Table of Contents

Advertisement

Inspur Server User Manual
SA5112M4 ( NF5170M4 )

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SA5112M4 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Inspur SA5112M4

  • Page 1 Inspur Server User Manual SA5112M4 ( NF5170M4 )...
  • Page 2 Inspur. The information in this manual is subject to change without notice. Inspur is the registered trademark of Inspur. All the other trademarks or registered trademarks mentioned in this manual are the property of their respective holders.
  • Page 3: Target Audience

    4.Please install the product-compatible operating system and use the driver shipped with the server or provided in Inspur official website. If you use an incompatible operating system or non- Inspur driver, it may cause compatibility issues and affect the normal use of the product, Inspur...
  • Page 4: Table Of Contents

    Content 1 Safety Instructions ......................... 1 2 Product Specification Introduction ....................6 2.1 Introduction ........................6 2.2 Features and Specification ....................7 3 Component Identification ......................10 3.1 Front Panel Component .....................10 3.2 Front Control Panel Buttons and LEDs ................11 3.3 Hard Drive Bay LEDs ......................11 3.4 Rear Panel ...........................12 3.5 PCI Slot Definition .......................13 3.6 System Board Components ....................
  • Page 5 5.3 Identifying the Contents of the Server Shipping Carton .............22 5.4 Installing Hardware Options ....................23 5.5 Installing the Server into the Rack ..................23 5.6 Installing the Operating System ..................24 6 Hardware Options Installation ....................... 25 6.1 Introduction ........................25 6.2 Processor Option ........................25 6.3 Memory Options ........................27 6.4 Hot-plug Hard Drive Option ....................
  • Page 6 12.5 Disposal of Waste Equipment by Users in the European Union ........102 12.6 Korean Notice ........................103 12.7 Chinese Notice .........................103 12.8 Battery Replacement Notice .................... 103 13 Electrostatic Discharge ........................ 105 13.1 Preventing Electrostatic Discharge ................... 105 13.2 Grounding Methods to Prevent Electrostatic Discharge ..........105 14 Inspur Support Guide ........................106...
  • Page 7: Safety Instructions

    For your safety, please do not attempt to remove the cover of the system to remove or replace any component without assistance provided by Inspur. Only service technicians trained by Inspur are authorized to remove the cover of the host, and to remove and replace internal components.
  • Page 8 fire or electric shock. Please place the system far away from the cooling plate and heat sources, and be sure not to block the air vents. Please be sure not to scatter food or liquid in the system or on other components, and do not use the product in humid or dusty environments.
  • Page 9 Please remember that only service technicians trained by Inspur are authorized to remove the cover of the host, and to remove and replace internal components.
  • Page 10 Upon receiving the proper authorization from Inspur and dismounting the internal components, please pay attention to the following: Switch the system power supply off and disconnect the cables, including all connections of the system.
  • Page 11 Safety Introduction When pressing down the release latch and the rail of components is sliding, please be careful; as the sliding may hurt your fingers. Do not overload the AC power supply branch circuits in the rack. The total load of the rack should not exceed 80% of the ratings of the branch circuits.
  • Page 12: Product Specification Introduction

    2 Product Specification Introduction 2.1 Introduction This product adopts the Intel Grantley-EP platform and uses the Wellsburg chip set. It supports the following: ● Two mainstream Intel Xeon E5-26** V4 (or E5-26** V3) series processors. ● 16 DIMM DDR4 memory, up to 2400MHz. ●...
  • Page 13: Features And Specification

    Product Specification Introduction following figure below. Note: 3.5” hard disk bays could hold 3.5”/2.5” hard disks. ● 2.5”×10 Configuration (i.e. Full Configuration) Supports 10 front 2.5” SAS/SATA/SSD hard disks, shown in the figure below. 2.2 Features and Specification Processor Processor Type Intel Xeon E5-26** V4 (or E5-26** V3) Series (supports up to two 145W) Interface Two Socket-R3 slots...
  • Page 14 ID Indicator Interface 1 ID indicator (blue) and its press button Display Controller Controller Type Aspeed 2400 SAS Backplane 3.5x4 Backplane: Supports 3.5”x4 HDDs, SAS backplane provides 1 HD Mini SAS port and 1 8PIN power port; 1 backplane is installed. 2.5x2 Backplane: Supports 2.5”x2 HDDs, provide 2 SATA ports and 1 4PIN power SAS3.0 Backplane port;...
  • Page 15 Product Specification Introduction External Dimension 635 width × 215 height × 955 depth (unit: mm) of Package Host Size 430 width × 44 height × 730 depth (unit: mm) Product Weight Gross weight: 26kg (Gross weight includes: Host + Packing Box + Rail + Parts Kit) Environment Parameters Working Environment...
  • Page 16: Component Identification

