Assembly; Battery; Charging - Texas Equipment FRZ 5800 User Manual

Assembly

Please follow the steps in figure:
(Actual model may vary from the illustration shown)
1. Box content
A. Tiller with blades
B. Upper handlebar
C. Clutch handle with safety switch
D. Lower handlebars
E. Depth skid/support wheels
F. Extension blades
G. Panel
H. Side guards
I. Control panel
2. Fit the lower handlebar section. Use the supplied
mountings and bolts. You can choose between 2
different heights of handlebar.
3. Fit the upper handle. Use the supplied assembly kit as
shown.
4. Mount the clutch handle as shown on the picture.
5. Mount the control panel as shown on the picture.
6. Mount the panel as shown on the picture.
7. Mount the side guards using the bolts and nuts supplied.
Note the side guard must go under the body frame.
8. Mount the extension blades using the cotter bolts and
pins.
9. Mount the support wheels with the cotter bolt and pin.
10. The support wheels can be turned, so it works as a
depth skid. Depth can be adjusted.

Battery

This product is delivered without battery and charger. It
is sold separately.
To get the best performance of this machine, it is
recommended to use 2 x 4.0Ah battery.
Warning: Do not try to disassemble, short circuit or put it to
extreme heat or fire, as it can cause serious inquiry and
permanent damage to the battery!
The battery pack is only about 30% charged when delivered.

Charging

Only use the original charger with
art. no. 90070054
Before the battery is being used the first time, it is
recommended to fully charge it first.
The battery has an energy indicator. Press the button and
a number of LED lighs will flash (Illustration 11).
LED lights
All LEDs are lit
LED 1, LED 2, LED 3
are lit.
LED 1, LED 2
are lit.
LED 1 are lit
LED 1 flashes
Battery Pack
Fully charged (75-100%).
The battery pack is
50%-75% charged
The battery pack is
25%-50% charged.
The battery pack is
0%-25% charged
The battery pack is empty.
Charge the battery.
Note: The indicator lighs is only indicative indications, and
is not accurate power indications.
Important: To protect the battery from total discharge, the
machine will stop, when the battery is nearly empty.
The machine must not be started up again after automatic
shutdown, as it can damage the battery. The battery must
be recharges before the work can continue.
For further information, see the user manual which is
included with the battery.
Waste lithium batteries and electric waste must
not be disposed of with the household waste.
Batteries and electric waste should be taken to
your local recycling centre for safe treatment.
Charging
A full charge takes around 60 min for 2.0 Ah battery and 120
min for 4.0 Ah battery.
Only use the original charger, which is included with the
product.
Do not try to charge other type of batteries in the
charger, other than the original batteries with art. no.
90070051 (2.0 Ah) or 90070052 (4.0 Ah).
Keep the charger in a dry and warm environment (10-25
degrees C) and only use it indoor. It should be
connected to a normal 230V AC socket.
Before the battery is being used the first time, it is
recommended to charge it fully.
The surface of the battery can become warm during
charging. This is normal.
Do not cover battery or charger during charging. Allow
free ventilation of air.
Insert the battery into the slots of the charger and slide it
into place until it locks.
There are 4 lights on the charger indicating the status and
state of charge of the battery (Illustration 12).
For further information, see the user manual which is
included with the charger.
Important: The charger will stop, when the battery is full.
However, it is not recommended to leave the battery in
charger for more than 24 hours.
It is recommended to drain the battery completely and fully
charge it whenever possible, as it can increase the health
of the battery. But partial charge will not damage the
battery.
To remove the battery from the charger, hold the button
down and pull the battery out.
12
Status
Charging
Fully charged
Evaluate
Defective