Table of Contents
Advertisement
Section 6
Performance Test Tool Requirement using an
External DIP Switch Box
Figure 6-62 illustrates and list identifies the Tools
and equipment interconnects necessary to perform
the
Performance Tests using an External
iVIZION
Switch Box.
Figure 6-62 Calibration Tool Requirements
d
MOLEX 4-Pin
a
MOLEX 3-Pin
MOLEX 2-Pin
a) iVIZION Unit
b) Power Supply (12V DC - 24V DC)
c) External Switch Box
d) Interface Cable (3380-05-01 EDP#146780)
Figure 6-62 Calibration Tool Requirements
External DIP Switch Performance Test
Procedure Settings
Table 6-2 lists the DIP Switch settings for the
Performance Tests using the External Switch Box.
Table 6-6 Performance Test DIP Switch Settings
Status LED
No. Test Item
Stand-
Operat-
by
Motor
1
Normal
Rotation
Motor
2
Reverse
Rotation
Yellow
Flashes
Stacker
3
Motor
Cyclic
4
Movement
Blue
Lit
Status LED
5
Green
Indication
Banknote
6
Accept-
ance
Exting-
uished
ICB Setting
7
(Reading
Ticket)
*. NOTE: The Sensor ON/OFF Test and the DIP Switch ON/OFF Test
are ONLY available when using the PC procedure!
P/N 960-100929R_Rev. 7 {EDP #148849}
iVIZION® SeriesNext-Generation Banknote Acceptor Unit
(User provided)
DIP Switch Setting (O = ON)
1
2
3
4
5
6
ing
-
O
-
-
-
-
O
O
-
-
-
-
-
-
O
-
-
-
-
-
-
O
-
-
Red
-
-
-
-
O
-
Blue
O
O
O
O
-
-
(Out)
O
-
-
O
-
-
Performance Tests with External Switch
Procedures
Perform the following steps to test the Motor
Normal Forward and Reverse Rotation, the Stacker
Motor, the Cyclic Movement Test, the Status LED
Indication Test, the Banknote Transportation and
the ICB Function Setting Performance Tests.
c
1. Turn the iVIZION Power Switch OFF.
2. Remove the Transport Unit from the Frame.
3. Set the appropriate DIP Switch(es) to "ON" for
the test desired using the 8-Position DIP Switch
b
(Table 6-6).
4. Place the Transport Unit back onto the Frame.
5. Connect the third the fourth Pin Connector of the
External Switch Box Cable to the corresponding
Connector Pins of the five (5) Pin Plug located at
the rear side of the iVIZION Transport Unit
6. Set the External Switch Box Switch to the posi-
tion away from the Status LED on the Box.
7. Turn the iVIZION Power Switch to
iVIZION Status LEDs will indicate Stand-by
Mode when the Status LED on the iVIZION
Lights a steady
on the External Switch blinks at a
8. Turn the External Switch Box Switch toward the
*
iVIZION status LED on the Box. The desired
Test selected by DIP Switch Positions will then
begin (Refer to Table 6-6 "Performance Test DIP
Switch Settings" on page 6-16 of this Section for
each test and its resulting Test indication).
7
8
9. Return the External Switch Box Switch to the
position away from the iVIZION Status LED on
the Box again, and the current Test being run will
-
O
end. If other Switch Box Tests are necessary,
restart from Step 1 at the beginning of this
procedure.
-
O
iVIZION Utility Tools
This portion provides information regarding each
-
O
Service Mode setting procedure.
iVIZION
The following two (2) Tool setting types exist when
using the iVIZION Utility Tools:
-
O
•
CIS Image Views
•
ICB Function Settings.
NOTE: Refer to Figure 6-1 and Figure 6-2
-
O
for the necessary Tools and Harness
Connections and USB Cable Type
Requirements respectively.
ICB/Image Setting Tool Requirements
-
O
NOTE: The ICB Function Status is initially
Factory Set to "INHIBIT" as a standard
function. Therefore, the iVIZION Unit's ICB
must be first initialized using the USB Tool
-
O
Suite Utility Options. Refer to the JCM ICB
Installation Guide for exact programming
descriptions and operational details.
6 - 1 6
Calibration and Testing
Blue
Color, and the Status LED
:
© 2017, JAPAN CASH MACHINE CO., LTD.
. The
ON
Red
Color rate.
Advertisement
Table of Contents
Need help?
Do you have a question about the ivizion ld and is the answer not in the manual?