Rear Panel - Panasonic AG-BS300P Operating Instructions Manual

Part Names and Functions (continued)

Rear Panel

DC 24V OUT
CA
IN OUT
1 2 3
1. DC 24V OUT terminal
DC 24 V is output while this unit is operating with the AC power
supply.
This will supply DC power supply to the camera adapter (AG-
CA300).
24 V is not output when this unit is operating with the DC power
supply.
2. CA IN terminal
Connect the BNC cable from the camera adapter.
Connect with the BS OUT connector of the camera adapter
(AG-CA300) using the BNC cable (5C-FW).
3. CA OUT terminal
Connect the BNC cable from the camera adapter.
Connect with the BS IN connector of the camera adapter (AG-
CA300) using the BNC cable (5C-FW).
4. GENLOCK IN terminal
This is a reference signal input terminal to lock this unit with an
external sync.
5. GENLOCK OUT terminal
This is a loop through with the GENLOCK IN connector.
6. VIDEO OUT terminal
Composite signal is output.
Color phase will be also locked to the reference signal when
the BS signal (burst sync) is input as a reference signal into the
GENLOCK IN connector.
The composite signal is not output from the VIDEO OUT
terminal when the video format for the camcorder is set to
1080-23.98PsF.
7. RET IN VIDEO signal input terminal
This is an input terminal for the return video signal from this unit
to the camera adapter (AG-CA300).
This will input a composite signal.
Video cannot be viewed on the CRT VF when the video format
for the camcorder is set to 1080-23.98PsF.
8. RET IN SDI signal input terminal
This is an input terminal for the return video signal from this unit
to the camera adapter (AG-CA300).
This will input a SDI signal.
Video cannot be viewed on the CRT VF when the video format
for the camcorder is set to 1080-23.98PsF.
9. SDI 1 output terminal
This will output the SDI signal that was output from the
camcorder.
11
GEN LOCK VIDEO RET IN SDI OUT
OUT
IN OUT VIDEO SDI 1
4 5 6 7 8 9
13
REMOTE
INCOM/
TALLY
2
TALLY INCOM RET
MAKE 4W SDI
V RTS VIDEO
10 11 12 14 15
10. SDI 2 output terminal
This will output the SDI signal that was output from the
camcorder.
Same signal as the signal output from SDI 1 output terminal is
output.
11. INCOM/TALLY terminal
This is a connector between this unit and the external intercom
system and TALLY system.
12. TALLY selection switch
This is a switch to match with the TALLY system connected to
the INCOM/TALLY terminal.
Select either contact or supplied voltage. For supplied voltage:
compatible with 12 V or less.
Connect to the power outlet using the attached power supply
cable.
MAKE: Select this when the TALLY input signal is a contact
V: Select this when the TALLY input signal is a supplied
voltage
13. INCOM selection switch
This is a switch to match with the INCOM system connected to
the INCOM/TALLY terminal.
Select either 4-wire format or RTS format.
4W: Select this when it is a 4-wire format
RTS: Select this when it is a RTS format
14. RET signal selection switch
This is a switch to select the return signal from this unit to the
camera adapter (AG-CA300).
Select the RET signal supplied to either the RET IN VIDEO
signal input terminal or the RET IN SDI signal input terminal.
VIDEO: Selects the VIDEO signal supplied to the RET IN
VIDEO signal input terminal.
SDI: Selects the SDI signal supplied to the RET IN SDI
signal input terminal.
15. REMOTE terminal
Connect the AG-EC4 (optional) or the AJ-RC10 (optional), and
controls the camcorder.
17
DC 12V IN AC IN
16 18