shall be set to 850 cfm speed tap of
17
Low stage
Speed tap
(CFM)
A 410
565
B
C 660
765
D
A 440
B 605
C 740
885
D
A 500
B 700
930
C
1120
D
500
A
700
B
930
C
1120
D
560
A
B 765
C 995
1225
D
A 900
B 1035
1140
C
1200
D
A 1210
1365
B
1450
C
1525
D
850** NR
1250 1250
1300 1300
1500 1500
1550 1550
1720 1720
NR NR
1800 1815
NR 1850
21 kW for OFF-OFF-OFF dip switch
High stage
(CFM)
610
835
970
1125
610
835
1020
1225
725
1000
1330
1600
725
1000
1330
1600
800
1090
1420
1750
1350
1550
1700
1800
1610
1815
1920
2025
NR
1250
1300
1500
1550
1780
NR
1850
1850