    3 Component Identification 3.1 Front Panel Component 2.5” X 8 Hard Drive Bays ● Item Description Quick release levers (2) Front video connector Front USB 3.0 connectors (2) Power button ID LED and button See “Front Control Panel Buttons and LEDs” item 4--9 Hard drive bays 3.5”...
  • Page 17: Front Control Panel Buttons And Leds

    Component Identification Item Description 3.5-inch hard drive bays 3.2 Front Control Panel Buttons and LEDs Item Description USB connectors (2) Power button UID LED and button Network status LED Memory fault LED Power fault LED System overheating LED Fan fault LED System fault LED 3.3 Hard Drive Bay LEDs Item...
  • Page 18: Rear Panel

    3.4 Rear Panel Item Description PSU0 PSU1 PCIe x8 PCIe x16 IPMI management port USB 3.0 connectors (2) Video connector NIC connectors (4) ID LED and button BMC reset button 10 Gigabit NIC LED 10 Gigabit NIC connector...
  • Page 19: Pci Slot Definition

    Component Identification 3.5 PCI Slot Definition 3.6 System Board Components Item Description Processor 0 DIMM slots Processor socket 0 Processor 1 DIMM slots Processor socket 1 GPU power connector System fan connectors (8) I2C connector GPIO connector IPMB connector SATA connectors (6) CLEAR CMOS jumper TCM connector COM connector...
  • Page 20: System Board Jumper Introduction

    Item Description Internal USB 3.0 connector Front VGA connector IPMI management port / rear USB 3.0 connector (2) Processor 1 PCIe x24 slot Rear VGA connector Debug LED GbE port ID LED and button BMC reset button 10 GbE port Processor 1 PCIe x16 slot Processor 0 PCIe x8 slot Processor 0 PCIe x8 (in x16 slot)
  • Page 21: Operations

    Operations 4 Operations 4.1 Power up the Server Insert the power cord plug, then press the Power On button. 4.2 Power down the Server WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment, remove the power cord to remove power from the server. The front panel Power On button does not completely shut off system power.
  • Page 22: Remove The Access Panel

    After performing the installation or maintenance procedure, slide the server back into the rack, and then press the server firmly into the rack to secure it in place. WARNING: To reduce the risk of personal injury, be careful when sliding the server into the rack.
  • Page 23: Install The Access Panel

    Operations CAUTION: For proper cooling do not operate the server without the access panel, air baffle, or fan installed. If the server supports hot-plug components, minimize the amount of time the access panel is open. To remove the component: Power down the server if performing a non-hot-plug installation or maintenance procedure.
  • Page 24: Install The Pci Riser Cage

    Power down the server. Extend the server from the rack. Remove the access panel. Remove the PCI riser cage. 4.7 Install the PCI Riser Cage Power down the server. Extend the server from the rack. Remove the access panel. Install the PCI riser cage. Install the access panel.
  • Page 25: Setup

    Leave a minimum clearance of 121.9 cm (48 in) from the back of the rack to the back of another rack or row of racks. Inspur Servers draw in cool air through the front door and expel warm air through the rear door. Therefore, the front and rear rack doors must be adequately ventilated to allow ambient room air to enter the cabinet, and the rear door must be adequately ventilated to allow the warm air to escape from the cabinet.
  • Page 26: Temperature Requirements

    • Side—The clearance between the installed rack component and the side panels of the rack must be a minimum of 7 cm (2.75 in). 5.1.2 Temperature Requirements To ensure continued safe and reliable equipment operation, install or position the system in a well-ventilated, climate-controlled environment.
  • Page 27: Electrical Grounding Requirements

    Because of the high ground-leakage currents associated with multiple servers connected to the same power source, Inspur recommends the use of a PDU that is either permanently wired to the building’s branch circuit or includes a nondetachable cord that is wired to an industrial-style plug.
  • Page 28: Rack Warnings

