GE T35 Instruction Manual page 237

5 SETTINGS
Table 5–10: T35 FLEXLOGIC™ OPERANDS (Sheet 4 of 5)
OPERAND TYPE OPERAND SYNTAX
INPUTS/OUTPUTS: Cont Op 1
Contact outputs, Cont Op 2

current
(from detector on
form-A output only)
INPUTS/OUTPUTS: Cont Op 1
Contact outputs, Cont Op 2

voltage
(from detector on
Cont Op 1
form-A output only)
Cont Op 2

INPUTS/OUTPUTS DIRECT INPUT 1 On

Direct inputs
DIRECT INPUT 32 On
INPUTS/OUTPUTS: RemDPS Ip 1 BAD
Remote double- RemDPS Ip 1 INTERM
point status inputs
RemDPS Ip 1 OFF
RemDPS Ip 1 ON
REMDPS Ip 2...
INPUTS/OUTPUTS: REMOTE INPUT 1 On
Remote inputs REMOTE INPUT 2 On
REMOTE INPUT 2 On

REMOTE INPUT 32 On
INPUTS/OUTPUTS: Virt Ip 1
Virtual inputs Virt Ip 2
Virt Ip 3

Virt Ip 64
INPUTS/OUTPUTS: Virt Op 1
Virtual outputs Virt Op 2
Virt Op 3

Virt Op 96
LED INDICATORS: LED IN SERVICE
Fixed front panel LED TROUBLE
LEDs LED TEST MODE
LED TRIP
LED ALARM
LED PICKUP
LED VOLTAGE
LED CURRENT
LED FREQUENCY
LED OTHER
LED PHASE A
LED PHASE B
LED PHASE C
LED NEUTRAL/GROUND
LED INDICATORS: LED TEST IN PROGRESS
LED test
LED INDICATORS: LED USER 1
User-programmable
LED USER 2 to 48
LEDs
PASSWORD ACCESS LOC SETG OFF
SECURITY ACCESS LOC SETG ON
ACCESS LOC CMND OFF
ACCESS LOC CMND ON
ACCESS REM SETG OFF
ACCESS REM SETG ON
ACCESS REM CMND OFF
ACCESS REM CMND ON
UNAUTHORIZED ACCESS
GE Multilin
OPERAND DESCRIPTION
IOn (will not appear unless ordered)
IOn (will not appear unless ordered)

VOn (will not appear unless ordered)
VOn (will not appear unless ordered)

VOff (will not appear unless ordered)
VOff (will not appear unless ordered)

Flag is set, logic=1

Flag is set, logic=1
Asserted while the remote double-point status input is in the bad state.
Asserted while the remote double-point status input is in the intermediate
state.
Asserted while the remote double-point status input is off.
Asserted while the remote double-point status input is on.
Same set of operands as per REMDPS 1 above
Flag is set, logic=1
Flag is set, logic=1
Flag is set, logic=1

Flag is set, logic=1
On Flag is set, logic=1
On Flag is set, logic=1
On Flag is set, logic=1

On Flag is set, logic=1
On Flag is set, logic=1
On Flag is set, logic=1
On Flag is set, logic=1

On Flag is set, logic=1
Asserted when the front panel IN SERVICE LED is on.
Asserted when the front panel TROUBLE LED is on.
Asserted when the front panel TEST MODE LED is on.
Asserted when the front panel TRIP LED is on.
Asserted when the front panel ALARM LED is on.
Asserted when the front panel PICKUP LED is on.
Asserted when the front panel VOLTAGE LED is on.
Asserted when the front panel CURRENT LED is on.
Asserted when the front panel FREQUENCY LED is on.
Asserted when the front panel OTHER LED is on.
Asserted when the front panel PHASE A LED is on.
Asserted when the front panel PHASE B LED is on.
Asserted when the front panel PHASE C LED is on.
Asserted when the front panel NEUTRAL/GROUND LED is on.
An LED test has been initiated and has not finished.
Asserted when user-programmable LED 1 is on.
The operand above is available for user-programmable LEDs 2 through 48.
Asserted when local setting access is disabled.
Asserted when local setting access is enabled.
Asserted when local command access is disabled.
Asserted when local command access is enabled.
Asserted when remote setting access is disabled.
Asserted when remote setting access is enabled.
Asserted when remote command access is disabled.
Asserted when remote command access is enabled.
Asserted when a password entry fails while accessing a password protected
level of the T35.
T35 Transformer Protection System
5.5 FLEXLOGIC™
5
5-103