Subscribe to Our Youtube Channel
Related Manuals for Trikdis E10Tv2
Summary of Contents for Trikdis E10Tv2
-
Page 1: User Manual
Ethernet communicator E10Tv2 USER MANUAL UAB “TRIKDIS” Draugystės str. 17, LT-51229 Kaunas LITHUANIA E-mail: info@trikdis.lt Webpage: www.trikdis.lt... -
Page 2: Table Of Contents
Ethernet communicator E10Tv2 Contents DESCRIPTION ........................... 3 1.1 S ..........................4 AFETY EQUIREMENTS 1.2 T ..........................4 ECHNICAL ARAMETERS 1.3 P ............................ 4 ACKAGE ONTENTS 1.4 C ........................4 OMMUNICATOR STRUCTURE 1.5 T ........................5 ERMINAL BLOCK DESCRIPTION 1.6 L ............................ -
Page 3: Description
Ethernet communicator E10Tv2 Description Ethernet modules E10T are designed to transmit messages from security control panel at a secured object to a monitoring station through internet connection. The module E10T is applied for sending of DTMF tone messages coded in Contact ID protocol of security panel telephone communicator. -
Page 4: Safety Requirements
Ethernet communicator E10Tv2 1.1 Safety Requirements The security alarm system should be installed and maintained by qualified personnel. Prior to installation, please read carefully this manual in order to avoid mistakes that can lead to malfunction or even damage to the equipment. -
Page 5: Terminal Block Description
Ethernet communicator E10Tv2 1.5 Terminal block description Contact Description +12V power supply terminal Common ground terminal T-CP For connecting to the security control panel Tip terminal R-CP For connecting to the security control panel Ring terminal T-TL For connecting a telephone landline... -
Page 6: Configuration And Operation
Ethernet communicator E10Tv2 Configuration and operation Communicator can be configured using TrikdisConfig software via USB cable or remotely. The software is available on www.trikdis.com and operates in MS Windows OS 3.1 Main steps to configure communicator via USB CABLE Download and install TrikdisConfig. -
Page 7: Trikdisconfig Basics
Ethernet communicator E10Tv2 3.3 TrikdisConfig Basics 3.3.1 Main action buttons Action buttons Figure 2. Action buttons Note: if administrator code is set 1) To read the communicator parameters, click Read [F4] and enter as default (123456), it is not the Administrator or Installer code in the pop-up window. In order... -
Page 8: System Settings
• When Use DHCP checkbox is selected, module registration in the network will be done automatically. o If automatic registration is unsuccessful, enter Internal IP address, subnet Mask and Gateway address manually. E10Tv2 supports DNS service; Settings → Access •... -
Page 9: Reporting → Alarm Receiving Centre (Arc) Reporting
Ethernet communicator E10Tv2 3.5 Reporting → Alarm Receiving Centre (ARC) reporting Figure 5. ARC Reporting window Reporting → Primary and backup settings To have connection with Primary and Backup mark checkboxes Enable. Fill in fields for Remote Host, Remote Port. -
Page 10: Event Summary
Ethernet communicator E10Tv2 Event Summary Figure 7. Event Summary window Input description • To describe input fill in fields: Partition, Contact-ID, Zone No.; • (NO, NC, EOL); Select type of input • Enable: report when event occurs (Alarm), report when input line will restore (Restore). -
Page 11: Remote Control
7) Click OK in the prompted window. Remote control Communicator E10Tv2 can be controlled remotely using TrikdisConfig software. To do so, follow steps below: 1) Open TrikdisConfig. 2) At the field Remote access, in the field Unique ID enter the MAC address. MAC address is provided on the product package. -
Page 12: Wiring
Ethernet communicator E10Tv2 Wiring 5.1 Wiring diagram 5.2 Input connection The communicator contains one input terminal (IN1) for connection of sensors. For setting the input connection type and reports on activations refer to chapter 3.7 Event Summary NC, Normally Closed...
Need help?
Do you have a question about the E10Tv2 and is the answer not in the manual?
Questions and answers