    5.2 Rack Warnings WARNING: To reduce the risk of personal injury or damage to the equipment, please be sure of the following: ● The leveling jacks are extended to the floor. ● The full weight of the rack rests on the leveling jacks. ●...
  • Page 29: Installing Hardware Options

    Setup 5.4 Installing Hardware Options Install any hardware options before initializing the server. For options installation information, refer to the option documentation. For server-specific information, refer to “Hardware options installation.” 5.5 Installing the Server into the Rack CAUTION: Always plan the rack installation so that the heaviest item is on the bottom of the rack.
  • Page 30: Installing The Operating System

    Ruijie assisted installation—Insert the Ruijie server kit CD into the CD-ROM drive and reboot the server. ● Manual installation—Insert the operating system CD into the CD-ROM drive and reboot the server. This process may require you to obtain additional drivers from the Inspur website (http://www.inspur.com/eportal/ui?pageId=444443).
  • Page 31: Hardware Options Installation

    Hardware Options Installation 6 Hardware Options Installation 6.1 Introduction If more than one option is being installed, read the installation instructions for all the hardware options and identify similar steps to streamline the installation process. WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them.
  • Page 32 Step 2: Install CPU into the CPU socket, and then remove the protective cover. Step 3: Clamp CPU with CPU fixing plate, and then close the two locking levers firmly.
  • Page 33: Memory Options

    Hardware Options Installation Step 4: Fix the CPU heatsink above CPU, and then fasten the bolts on the heatsink. Note: ● It is required to coat thermal grease evenly onto the contact position between CPU heatsink and CPU. ●The direction of CPU heatsink fins should be identical with the system inlet/outlet direction.
  • Page 34 to halt during BIOS initialization. All memory installed in the server must be the same type. ● DIMM slot layout is as shown in the following figure: ● DIMM population guidelines: Only DIMMs of the same type could be used in the same machine. Detailed DIMM population and combination principles are as follows: a 、...
  • Page 35: Hot-Plug Hard Drive Option

    Hardware Options Installation 6.4 Hot-plug Hard Drive Option When adding hard drives to the server, observe the following general guidelines: ● The system automatically sets all device numbers. ● If only one hard drive is used, install it in the bay with the lowest device number; please check the hard drive device number on the pull-tag.
  • Page 36: Removing A Hot-Plug Hard Drive

    Use four hard disk bolts to fix the hard disk onto the bracket. 6.5 Removing a Hot-plug Hard Drive CAUTION: For proper cooling do not operate the server without the access panel, baffles, expansion slot covers, or blanks installed. If the server supports hot-plug components, minimize the amount of time the access panel is open.
  • Page 37: Redundant Hot-Plug Power Supply Option

    Hardware Options Installation Remove the hard drive. 6.6 Redundant Hot-plug Power Supply Option CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays are populated with either a component or a blank. Access the product rear panel. Remove the power supply blank.
  • Page 38: Expansion Board Options

    Install the power supply in the power supply bay. Connect the power cord to the power supply. Route the power cord through the power cord anchor or cable management arm. Reposition the cable management arm into the operating position. Connect the power cord to the power source. Be sure that the power supply LED is green.
  • Page 39 Hardware Options Installation Step 2: Pull out the expansion card in the arrow direction, and replace it with a new expansion card.
  • Page 40: Air Baffle Replacement

    6.8 Air Baffle Replacement Step 1: Open the top cover of the chassis. Step 2: Use fingers to lift up both ends of the air baffle, and remove the air baffle vertically.
  • Page 41: Cabling

    Cabling 7 Cabling 7.1 External RAID/SAS card configuration cabling 7.2 Onboard SATA configuration cabling...
  • Page 42: Bios Setup

    8.1 System BIOS Setup Methods Power on the server. The system will then start to boot. When the following content appears below Inspur logo on the screen: ● Press <DEL> to SETUP or <TAB> to POST or <F12> to PXE Boot.
  • Page 43: Bios Settings

    BIOS Setup Note: Options in grey are not available. Options with symbol “ ” have a sub-menu. Control key instruction table Press Key Function <Esc> Exit or return from sub-menu to main menu <←> or <→> Select a menu <↑> or <↓> Move the cursor up or down <Home>...
  • Page 44: Advanced Menu

