Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Firstech CM5200
Summary of Contents for Firstech CM5200
-
Page 3: Table Of Contents
Green/White Loop ........................... 8 Reservation Mode for Manual Transmissions ..................9 ADS Blade Cartridge Slot and Connector ..................... 10 CM5200 Wiring Schematic (Remote Start) .................... 11 CM5000 Wiring Schematic (Alarm and Remote Start) ................. 12 Option Programming Tables ........................19 Option Menu Descriptions ........................ -
Page 4: Introduction
This installation manual is for Version Simplified Firmware (V.SF) of the CM5200 and CM5000 control modules. Some functions and features are not described in this install manual. Please see the remote’s user manual(s) for detailed descriptions on those features. -
Page 5: Installation Basics
Technical Support Contacts Installation Basics If you are new to installing Firstech Series Remote Starts and / or Alarms, we highly recommended that Firstech technical support is reserved for authorized dealers only. you thoroughly review this manual to installing your first unit. -
Page 6: Remote Programming Routine
STEP 2, code additional remotes by tapping Button I on two way remotes or the Lock button on one way remotes. The parking lights What is this cartridge slot on the rear of the CM5000 and CM5200? will flash once confirming each additional remote. All systems (except the P2WSSR), can recognize up to three remotes. -
Page 7: Placement And Use Of Components
The vehicle starts and shuts down 3 times in a row. Every 2 Way remote - Firstech system includes an optional thermistor, which must be plugged into the 2 pin port of the control module for use. This plug is blue on the CM5000. The use of the thermistor allows... -
Page 8: Hood Pin
There are new features that adjust tach reading methods on 4 flashes, rest, then repeat Triggered option 2-01. IMPORTANT: The remotes must be coded prior to setting up tach sensing. Firstech Panic with remote 5 flashes, rest, then repeat recommends using a digital multimeter to test for tach. -
Page 9: Alternator Sensing
STEP 2: To change the option number you wish to program, use the left and right arrow keys on the OP500. It will scroll through the options available in menu 1 and then move to menu 2, then 3 and 4. Use STEP 3: Learn tach. -
Page 10: Reservation Mode For Manual Transmissions
If the vehicle’s engine does not shut off, check the door trigger connection or wait for the factory dome- accessory, starter or a horn honk output. light to go out. The Firstech system is in reservation mode and the vehicle is ready to safely remote start. 4-14 Starter Option –... -
Page 11: Ads Blade Cartridge Slot And Connector
The e-brake and door trigger input must be connected and the option must be turned on through This is the main feature of the CM5000 and CM5200. The slot gives you the ability to use the Blade-AL the remote for this feature to work. -
Page 12: Cm5200 Wiring Schematic (Remote Start)
CM5200 Wiring Schematic (Remote Start) OPTION GROUP 4 The CM5200 is the control module for all remote start units. This controller is universal regardless of Feature Default Setting - I Optional Setting - II Optional Setting - III Optional Setting - IV remote or antenna type. -
Page 13: Cm5000 Wiring Schematic (Alarm And Remote Start)
Starter-Kill Relay Anti-Grind + Starter Kill Anti-Grind 2nd Stage Passive Starter Kill White Input 3-06 Factory Alarm Option (CM5200 Only) ( - ) 1 Black 3-07 Siren Duration (Upon Alarm Trigger) 30 Sec. 60 Sec. 1 ( + ) On Lock, Unlock, and... - Page 14 Connector 1 (CN1), 8-Pin Pin 4 Grey/White - 1 stage negative (-) input. (Warn away) Connector 11 (CN11), 2-Pin (Pre-wired Thermistor) Pin 1 Red - Constant 12V positive (+) power input. This wire must be connected. The proper vehicle wire will test (+) 12V at all times - while the key is in the off position, the on position and during Plug optional thermistor into this connector to monitor the vehicles’...
- Page 15 IMPORTANT: For anti-grind and starter-kill applications, the yellow wire goes to the Pin 1 Black - Negative (-) ground. starter side of the vehicles starter wire and the yellow/black goes to the key side. Pin 2 White - 2 stage negative (-) input. (Instant trigger) Pin 7 Green –...
- Page 16 hood is opened while the alarm is armed. You can connect this wire to the hood pin supplied with Pin 4 Light Blue/White - Brake 12V positive (+) input. This input must be connected as it provides a this kit, or to a wire in the vehicle that shows (-) only while the hood is open. shut down for the remote start.