Assembly: Pro Trac 750 And 950; Clothing; Safety Zone; Starting And Stopping The Engine - Texas Equipment Pro Trac 750 User Manual

Maintenance and storage
The engine shall be stopped when carrying out
maintenance and cleaning operations, when changing
tools and when being transported by means other than
under its own power.
Check regularly that all bolts and nuts are tightened.
Retighten if necessary.
The engine must be completely cooled before storing
indoors or covered.
If the machine unused for a period of time, please refer
to the instructions in this manual.
Maintain or replace safety and instruction labels, as
necessary.
Only use original spare parts or accessories. If not
original parts or accessories is used, the liability is no
longer applied.
Replace faulty silencers.
Miscellaneous
The gears are delivered pre-greased. However, always
ensure they are well greased before each use.
The motor is not pre-filled with oil.
Factory-fitted control devices, such as the handle-
mounted clutch cable, must not be removed or exposed.
Only drain the fuel tank outdoors. Gasoline is extremely
flammable and the fumes are explosive.
Ensure that the machine is properly secured when
transported on a flatbed etc.
Reduce the throttle during engine shutdown and close
the fuel valve.

Assembly: Pro Trac 750 and 950

Please follow the steps in illustrations shown:
(Actual model may vary from the illustration shown.)
1. Box content
A. Engine
B. Brush
C. Rod for angel adjustment of brush
D. Quick release lock for handlebar
E. Direction lever forward - reverse
F. Throttle lever
G. 9 man lever
H. Direction activation lever.
I. Differential lever
J. PTO engager
K. Gear connector rod
L. High adjustment lock
2. Mount accessory ( brush)
Follow the mounting procedure 1-3 as shown in
illustration 2
Fill the motor with oil.
See changing the oil section for more details.

Clothing

When using the machine, wear close-fitting work clothes,
hard-wearing work gloves, ear defenders and non-slip boots
with steel toecaps.

Safety zone

While the machine is being operated and the motor is
running, do not leave the operation zone marked ill6. If it is
necessary to leave the operation zone, for example to attach
an accessory, first stop the engine.

Starting and stopping the engine

Remember: Always check the oil level prior to use!
On engines with dipstick the oil level must always be
between the min. and max. On engines without dipstick the
oil must be visible to the edge on filler hole, when the engine
is horizontal position. Always use SAE-30 oil. Use only
unleaded 95 octane gas. Never over-fill the gas tank.
Warning: Stay out of dashed zone, while starting the engine!
Always start the engine from dotted operation zone See
illustration 6.
Start se ill 3
1. Activate the clutch lever plus the dead man lever
2. Set the throttle lever on max.
3. For gasoline engines
Set the choker on maks. It is not necessary to use
choker on a hot engine see 3-B
For diesel engines
Engage the valve lifter See ill 3-A
4. Pull the start cord to start the motor. Always feed
the start cord back into the motor by hand.
Se Ill 3-D
For models with electrical start, turn the ignition key.
See ill 4-C.
Note: For diesel engines with electrical starter
Engage the valve lifter on key ignition and keep
engaged until steady revolution, then release.
5. When the motor is started, set the choke to
minimum (fully to the right) Engage the throttle
slightly.
Stop
1. Release the dead man lever.
2. Set the throttle control to "low" for models with
electrical start turn the ignition key.
Vibrations may travel up into the handle during
use. We therefore recommend taking a break
every 2 hours.

Operating the machine

Remove all foreign objects from the work area
before using the machine. Stones, glass, branches
and similar items may damage the tiller. Also check
the bolts on the tiller are tightened.
Start the motor as per the instructions below. Stand
clear of the machine's moving parts.
Never attempt to move the machine in any way
other than intended for normal use while the motor
is running.
Drive
Follow the operation procedure as shown in illustration 4:
A-1 Activate gear
A-2 Set throttle
A-3 Choose driving direction (D- R)
A-4 Activate the clutch lever plus the dead man lever
Differential
Activate differential lever see illustration 4C
7