Cm5000 Wiring Schematic (Alarm And Remote Start) - Firstech CM5200 Installation Manual

Option Programming Tables
OPTION GROUP 1
Feature Default Setting - I Optional Setting - II
1-01 Unlock before, Lock after, starting Off
1-02 Lock / Unlock pulse duration 0.8 sec 2.5 sec
1-03 Driver's priority unlock Off
1-04 Double pulse unlock Off
After Start Shutdown
1-05 Rearm Output After Shutdown Only
and First Lock
Passive locking with No Passive Locking with
1-08 Locking while in Passive Arming
Passive Arming Passive Arming
1-09 Ignition controlled door locks Off
Ignition and Acc Pulse -
1-11 Ignition / Accessory Out Upon Unlock Off same timing as disarm
pulse
1-13 Double Pulse Disarm Input Single Pulse Double Pulse
Auto Lock Mode (2 Way International
1-14 Off
Remotes)
OPTION GROUP 2
Feature Default Setting - I Optional Setting - II
2-01 Tach Sensing Method Optimal Tach Method Previous Tach Method
2-02 Turbo Timer Off 2 Min
2-03 Diesel Timer Wire 3~99sec (10sec Default)
2-04 Trigger Start Off Single Pulse
3 Hour (4 minute 1.5 Hour(4 minute
Timer Start, or, Minimum Interval
2-06 runtime, double for runtime, double for
Between Cold Starts
Diesel) Diesel)
2-07 Remote Start Runtime 15 Min 25 Min
2-10 Engine Sensing Tach Alternator
+0.2 Seconds to Crank
2-12 Crank Time Standard
Time
OPTION GROUP 3
Feature Default Setting - I Optional Setting - II
3-03 Dome Light Delay Off
3-04 Starter-Kill Relay Anti-Grind + Starter Kill Anti-Grind
3-06 Factory Alarm Option (CM5200 Only) Off
3-07 Siren Duration (Upon Alarm Trigger) 30 Sec. 60 Sec.
3-08 Horn Output (CM5200 Only) On Double Lock Only On Lock and Unlock
Constant Output
3-09 Horn Output When Alarm is Triggered Pulsed Output
(Secondary Siren)
19
Optional Setting - III Optional Setting - IV
Lock After Remote Start Lock After Shutdown
On
Only Only
0.125 sec 3.5 sec
On
On
On
On
Optional Setting - III Optional Setting - IV
Low Threshold Tach
Method
5 Sec. Delay 15 Sec. Delay
Double Pulse Triple Pulse
45 Min 3 Min
No Connection – No Connection – 1.5
Voltage Sensing Second Crank Not for
Not for Manual Manual Transmissions
Transmissions V.1 or greater
+0.6 Seconds to Crank
(-)0.2 Second Crank
Time
Time
(Voltage Sensing Only)
Optional Setting - III Optional Setting - IV
Auto
Anti-Grind +
Passive Starter Kill
On
On Lock, Unlock, and On Double Lock and
Start Start

CM5000 Wiring Schematic (Alarm and Remote Start)

The CM5000 is the control module for all alarm and remote start combo units. This controller is universal
regardless of remote or antenna type.
CN9
( - ) Switch 3 Gray 1 Red
Plug In
LED/Valet
( + ) Led 2 Gray 3 Red / White
Switch
CN1
(N/A on
( - ) Ground 1 Gray / Black 5 Violet
V.SF)
7 Green and
Red
2 Black /
LED ( + )
CN5
White
LED
LED ( - ) 1 Black
CN2
LED 4 Yellow ADS Blade Connector
(20 Pin Harness)
CN7
( + ) 3 Red
RPS
Knock 2 White
Sensor
1 Green /
( - ) 1 Black
White
3 Red / Black
5 Green
( - ) 4 Black 7 White / Black
CN3
( + ) 3 Red 9 Black
CN8
Antenna
TX 2 White 11 Orange
13 Orange /
RX 1 Yellow
White
15 White
17 Violet
1st Stage Shock 4 Yellow
( + ) 3 Red
CN6
2nd Stage
Shock
2 White
Shock
Sensor
( - ) 1 Black
CN4
1st Stage 4 Grey / White
CN10
( + ) 3 Red
Optional
2 Black / Sensor
2nd Stage
White
Input
( - ) 1 Black
CN12
RS232
2 Black
CN11
1 Black / Thermistor
White
Blade Cartridge Slot - Please
Green/White Loop
visit
Cut=Auto Trans. Uncut=Manual
www.idatalink.com/compustar
Trans.
for compatibility and more
information. This slot is empty
and has a plastic cover that slides
( + )
off.
IMPORTANT: Manufacturer or
seller will have no responsibility for
any injuries and/or damages
caused by improper care of the
( + )
product such as decomposition,
Jumpers
conversion, and transform done by
a user voluntarily
Default
( + ) Parking
Lights
Default
2 Green / White 1: ( + ) 12v Constant 2: ( + ) Parking Light
3: ( + ) 12v Constant (Separate
4 White 4: ( + ) Accessory
nd
Red/White prewired to 2 Relay)
5: ( - ) When Armed prewired to 6: ( + ) Starter (prewired to Starter
6 Yellow
Starter Kill Relay Kill Relay)
7: ( + ) Ignition and (Separate Red
8 Black 8: ( - ) Ground
prewired to Starter Kill Relay)
1 Red 1: ( + ) 12v Back Up Battery
2 Black 2: ( - ) Ground Back Up Battery
Please see the installation manual This harness is not included with
for the Blade module for details. the CM5000.
2 Lt Blue 1: ( - ) Parking Lt. Output 2: ( - ) E-Brake Input
4 Lt. Blue /
3: ( - ) Starter Output 4: ( + ) Brake Input
White
6 Violet / Black 5: ( - ) Ignition Output 6: ( - ) Trunk Input
8 Red / White 7: ( - ) Accessory Output 8: ( - / + ) Door Input
10 Brown /
9: ( - ) Status Out (GWR) 10: ( - ) Glow Input/Key Sensing
White
12 Pink 11: ( - ) Rearm Output 12: ( - ) Slave/Closed Loop Input
14 Yellow /
13: ( - ) Disarm Output 14: (AC) Tach / Alternator Input
Black
16 Gray / Black 15: ( - ) Aux 1 Output 16: ( - ) Hood Input
18 Brown 17: ( - ) Aux 2 Output 18: ( + ) Siren Output
None Future use
2 Violet / White ( - ) Trunk release output
3 Orange /
( - ) Second Unlock Output
Black
4 Blue ( - ) Unlock Output
5 Blue / Black ( - ) Lock Output
None ( + ) 12v Constant Power
1 ( + )
2 ( - )
3 Data
4 Data
Every control module has this wire
intact and must be cut for automatic
( - )
Door Trigger Polarity
Default
( - )
Key Sense/Glow Plug Polarity
Trunk Release
Behavior of CN1, Pin 2
12