A Troubleshooting; Introduction; Troubleshooting Overview; Malfunction Led Error Codes - JCM ivizion ld Operation And Maintenance

Next-Generation Banknote Acceptor Unit

A TROUBLESHOOTING

This section provides Troubleshooting instructions
for the iVIZION Series Next-Generation Bank-
®
note Acceptor Unit. This section contains the
following information:
•

Introduction

•

Troubleshooting Overview

•

Malfunction LED Error Codes

•

LED Indication Conditions

•
Error, Jam and Reject Code Tables
•
Maintenance Equipment.
Introduction
Most Banknote Acceptor failures are due to minor
causes. Before replacing any parts, make sure that
all assembly and circuit board connectors are prop-
erly fitted and the harness is properly connected.
Lower than expected Banknote acceptance by the
Validator portion of the iVIZION is often caused
when dust or debris adheres to the Identification
Sensor, or Transport Belt.
Clean the Acceptor section first, then observe the
operating state of the Acceptor in detail when re-
initializing power. This observation is important in
locating any failure causes and the possible fault
area.
If the Acceptor Head has to be repaired by disas-
sembling it, always re-calibrate the Sensors follow-
ing repair.
Symptoms
Normal Condition
Initializing
Downloading
Near Full Detection
Test Mode
Error
Banknote Jam
Reject
ICB
P/N 960-100929R_Rev. 7 {EDP #148849}
iVIZION® Series
A p p e n d i x A

Table A-1 LED Code Condition

Power ON Status
LED LED
Extinguished
(Out)
Blue Flashes
Red Lit
Green Lit
Yellow Lit
Lit Green
Blue Lit
Red Flashes
Yellow Flashes
Green Flashes
Blue Flashes
Perform all repairs by referring to Calibration and
Testing in Section 6 of this manual, and Disassem-
bly/Reassembly in Section 4 of this manual.
Troubleshooting Overview
The iVIZION allows the operator to perform fault
diagnosis by checking various fault Table listings
against the symptom, and survey the cause(s) of
any failure occurrences during the process.
After determining the cause of the failure, repair
the iVIZION Unit by replacing any appropriate
parts, execute the Performance Test to confirm
iVIZION performance, then perform a Sensor re-
adjustment.
Malfunction LED Error Codes
The iVIZION contains two (2) Front Panel Indica-
tors (e.g., a Green Power LED and a Status LED
that exhibits four (4) colors).
The Power LED always lights a Green Color when
power is applied to the iVIZION Unit.
The Status LED lights solid or flashes one combi-
nation of four (4) Colors when errors, Banknote
jams or a reject occurs. The iVIZION Status, Error
Codes, Banknote Jam Codes or Banknote Reject
Codes are indicated by the number and/or Color of
the Status LED solid or flashing light Color condi-
tions.
LED Indication Conditions
Table A-1 lists the Green Power ON LED and the
various Four (4) Color LED Status/Error Code
indications for the iVIZION Unit.
Causes and Solutions
The iVIZION is set-up correctly (Stand-by).
The iVIZION is initializing.
The iVIZION is performing a download.
The iVIZION has detected a Nearly-full Cash Box Condition.
The iVIZION status is in a "Performance Test Mode" (Stand-by).
The iVIZION has an error condition (See Table A-2 LED Error Codes ).
The iVIZION has a jammed Banknote (See Table A-3 Jam LED Flash
Error Codes ).
The iVIZION has a Reject error condition (See Table A-4 Banknote
LED Reject Codes ).
ICB Error Condition (See Table A-2 LED Error Codes ).
© 2017, JAPAN CASH MACHINE CO., LTD.
A - 1