    8.2.2 Advanced Menu Advanced Menu Interface Instruction Table Interface Parameters Function Description Trusted Computing Trustable computing configuration ACPI Settings Advanced configuration and power interface settings AST2400 Super IO Configuration AST2400 I/O chip parameter configuration Serial Port Console Redirection Serial port console redirection settings PCI Subsystem Settings PCI subsystem settings Network Stack Configuration...
  • Page 45 BIOS Setup Trusted Computing Menu Interface Instruction Table Interface Parameters Function Description Security Device Support BIOS security device support settings Current Status Information Status information of the current security device 8.2.2.2 ACPI Settings Advanced Menu Interface Instruction Table Interface Parameters Function Description Enable ACPI Auto Configuration To enable ACPI automatic configuration...
  • Page 46 AST2400 Super IO Configuration Menu Interface Instruction Table Interface Parameters Function Description Super IO Chip The current I/0 chip Serial Port 1 Configuration Serial port 1 configuration 8.2.2.4 Serial Port Console Redirection Serial Port Console Redirection Menu Interface Instruction Table Interface Parameters Function Description Console Redirection...
  • Page 47 BIOS Setup Console Redirection Settings Menu Interface Introduction Interface Parameters Function Description Terminal Type Terminal type settings Bits per second Baud rate settings Data Bits Data bits settings Parity Parity check settings Stop Bits Stop bits settings Flow Control Flow control settings VT-UTF8 Combo Key Support VT-UTF8 Combo key support settings Recorder Mode...
  • Page 48: Csm Configuration

    8.2.2.6 CSM Configuration CSM Configuration Menu Interface Instruction Table Interface Parameters Function Description CSM Support CSM support settings GateA20 Active A20 address line’s control mode settings Option Rom Message Option Rom display mode settings Boot option filter Boot option filter settings Option ROM execution Option Rom execution method Network...
  • Page 49: Usb Configuration

    BIOS Setup 8.2.2.7 USB Configuration USB Menu Interface Instruction Table Interface Parameters Function Description Legacy USB Support Legacy USB device settings XHCI Hand-off Extensible host controller interface settings, orienting to USB 3.0. EHCI Hand-off Enhanced host controller interface settings, orienting to USB2.0. USB Mass Storage Driver Support USB mass storage driver support settings Port 60/64 Emulation...
  • Page 50: Chipset Menu

    Onboard LAN Configuration Menu Interface Instruction Table Interface Parameters Function Description Onboard NIC1 Control Onboard network card NIC1 switching settings Onboard NIC2 Control Onboard network card NIC2 switching settings Onboard NIC1 ROM Onboard network card NIC1 PXE Oprom switching settings Onboard NIC2 ROM Onboard network card NIC2 PXE Oprom switching settings 8.2.3 Chipset Menu...
  • Page 51: Processor Configuration

    BIOS Setup 8.2.3.1 Processor Configuration Processor Configuration Menu Interface Instruction Table Interface Parameters Function Description Processor information submenu, and processor detailed Processor Information information. Hyper Threading Technology Hyper threading technology settings Core Enabled CPU core number settings Execute Disable Bit Execute disable bit settings Intel TXT Support Intel trusted execution technology support settings...
  • Page 52: Advanced Power Management Configuration

    8.2.3.2 Advanced Power Management Configuration Advanced Power Management Configuration Menu Interface Instruction Table Interface Parameters Function Description Power Technology To set power management Config TDP TDP settings CPU P State control sub-menu, enabled when Power Technology is CPU P State Control set to [Custom].
  • Page 53 BIOS Setup CPU P State Control Menu Interface Instruction Table Interface Parameters Function Description EIST(P-states) EIST enable/disable settings Turbo Mode Turbo mode enable/disable settings CPU C State Control CPU C State Control Menu Interface Instruction Table Interface Parameters Function Description Package C State limit C state limit settings CPU C3 report...
  • Page 54: Qpi Configuration

    Energy Performance Tuning Menu Interface Instruction Table Interface Parameters Function Description Energy Performance Tuning To select BIOS or OS to carry out energy performance tuning Energy Performance BIAS Energy performance management settings Workload Configuration Workload configuration 8.2.3.3 QPI Configuration QPI Configuration Menu Interface Instruction Table Interface Parameters Function Description QPI Status...
  • Page 55: Memory Configuration

