Kicker PF150S11 Assembly Manual
  1. Manuals
  2. Brands
  3. Kicker Manuals
  4. Subwoofer
  5. PF150S11
  6. Assembly manual
Kicker PF150S11 Assembly Manual

Kicker PF150S11 Assembly Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Designed for 2011 - 2012 Ford® F-150 Super-Cab vehicles with base radio and
2013 - 2014 Ford® F-150 Super-Cab vehicles with non MyFord Touch® radios.
Subwoofer Power Harness
©2012 Stillwater Designs
PF150S11-A4-20141002
PF150S11
Subwoofer Assembly
M6 Bolts x3
M8 Bolts x3
M8 Nut Inserts x3
(Requires Nut Insert Tool)
Wire Taps x2
Adapter Harness
Subwoofer Body
Harness
25A Fuse
Wire Ties x6
Foam Strips
M6 Speed Clips x3
Adhesive Covers x3
1

Advertisement

Table of Contents
loading

Related Manuals for Kicker PF150S11

Summary of Contents for Kicker PF150S11

  • Page 1 PF150S11 Designed for 2011 - 2012 Ford® F-150 Super-Cab vehicles with base radio and 2013 - 2014 Ford® F-150 Super-Cab vehicles with non MyFord Touch® radios. Subwoofer Assembly Subwoofer Body Harness Subwoofer Power Harness M6 Bolts x3 25A Fuse M8 Bolts x3...
  • Page 2 Amplifi er Assembly Amplifi er Body Harness Amplifi er Power Harness 25A Fuse Wire Ties x6...
  • Page 3 Radio Removal (Trucks with Console Mounted Shifter) 1. Set the parking brake. 2. Turn the ignition switch to the run position (do not start). 3. Shift the transmission to “Neutral”. 4. Lift up on the shifter bezel to remove. Fig. 1 5.
  • Page 4 13. Slide the console back approximately three inches to allow access to the screws securing the bottom of the left and right vent assemblies and remove the screws. Fig. 7 14. Remove the two screws in the top of the instrument cluster bezel. Fig. 8 Fig.
  • Page 5 22. Carefully pry loose the aux. input panel with a pick tool or small fl at screwdriver, disconnect wiring and remove the screw retaining the radio bezel. Fig. 13 23. Pull loose the radio bezel and disconnect wiring. Fig. 14 24.

  • Page 6: Fig.

    31. Pull the air bag assembly out approximately three inches to gain access to the screw securing the top of the right vent assembly and remove the screw. Place a towel under the airbag assembly to prevent it from scratching the dash. Fig. 19 32.

  • Page 7: Fig.

    39. Make a small incision in the rubber grommet and pass the power wires into the cabin. 40. Remove the driver’s side threshold panel along the bottom of the front door opening. 41. Pull back the rubber door molding and then pull back on the kick panel to remove it.

  • Page 8: Fig.

    52. Install the white three pin connector on the end of the amplifi er power harness inside the cabin. It does not matter what order the three wires are in on the three pin connecter but the terminals can only be inserted one way.

  • Page 9: Fig.

    61. Remove the jack and mounting plate and tape the paper template to the carpet lining up the three marks with the corresponding markings on the template. Fig. 32 62. Cut the carpet along all the dotted lines on the template. When you are fi nished you will have two fl aps, one large and one small.

  • Page 10: Fig.

    73. Reinstall all previously remove parts in reverse order. 74. Reconnect negative battery cable. Fig. 36 Troubleshooting the Kicker Integrated Systems If you experience a problem once the Subwoofer is installed use this guide to locate the trouble. The radio is working, but the Subwoofer is not working: •...
  • Page 11 Low battery voltage Recharge the battery If you continue to experience problems after troubleshooting, please contact KICKER Technical Support at (800) 256-0808 ext. 6009, or support@kicker.com. stillwater designs P.O. Box 459 • Stillwater, Oklahoma 74076 • USA • (405) 624–8510...

Table of Contents