2. Sikkerhedsforeskrifter • Læs denne betjeningsvejledning grundigt, så du forstår og kan følge alle sikkerhedsfo- reskrifter og betjeningsfunktioner fuldstændigt, før du går i gang med at samle og bruge produktet. • Børn må ikke bruge produktet. • Hvis du føler dig syg, træt, eller har indtaget alkohol eller medicin, må du ikke arbejde med maskinen.
4. Opsamling Inden opsamling påbegyndes bør du lægge alle dele frem. Monter et plastic bøs i hver side af de dobbelte knive. Monter et hjulophæng i det midterste hul på aks- len. Bemærk at ringen på hjulophænget skal vende mod den korteste ende på akslen. Spænd helt fast.
Page 6
På den lange side af akslen monteres følgende i korrekt orden. Vær opmærksom på, at bøjningen på beslaget vender mod den korte ende af akslen. Fig. 4. 1. Monter et mellemstykke Billede kan ikke kopieres over. 2. Monter en flad skive Evt.
Page 7
Monter trækstangen til bakken. Sørg for, at den store åbning i rillen vender fremad. Monter som vist på tegningen og med mel- lemstykker de viste steder. Monter rækken af knive i gennem sidepla- derne. Fastgør disse midlertidigt til bakken. Fastgør midterstykket på knivrækken til bakken gennem trækstangen.
Tegning 12 kan ikke kopieres. Som det sidste skal håndtaget justeres og alle samlinger efterspændes. Juster bakken sidelæns indtil løftehåndta- get hviler til højre, når du ser maskinen bag fra. Spænd sidepladerne fast mens du sikrer dig, at håndtaget stadig hviler til højre. Efterspænd det midterste beslag på...
2. Safety precaution • Read this manual carefully so that you understand and follow all safety instructions and operating features completely before you begin to assemble and use the product. • Children should not use the product. • If you feel sick, tired or have consumed alcohol or drugs, you may not use the ma- chine.
3. Identification Følgende dele findes løse i emballagen. 1. Tray 2. Suspension 3. The middle bracket 4. Outboard Bracket 5. Wagon shaft 6. Side 7. Lifting Handle 8. Shaft 9. Double blades (set) 10. Wheel 11. Knives Included are bolts, nuts, spacers, etc. for use in mounting. www.texas.dk...
4. Assembly Before assembly begins, you should put all the parts out. Fit a plastic sleeve on each side of the double blades. Attach a suspension in the center hole in the ear of Justice. Note that the ring of the wheel sus- pension is to face the shorter end of the shaft.
Page 15
At the long side of the shaft is mounted as follows in the correct order. Be aware that bend the bracket facing the short end of the shaft. 1. Attach an adapter 2. Install a flat washer 3. Attach the center bracket 4.
Page 16
Attach the drawbar to the tray. Make sure that the grand opening of the groove facing forward. Install as shown in the drawings and with saddle tube between the places shown. Attach the line of knives in the side plates through-ends.
As the last to handle aligned and all con- nections tightened. Adjust the tray sideways until the lift lever rests on the right when viewing the ma- chine from behind. Tighten the side plates fixed while you make sure that the handle still rests on the right.
7. Specifications Tray Load Capacity Max 60 Kg Construction Steel Working Width 48” (121 cm) Number of Plug Spikes Spike Penetration Depth 3” (7,5 cm) Wheel Type Pneumatic Wheel Size 10x3.5 Tire Pressure (PSI) Hitch Type Pin Style Unit Weight 42 Kg.