    BIOS Setup 8.2.3.4 Memory Configuration Memory Configuration Menu Interface Instruction Table Interface Parameters Function Description Enforce POR To execute POR settings Memory Frequency Memory frequency settings ECC Support ECC support settings Rank Multiplication Rank multiplication settings LRDIMM Module Delay LRDIMM module delay settings Data Scrambling Data scrambling settings Refresh Options...
  • Page 56 Memory RAS Configuration Memory RAS Configuration Menu Interface Instruction Table Interface Parameters Function Description As for memory mode configuration, there’re 3 options of Memory Mode [Independent], [Mirroring] and [Lock Step]. Lockstep X4 DIMMs X4 DIMMs’ Lockstep enable/disable settings Memory Rank Sparing Memory Rank sparing settings Correctable Error Threshold Correctable error threshold settings...
  • Page 57: Pch Configuration

    BIOS Setup IIO Configuration Menu Interface Instruction Table Interface Parameters Function Description IIO0 configuration sub-menu, used to set link speed of PCIE device of IIO0 Configuration CPU0. IIO1 configuration sub-menu, used to set link speed of PCIE device of IIO1 Configuration CPU1.
  • Page 58 PCH SATA Configuration Menu Interface Instruction Table Interface Parameters Function Description SATA Controller SATA controller switching settings As for SATA mode configuration, there’re two modes of [AHCI] and [RAID] Configure SATA as for setting. SATA Port 0/1/2/3/4/5 Information of hard disks connected to onboard SATA port 0/1/2/3/4/5. SATA RAID mode configuration Set the option of Configure SATA to [RAID].
  • Page 59 BIOS Setup information or not) should be displayed. Press Key Description ↑↓ Used to move cursor in different menus or to change values of menu options. To select the next menu setting option. Enter To select a menu. To exit menu or return to previous menu from sub-menu. SATA RAID configuration interface has the following 4 executable menus: Create RAID Volume To create an RAID volume.
  • Page 60 System displays the following menu options: Please enter a volume label name less than 16 characters without containing any Name special character. Please select RAID volume level. If no volume has been created at present, there are four volume levels of RAID0 (Stripe), RAID1 (Mirror), RAID10 (RAID0+1) and RAID5 (Parity) for selection.
  • Page 61 BIOS Setup Delete RAID Volume Menu After entering Delete RAID Volume menu, the system should prompt: “Deleting a volume will reset the disks to non-RAID. Warning : ALL DISKS DATA WILL BE DELETED.”. To delete an RAID volume, please press [DEL], system prompts: “ALL DATA IN THE VOLUME WILL BE LOST!”...
  • Page 62 Exit Menu System prompts: “Are you sure you want to exit?(Y/N):”, enter “Y”, to exit SAS RAID configuration interface, enter “N”, to cancel exit operation. 8.2.3.7 Server ME Configuration Server ME Configuration Menu Interface Instruction Table Interface Parameters Function Description Operational Firmware Version Operational ME firmware version Recovery Firmware Version...
  • Page 63: Server Management

