Jam Clearance - Bostitch BT1855 Original Instructions Manual

JAM CLEARANCE

© Stanley Bostitch
Warning! Always disconnect the air before clearing a jammed fastener.
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
Jam Clearing
compliance for the products.
1. Disconnect the air supply from the tool.
2. Relieve fasteners from pusher (FN1664) or open the magazine (BT1855, FN1650, SX1838 & SL540).
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
3. Open the jam clearing nose door by pulling down and then up on the latch (FN1664 only - Fig 10).
rien que les produits soient conformes aux normes CE.
4. Remove the jammed fastener. In certain circumstances, pliers may be required to remove the fastener.
5. Close the jam clearing nose door latch (FN1664 only - Fig 11).
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
6. Pull pusher back behind fasteners (FN1664) or close the magazine (BT1855, FN1650, SX1838 & SL540).
die CE-Richtlinien für Produkte.
"DIAL-A-DEPTH™" FASTENER CONTROL ADJUSTMENT (FIG 12)
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
The DIAL-A-DEPTH™ Fastener Control adjustment feature provides close control of the fastener drive depth; from flush
zeggen dat de producten voldoen aan de CE-vereisten.
with the work surface to shallow or deep countersink. First, set the air pressure for consistent drive in the specific work,
then use the DIAL-A-DEPTH™ Fastener Control adjustment to give the desired depth of drive.
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
produkterne.
TRIGGER LOCKOUT CONTROL (Fig 13)
The trigger lockout control feature on BOSTITCH pneumatic tools provides a trigger lock feature for added safety control. Push the
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
Lockout control button in or out to activate or lock the tool trigger.
yhdenmukaisuutta.
TRIP OPERATION MODE
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα αντίγραφα του παρόντος
Warning: Always disconnect air supply before making adjustments as accidental actuation may occur, possibly causing injury.
εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
These models (BT1855, FN1650, SX1838, SL540, FN1664) feature a selectable trigger system that allows the user to choose
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
between the following modes of operation:
conformità CE per i relativi prodotti.
SEQUENTIAL TRIP
The sequential trip requires the operator to hold the tool against the work with the safety trip depressed before pulling the trigger. In
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for CE-
order to drive additional fasteners, the trigger must be released and the tool lifted away from the work, before repeating the above
merking for produktet.
mentioned steps. This makes accurate fastener placement easier, for instance on framing, toe nailing and crating applications. The
sequential trip allows exact fastener location without the possibility of driving a second fastener on recoil, as described under
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
Contact Trip (below). The sequential trip tool has a positive safety advantage because it will not accidentally drive a fastener if the
conformidade com a CE para os produtos.
tool is contacted against the work - or anything else - while the operator is holding the trigger pulled.
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
CONTACT TRIP
The common operating procedure on "Contact Trip" tools is for the operator to actuate the safety trip while keeping the trigger
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
pulled, thus driving a fastener each time the work is contacted. This will allow rapid fastener placement on many jobs, such as
conformidad con las normas CE de los productos.
sheathing, decking and pallet assembly. All pneumatic tools are subject to recoil when driving fasteners. The tool may bounce,
releasing the safety trip and if unintentionally allowed to re-contact the work surface with the trigger still actuated (finger still
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
holding the trigger pulled) an unwanted second fastener will be driven.
stanowią deklaracji zgodności CE prezentowanych produktów.
Warning: Tools must NOT be used in Contact Trip mode where changing from one working position to another involves
the use of ladders, stairs or similar structures such as roofs
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
stanowią deklaracji zgodności CE prezentowanych produktów.
SELECTING THE TRIP MODE (Fig 14):
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
To ensure safety, the user should lock the trigger (see Trigger Lockout Control above) before changing the trigger system.
výrobky.
To change the trip mode, rotate the mode switch in the counterclockwise direction. The mode switch will lock
automatically when the indicating arrow is pointing down to the 3 nail icon stamped into the tool frame (Contact Trip
Mode) or to a single nail icon stamped in the tool frame( Sequential Trip Mode). Unlock the trigger to resume tool
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem jelenti
a termék CE-megfelelőségét. operation.
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.