Yamaha F150A Service Manual page 470

Forward gear shim (T2) selection chart
(FL150A) ................................................ A-16
Forward gear shim (T2) selection chart
(FL150B) ................................................ A-17
Fuel control unit and component...............5-16
Fuel diagram .............................................2-14
Fuel filter .....................................................6-7
Fuel hose and blowby hose ........................6-1
Fuel injector ..............................................6-30
Fuel line ......................................................6-5
Fuel pump .................................................6-11
Fuel system......................................1-17, 2-14
Fuel system technical data .......................1-11
Function ......................................................4-2
Fuse box ...................................................7-27
F150A, FL150A, F150B, FL150B................3-5
G.
General feature ...........................................1-1
General periodic maintenance ..................10-8
General tightening torque .........................1-20
Greasing points.......................................10-12
H.
Handling of gas torch ..................................0-2
Handling of gasoline ...................................0-1
Handling of sealant .....................................0-3
Hose routing................................................6-1
Hot part .......................................................0-1
How to use the wiring diagram................... A-1
How to use this manual...............................0-4
I.
Ignition unit................................................. A-4
Ignition unit and component......................5-21
Important reminder on rigging.....................3-1
Installing the balancer assembly...............7-55
Installing the canister ................................6-19
Installing the clamp bracket ......................9-30
Installing the conventional gauge harness 3-12
Installing the cowling lock lever...................9-9
Installing the crankcase cover...................7-60
Installing the cylinder head .......................7-46
Installing the drive shaft ...................8-25, 8-64
Installing the drive sprocket ......................7-17
Installing the driven sprocket and
camshaft .................................................7-36
Installing the exhaust cover ......................7-51
Installing the flushing hose..........................9-8
Installing the flywheel magnet...................7-15
Installing the fuel filter assembly ...............6-10
Installing the fuel injector ..........................6-33
Installing the fuel pump assembly ............ 6-15
Installing the gear pump assembly ........... 9-61
Installing the ignition coil........................... 7-26
Installing the intake manifold .................... 6-40
Installing the isolator lead ......................... 3-14
Installing the lower unit
(L-transom model) ......................... 8-29, 8-64
Installing the lower unit
(X-transom model)......................... 8-30, 8-65
Installing the main wiring harness ............ 3-13
Installing the oil filter bracket ........... 7-56, 7-60
Installing the oil pump assembly...... 7-55, 7-60
Installing the outboard motor ...................... 3-7
Installing the power unit.............................. 7-9
Installing the propeller shaft housing
assembly ....................................... 8-26, 8-64
Installing the PTT motor ........................... 9-53
Installing the PTT switch............................. 9-9
Installing the PTT unit............................... 9-39
Installing the Rectifier Regulator............... 7-26
Installing the reservoir .............................. 9-53
Installing the reverse gear ........................ 8-64
Installing the rigging grommet .................. 3-13
Installing the shift cable .............................. 3-9
Installing the shift rod....................... 8-27, 8-64
Installing the shift rod and shift bracket ...... 9-4
Installing the speed sensor....................... 3-15
Installing the starter motor ............... 5-39, 7-21
Installing the stator assembly ................... 7-14
Installing the steering arm ........................ 9-25
Installing the throttle body assembly ........ 6-26
Installing the throttle cable........................ 3-11
Installing the throttle link ........................... 6-23
Installing the tilt limiter .............................. 3-16
Installing the tilt ram.................................. 9-46
Installing the timing belt ............................ 7-18
Installing the trim ram ............................... 9-46
Installing the upper case........................... 9-15
Installing the vapor separator ................... 6-39
Installing the vapor shut-off valve ............. 6-19
Installing the water pressure sensor......... 3-14
Installing the water pump................. 8-27, 8-64
Installing the wiring harness ..................... 7-31
Installing the 6Y8 Multifunction Meter
harness................................................... 3-12
Installing Y-COP ....................................... 3-20
Intake and exhaust diagram ..................... 2-18
Intake and exhaust system....................... 2-18
Intake manifold and vapor separator ........ 6-34
Intake silencer .......................................... 6-21
J.
Junction box assembly ............................... 5-3
i-4
Index
0
1
2
3
5
6
7
8
9
10
10
A