    BIOS Setup 8.2.3.8 Common Configuration Common Configuration Menu Interface Instruction Table Interface Parameters Function Description MMCFG Base MMCFG base address settings Isoc Mode Isoc mode settings MeSeg Mode MeSeg mode settings Numa Numa switching settings BIOS Guard BIOS guarding settings VGA Priority Integrated video card and external video card priority settings 8.2.4 Server Management...
  • Page 64 Server Mgmt. Menu Interface Instruction Table Interface Parameters Function Description BMC Firmware Version BMC firmware version FRB-2 Timer FRB-2 timer settings FRB-2 Timer timeout FRB-2 timer timeout settings FRB-2 Timer policy Policy settings after FRB-2 timer timeout OS Watchdog Timer OS watchdog timer settings OS Wtd Timer timeout OS watchdog timer timeout settings...
  • Page 65 BIOS Setup 8.2.4.2 View FRU Information The View FRU Information menu lists BMC FRU information read by BIOS, and BIOS will interact with BMC at each system restart, keeping synchronous update of FRU information. 8.2.4.3 BMC Network Configuration BMC Network Configuration Menu Interface Instruction Table Interface Parameters Function Description Configuration BMC Network Status Parameter: It could set static IPs,...
  • Page 66 network via BIOS. If no operation is carried out in BIOS, by default, it will read BMC. It will configure its dedicated management port and sharelink management port. Taking its dedicated management port as an example, the BIOS reading configuration is as shown in the following figure: BIOS could carry out Dynamic and Static network settings on BMC Dedicated management port and sharelink management port.
  • Page 67 BIOS Setup enter the Router IP Address to set manually, after configuration is completed, press Enter to confirm, and an example is as shown in the following figure: When the Static IP configuration is done, press F10 to save and restart. BIOS will carry out Static IP configuration for BMC.
  • Page 68 Add User Operation Select the User Name option and press Enter to pop up the User Name box. Enter the user name to set manually. After configuration is completed, press Enter to confirm. Select the User Password option and press Enter to pop up the User Password box. Enter the user password to set manually.
  • Page 69 BIOS Setup Delete User Operation Select the User Name option, and click Enter to pop up the User Name box. Manually enter the user name to delete. After configuration is completed, press Enter to confirm. Select the User Password option. Press Enter to pop up the User Password box. Manually enter the user password to delete.
  • Page 70 Change User Settings Select the User Name option. Click Enter to pop up the User Name box. Manually enter the user name to modify. After configuration is completed, click Enter to confirm. Select the User Password option. Click Enter to pop up the User Password box. Manually enter the user password, and click Enter to confirm.
  • Page 71 BIOS Setup 8.2.4.5 System Health Information System Health Information Menu Interface Instruction Table Interface Parameters Function Description System Temperature Information System temperature information sub-menu System Fan Speed System fan speed sub-menu System Voltage Information System voltage information sub-menu System Temperature Information...
  • Page 72: Security Menu

    System Fan Speed System Voltage Information 8.2.5 Security Menu Security Menu Interface Instruction Table Interface Parameters Function Description Administrator Password Create a password for administrator User Password Create a password for normal user...
  • Page 73: Boot Menu

    BIOS Setup 8.2.6 Boot Menu Boot Configuration Menu Interface Instruction Table Interface Parameters Function Description Bootup NumLock State Numlock state settings after bootup Boot Options Retry The booting device polling settings To boot quietly, set this option to Enabled, and boot logo displays Quiet Boot as that set by manufacturer, disabled, boot logo displays as AMI’s default logo.
  • Page 74 Taking Boot Option #1 as an example, you could set the first boot device for the system. Move the cursor to Boot option #1. Press Enter to pop up the boot option for selection: i.e. IBA GE slot 0400 v1543, UEFI: Built-in EFI Shell, UEFI: USB2.O DISK 1100, USB2.O DISK 1100, etc.
  • Page 75: Firmware Update

    BIOS Setup Save & Exit Menu Interface Instruction Table Interface Parameters Function Description Save Changes and Exit To save changes and exit Discard Changes and Exit To discard changes and exit Save Changes and Reset To save changes and reset Discard Changes and Reset To discard changes and reset Save Changes...
  • Page 76 When there is no change in ME part, to update BIOS, it is only required to execute command: Afudos BIOS.bin /b /p /n /x. Parameter instructions: /b -- Program Boot Block /p -- Program Main BIOS /n -- Program NVRAM /x -- Don’t Check ROM ID /me -- Program ME Entire Firmware Block Use Afudos tool to update BIOS in Linux OS...
  • Page 77 BIOS Setup Meanwhile, put bin files of corresponding BIOS into this folder and enter command: afuwinx64.exe BIOS.BIN /P /B /N /X /R, to update BIOS files. The GUI method is provided in Windows to refresh BIOS. Taking Windows 2008R2 OS as an example, use AFUWINGUI tool to update BIOS.
  • Page 78: Bmc Settings

    The Inspur Server management software is a control unit for server management, which is compatible with the management standard IPMI2.0 specification. Below are the main functions of the Inspur Management Software: ●...
  • Page 79: Functional Modules

    This chapter introduces the Inspur Server Management System Module Composition, as well as the functions of these modules. 9.2.1 Module Composition The Inspur Server Management System is mainly composed of the IPMI module, command line module, WEB module, KVM Over IP and virtual media. ●...
  • Page 80: Web Interface Introduction

