Table of Contents
Advertisement
20
Mounting of the trim
We recommend that you do not mount the trim, until the insert has
been approved by the chimney sweep, as he may demand to see the
type plate which is situated on the top plate of the cassette (to dis-
mount the top plate, see page 14).
Mount the guide pins of the trim into the locking devices of the cas-
sette.
Scan 1001
NAVN:
MATERIALE:
DIMENSION:
C:\Working Folder\Designs\Scan 1001\91001042.idw
STI:
N/A
16-05-12
GT:
DATO:
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
Fresh air intake
In a well-insulated house, the air used up by the burning process has
to be replaced. This particularly applies to houses with mechanical
ventilation. There are different ways of making sure that an air
exchange takes place. The most important thing is to ensure that
there is a supply of air to the room where the wood stove is located.
The external wall vent must be located as close to the wood stove as
possible, and you must be able to close it when you are not using the
wood stove.
National and local building regulations must be followed with regard
to the connection of fresh-air intake.
Closed combustion system
You should use the closed combustion system for the wood-burning
stove if you live in a newly-built, airtight home. Outside air for com-
bustion is connected through a ventilation pipe via the wall or floor.
It must be possible to shut off the ventilation pipe with a valve, when
the stove is not in use.
N/A
•
Minimum Ø100 mm ventilation pipe, maximum length: 6 m with
16-05-12
DATO:
a maximum of 3 bends.
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
Kantafdækning
EMNE:
AREAL:
Guide pins
91001042
TG.NR:
BC
Locking devices
SIGN:
NAVN:
MATERIALE:
DIMENSION:
C:\Working Folder\Designs\Scan 1001\91001020.idw
STI:
Scan 1001
NAVN:
EMNE:
MATERIALE:
DIMENSION:
C:\Working Folder\Designs\Scan 1001\91001032.idw
STI:
91001042
TG.NR:
BC
SIGN:
C
A S S E M B LY
Mounting of external air supply
To dismount the cover plates for the Ø100 mm sleeve, use an ordinary
screwdriver as shown below. Tilt the screwdriver and loosen the cover
plates.
TG.NR:
Mounting of external air supply on the rear of the cassette
N/A
16-05-12
VÆGT:
DATO:
Mount the Ø100 sleeve.
N/A
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
Scan 1001
EMNE:
Hitch the combustion air box on the rear plate of the cassette. This
Frisklufttilførsel bund af ovn
Scan 1001
NAVN:
box must always be mounted when connecting the insert with exter-
N/A
DATO:
VÆGT:
MATERIALE:
nal air supply
N/A
AREAL:
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
DIMENSION:
C:\Working Folder\Designs\Scan 1001\91001037.idw
STI:
External combustion
air on the bottom of
the cassette
91001042
BC
SIGN:
Kassette
N/A
VÆGT:
N/A
AREAL:
4 x self-tapping screws 4.2 x 6.5 mm
Ekstern forbrænding bag på svøb
91001032
EMNE:
TG.NR:
BC
07-05-2012
SIGN:
N/A
AREAL:
External air
supply on the
rear of the cas-
sette
91001020
TG.NR:
24-04-12
DATO:
SIGN:
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
N/A
15-05-12
VÆGT:
DATO:
Krog Iversen & Co
DK-5492 Vissenbje
Combustion
air box
BC
TG.NR:
S
Advertisement
Table of Contents
