Related Manuals for Digital Projection INSIGHT 4K Quad Series
Summary of Contents for Digital Projection INSIGHT 4K Quad Series
- Page 1 INSIGHT 4K Quad Series INSIGHT 4K Dual LED Series PROTOCOL GUIDE Rev A June 2016 117-930A...
- Page 2 NOTE: this symbol indicates that there is some important information that you should read. Product revision Because we at Digital Projection continually strive to improve our products, we may change specifications and designs, and add new features without prior notice.
- Page 3 Digital Projection Which Products Are Covered In This Document? Notes This document describes the control protocols that can be used with the following projectors: Product Badge • INSIGHT 4K Quad • INSIGHT 4K Dual LED Most commands apply to both INSIGHT projectors; however, exceptions do exist.
-
Page 4: Table Of Contents
Digital Projection CONTENTS Introduction ....................... 1 Network setup ......................Connecting to the projector via a network ................. Connecting to the projector directly with a PC ..............Serial Port setup ......................Protocol commands ....................Examples .......................... Responses ........................Power ........................3 Inputs ........................ -
Page 5: Introduction
Digital Projection INTRODUCTION Introduction Notes The projector can be controlled by using an external control system or a PC via an RS232 or LAN interface, using a terminal-emulation program. For details on connecting the projector to an RS232 or LAN network, or changing network settings, see the user manual. -
Page 6: Protocol Commands
Digital Projection INTRODUCTION Protocol commands Notes Commands are used to simulate menu operations and determine the settings of the projector, and use the following format: • All commands consist of ASCII text strings starting with an asterisk and ending with an ASCII Carriage Return character... -
Page 7: Power
Digital Projection POWER Power Notes power standby.mode commands can assign the values in the table below to both projectors: standby are functionally <command> <operator> <values> equivalent. power normal standby the projector will consume more power in standby standby mode but will start up more quickly. -
Page 8: Inputs
Digital Projection INPUTS Inputs Notes The commands in the table below can be used with both projectors: <command> <operator> <values> input 0 = HDMI A 1 = HDMI B 2 = DisplayPort A 3 = DisplayPort B 4 = Option slot 1 5 = Option slot 2 input.next... -
Page 9: Test Patterns
Digital Projection TEST PATTERNS Test Patterns Notes formatter.pattern command can be used with both projectors: <command> <operator> <value> formatter.pattern 13 = native white formatter.pattern 14 = native black command is used to display 15 = native green formatter test patterns. The patterns... -
Page 10: Lens
Digital Projection LENS Lens Notes The commands in the table below can be used with both projectors: <command> <operator> <value> zoom.in (execute) zoom.out (execute) focus.near (execute) focus.far (execute) lens.center (execute) lens.up 0 - 3 (integer, movement speed: 0 = slowest, 3 = fastest) lens.down... -
Page 11: Image
Digital Projection IMAGE Image Notes The commands in the table below can be used with both projectors: gamma values correspond to <command> <operator> <value> gamma values of 1.0 to 3.0. brightness -50 to 50 (integer) operator always returns a parametric value. -
Page 12: Color
Digital Projection COLOR Color Notes The commands in the table below can be used with both projectors: <command> <operator> <values> mcgd.data tcgd.data mcgd.data green-x, green-y, allow for MCGD data or user TCGD red-x ,red-y, data to be sent as comma separated... - Page 13 Digital Projection COLOR Notes <command> <operator> <values> red.lift -50 to +50 (integer) green.lift brightness -50 to +50 (integer) Adjusting the value red.lift will reset blue.lift -50 to +50 (integer) green.lift blue.lift red.gain -50 to +50 (integer) to zero. green.gain -50 to +50 (integer)
- Page 14 Digital Projection Notes The commands in the table below can be used with both projectors: <command> <operator> <values> 3d.enable On, Off 3d.frmultiplier 1 = x1, 2 = x2, 3 = x3 3d.darktime 0 to 8000, steps of 50 (in µs) 3d.syncoffset...
-
Page 15: Lamps
Digital Projection LAMPS Lamps Notes The commands in the table below can be used with both projectors: <command> <operator> <values> lamp1.hours lamp1.strikes lamp1.serial lamp1.hours command lamp1.status 0 = Off returns the lamp hours in HH:MM 1 = Pre cooling format. - Page 16 Digital Projection LAMPS The commands in the table below can be used with quad lamp projectors: Notes <command> <operator> <values> lamp.mode 0 = all lamps 1 = auto 1 2 = auto 2 3 = auto 3 lamp2.hours lampX.hours commands lamp3.hours...
-
Page 17: Setup
Digital Projection SETUP Setup Notes The commands in the table below can be used with both projectors: <command> <operator> <values> orientation 0 = Desktop Front 1 = Ceiling Front 2 = Desktop Rear 3 = Ceiling Rear shutter on or open off or close ir.address... -
Page 18: Information
Digital Projection INFORMATION Information Notes The commands in the table below can be used with both projectors: <command> <operator> <values> sw.version returns the software sw.version release version. board.id board.id returns the CPU videoboard.id hardware version. fw.version videoboard.id returns the video hardware version. -
Page 19: Insight 4K Series Protocol Guide Rev A June
Digital Projection This page is intentionally left blank. INSIGHT 4K Series Protocol Guide Rev A June 2016 page 15... -
Page 20: Contact Information
Contact Information: Digital Projection Limited Digital Projection Inc. Digital Projection China Digital Projection Asia Greenside Way, Middleton 55 Chastain Road, Suite 115 16 New Industrial Road 中国 北京市 朝阳区 芍药居北里101号 Manchester M24 1XX, UK Kennesaw, GA 30144, USA #02-10 Hudson Technocentre 世奥国际中心A座2006室(100029)