    ● Virtual Media: A method of providing remote access on local media (CD-ROM, floppy drive or CD/floppy disk iso file) in the form of virtual CD driver and floppy drive on server via the internet. Note: If the Java runtime environment does not meet the requirement, please download here: http://www.oracle.com/technetwork/java/javase/downloads/index.html 9.3 Web Interface Introduction...
  • Page 81 BMC Settings 9.3.2 Web Interface Introduction The Web Interface helps users accomplish server management. The Web Interface also has a help function so users can click the help button in the case that they may need it. The Web interface is divided into four parts, as shown in the following figure. ●...
  • Page 82 ● Viewing system information ● Storage ● Remote control ● Power management ● Event and log query ● Real-time monitoring ● Diagnosis and orientation ● System maintenance ● System configuration etc. For detailed introduction on all functions, please refer to the following chapters. ●...
  • Page 83 BMC Settings sensor, voltage sensor, fan speed, power supply, processor status, memory status and power unit status information. ● Device status: Display status information of the front hard disks and onboard NIC. ● FRU information: Display FRU information. ● History: Display the history information of inlet air temperature and total power.
  • Page 85: Storage

    BMC Settings 9.4 Storage Select “Storage” on navigation tree to open the storage interface, which contains four interfaces of controller, physical drives, logical drives and enclosure, shown in the following figure. ● Controller: Displays the controller information of the storage system. ●...
  • Page 86: Remote Control

    9.5 Remote Control Select “Remote Control” on the navigation tree to open the remote control interface, which contains six interfaces of console redirection (KVM)”, server power control, server location, configure remote session, virtual media devices and mouse modes settings, shown in the following figure.
  • Page 87 BMC Settings...
  • Page 88: Power Supply And Fan

    9.6 Power Supply and Fan Select “Power Supply and Fan” on the navigation tree to open the power supply and fan page. It contains three pages of power supply monitoring, power supply management, fan speed control, as shown in the following figure. ●...
  • Page 89: Bmc Configuration

    BMC Settings 9.7 BMC Configuration Select “BMC Configuration” on the navigation tree to open the BMC Configuration page. This page contains information related to the BMC network management, services, NTP settings, SMTP settings, alert settings, active directory settings, LDAP/E-Directory settings, user management, IP access control and BMC share NIC switch, shown in the following figure.
  • Page 91 BMC Settings...
  • Page 92: Logs

    9.8 Logs Select “Logs” on navigation tree to open related log page. This contains system event log, BMC system audit log, black box log, event log setting and system and audit log settings, shown in the following figure. ● System event log: Displays various event logs generated by server. ●...
  • Page 93: Fault Diagnosis

    BMC Settings 9.9 Fault Diagnosis Select “Fault Diagnosis” on navigation tree to open fault diagnosis page, which contains three pages of BMC recovery, capture screen and host POST code, shown in the following figure. ● BMC recovery: Contains two functions of BMC warm reset and KVM service restart. ●...
  • Page 94: System Maintenance

    9.10 System Maintenance Select “System Maintenance” on the navigation tree to open system maintenance page. It contains BMC firmware update, BIOS firmware update, restore factory defaults and system administrator, shown in the following figure. ● BMC firmware update: Updates BMC FW via BMC Web interface; ●...
  • Page 95: Command Line Function Introduction

    BMC Settings 9.11 Command Line Function Introduction This chapter introduces Web interface of the management system, as well as operation steps to the Web interface login. ● Login command line Introduces methods of login command line. ● Command line function introduction Introduces command line functions.
  • Page 96 password: rootuser. After logging in, enter the command line interface: Enter help to view online help: 9.11.2 Command Line Function Introduction 9.11.2.1 Network Information Acquisition and Configuration: Acquire and configure BMC’s network information via ipconfig instructions: 9.11.2.2 Sensor Information Acquisition: Via sensor instruction, acquire the information list of all sensors:...
  • Page 97 BMC Settings 9.11.2.3 FRU Information Acquisition and Configuration: Via FRU instruction, acquire FRU configuration information: 9.11.2.4 Chassis Status Acquisition and Control: Via chassis instruction, acquire and control system power status.
  • Page 98 Acquire system power status: 9.11.2.5 User Acquisition, Adding and Deleting: Via user instruction, acquire the user list, add or delete users. Acquire user list: 9.11.2.6 BMC Version Acquisition and BMC Restart Via mc instruction you may acquire BMC version information and restart BMC.
  • Page 99 BMC Settings Acquire BMC version information: 9.11.2.7 Fan Work Mode Configuration and Fan Speed Acquisition: Via fan instruction, you may set fan work mode, and acquire fan speed. Fan speed acquisition: 9.11.2.8 Power Module Information Acquisition and Configuration: Via Psu instruction, you may acquire power module information, and set power module as main output.
  • Page 100: Time Zone Table

