Summary of Contents for Ironman Fitness AB Hyper Bench
Page 1
OWNER’S MANUAL AB Hyper Bench 6838.1-081415 6838.1-122215 The specifications of this product may vary from this photo and are subject to change without notice. IRONMAN, IRONMAN TRIATHLON and M-DOT are registered trademarks of World Triathlon Corporation. This product is licensed by the World Triathlon Corporation.
SERVICE IMPORTANT: FOR NORTH AMERICA ONLY For damage or defective product, questions, replacement parts or any other service support, please contact our customer service department (8:00 AM - 5:00 PM Pacific Standard Time, Open Daily) by below methods: For Best Service Email: Service@paradigmhw.com Website: www.paradigmhw.com...
LABEL PLACEMENT UNDER PENALTY OF LAW THIS TAG NOTICE NOT TO BE REMOVED EXCEPT BY THE CONSUMER This article does not meet ALL NEW MATERIALCONSISTING OF POLYURETHANE FOAM PAD_100% requirements of California REGISTRY NO. VA25302 (CN) Bureau of Home Furnish- ings technical bulletin 117.
PRODUCT SAFETY WARNING: Before using this equipment you should consult with your personal physician to see if AB Hyper Bench is appropriate for you. Do not use this equipment without your physician’s approval. Do not use this equipment if you have any of the following conditions or ailments: ...
ASSEMBLY PREPARATION Warning: It is highly recommend that you have assistance during the assembly of this IRONMAN strength equipment. 1. Tools for assembly: General tools needed for the assembly of this IRONMAN strength equipment: Metric Allen Key Set ...
PART LIST Part# Description Q’ty. Part# Description Q’ty. Backrest Support Nylon Nut Tube M10x1.5x10T Rear Support Tube Pin D9.4x70 Ball Knob Handle Grip Tube D50xM16x22xD8 Round Cap Front Support Tube D25.4xD65x31.5 Round Cap Swing Tube D60xD67x43L Backrest Pad Round Cap 900x300x60T D31.8x19L Support Pad ROUND CAP...
STEP 1 1A. Slide Rear Support Tube (B) through the bracket of the Backrest Support Tube (A). Fasten the Rear Support Tube (B) to the Backrest Support Tube (A) using: 1 - (6) Hex Bolt M10x1.5x80L 2 - (51) Flat Washer D20xD11x2T 1 - (75) Nylon Nut M10x1.5x10T 1B.
Page 14
STEP 2 2A. Insert the Rear Support Tube (B) into the bracket of Front Support Tube (D) by aligning the two holes and fasten together using: 2 - (5) Hex Bolt M10x1.5x75L 4 - (51) Flat Washer D20xD11x2T 2 - (75) Nylon Nut M10x1.5x10T Thoroughly tighten the hardware once complete Appearance upon completion of step 2.
Page 16
STEP 3 3A. Fasten the Swing Tube (E) to hole on the underside of Front Support Tube (D) using: 1 - (6) Hex Bolt M10x1.5x80L 2 - (51) Flat Washer D20xD11x2T 1 - (75) Nylon Nut M10x1.5x10T 3B. Align the Swing Tube (E) to the adjustment holes on the front of Front Support Tube (D) and lock the two parts in place Using: 1 - (100) Pin D9.4x70 Thoroughly tighten the hardware once complete...
STEP 4 4A. Insert Handle Grip Tube (C) into the Square shaft of the Front Support Tube (D). Lock the Handle Grip Tube into place using the Ball Knob (102) located on the underside of the Front Support Tube (D). 4B. Mount the Foam Roller (222) with the Foam Rollers Sleeves (223) onto the posts of the Swing Bar (E).
STEP 5 5A. Attach both Support Pads (G) to Handle Grip Tube (C) using: 4 - (3) Hex Bolt M8x1.25x25L 4 - (50) Flat Washer D18xD8.5x1.2T 4 - (54) Spring Washer D15.4xD8.2x2T Note: loosely install all the hardware by hand prior to tightening with tools. This will make aligning the holes easier Thoroughly tighten the hardware once complete Appearance upon completion of step 5.
Page 22
STEP 6 6A. Attach both Backrest Pad (F) to Backrest Support Tube (A) using: 4 - (3) Hex Bolt M8x1.25x25L 4 - (50) Flat Washer D18xD8.5x1.2T 4 - (54) Spring Washer D15.4xD8.2x2T Note: loosely install all the hardware by hand prior to tightening with tools. This will make aligning the holes easier Thoroughly tighten the hardware once complete Appearance upon completion of step 6.
Page 24
DJUSTM ENTS Swing Tu be Adjust tment (Ima age AA-1) Raise or l ower the Swing Tu be (E) into o desired position, align the adjustmen nt holes, a secured it in place w with the Pin n (100) befo fore using t the AB Hy per Bench...
WARRANTY MANUFACTURER’S LIMITED WARRANTY Paradigm Health & Wellness guarantees to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with Paradigm’s Owner’s Manual.
PART REQUEST FORM Paradigm Health & Wellness, Inc. EMAIL THIS FORM WITH YOUR RECIEPT OF PURCHASE TO Service@paradigmhw.com NAME: _______________________________________________________ ADDRESS: ____________________________________________________ CITY ______________ STATE ______________ ZIP ___________________ TELEPHONE: (Day) ____________________________________________ (Night) ____________________________________________ SERIAL#: _____________________________________________________ MODEL#: _____________________________________________________ PURCHASE DATE: _____________________________________________ PLACE OF PURCHASE: _________________________________________ PART # DESCRIPTION “YOUR ORDER WILL BE PROCESSED WITHIN 3 BUSINESS DAYS”...