    Power module information acquisition: 9.11.2.9 Change Root Password: Via password instruction, you may change the root user’s password: 9.12 Time Zone Table Name of Time Zone Time Dateline Standard Time (GMT-12:00) International Date Line West Samoa Standard Time (GMT-11:00) Midway Island, Samoa Hawaiian Standard Time (GMT-10:00) Hawaii Alaskan Standard Time...
  • Page 101 BMC Settings Greenland Standard Time (GMT-03:00) Greenland Mid-Atlantic Standard Time (GMT-02:00) Mid-Atlantic Azores Standard Time (GMT-01:00) Azores Cape Verde Standard Time (GMT-01:00) Cape Verde Islands GMT Standard Time (GMT) Greenwich Mean Time: Dublin, Edinburgh, Lisbon, London Greenwich Standard Time (GMT) Casablanca, Monrovia Central Europe Standard Time (GMT+01:00) Belgrade, Bratislava, Budapest, Ljubljana, Prague Central European Standard Time...
  • Page 102 Myanmar Standard Time (GMT+06:30) Yangon Rangoon S.E. Asia Standard Time (GMT+07:00) Bangkok, Hanoi, Jakarta North Asia Standard Time (GMT+07:00) Krasnoyarsk China Standard Time (GMT+08:00) Beijing, Chongqing, Hong Kong SAR, Urumqi Singapore Standard Time (GMT+08:00) Kuala Lumpur, Singapore Taipei Standard Time (GMT+08:00) Taipei W.
  • Page 103: Common Faults, Diagnosis And Troubleshooting

    Common Faults, Diagnosis and Troubleshooting 10 Common Faults, Diagnosis and Troubleshooting This chapter introduces the common server faults, as well as corresponding diagnosis and troubleshooting suggestions. 10.1 Common Faults No power after startup ● After the machine is connected with power cable, no power is provided for the machine while pressing the On/Off button.
  • Page 104 If there is a machine and a power module of the same type, you could change the power module to test whether there is a power module fault. If the instructions above do not resolve the problem, please contact Inspur customer service.
  • Page 105 If the USB device is normal when connecting to other hosts, the server may be abnormal: please call Inspur technical hotline for support. If the USB device turns out to be abnormal when connecting to other hosts, please replace the USB device.
  • Page 106: Battery Replacement

    Remove the full-length expansion board retainer if any full-length expansion boards are installed. Remove the PCI riser cage. Remove the air baffle. Remove the battery. To replace the component, reverse the removal procedure. For more information about battery replacement or proper disposal, contact Inspur Customer Service.
  • Page 107 Regulatory Compliance Notices 12 Regulatory Compliance Notices 12.1 Regulatory Compliance Identification Numbers For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique regulatory model number. The regulatory model number can be found on the product nameplate label, along with all required approval markings and information.
  • Page 108: Regulatory Compliance Notices

    Compliance with these directives implies conformity to applicable harmonized European standards (European Norms) that are listed in the EU Declaration of Conformity issued by INSPUR for this product or product family and available (in English only) within the product documentation.
  • Page 109: Korean Notice

    Regulatory Compliance Notices information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product. 12.6 Korean Notice Class A Equipment Class B Equipment 12.7 Chinese Notice Class A Equipment...
  • Page 110 Batteries, battery packs, and accumulators should not be disposed of together with the general household waste. To forward them to recycling or proper disposal, use the public collection system or return them to Inspur, an authorized Inspur Partner, or their agents.
  • Page 111: Electrostatic Discharge

    Use a portable field service kit with a folding static-dissipating work mat. If you do not have any of the suggested equipment for proper grounding, have an authorized reseller install the part. For more information on static electricity or assistance with product installation, contact Inspur Customer Service.
  • Page 112: Inspur Support Guide

    14 Inspur Support Guide ● Inspur Global Service Support Global Technical Service Hotline: 1-844-860-0011 (Toll Free) 1-646-517-4966 (Direct Phone) Global Technical Service Email: serversupport@inspur.com ● Information customer needs to provide when requesting for support: Contact name Phone number E-mail address...

This manual is also suitable for:

Nf5170m4

Table of Contents

Save PDF