Subscribe to Our Youtube Channel
Related Manuals for Firstech FT820
Summary of Contents for Firstech FT820
- Page 1 FT-820 Hyundai/Kia System MODEL: RF-2W900FM-5PT Firstech, LLC. 21911 68th Ave S. Kent, WA 98032 Phone. 888-820-3690 Fax. 206-957-3330 Please visit www.compustar.com/ft820 for additional installation resources...
-
Page 2: Table Of Contents
TaRT and laRm www.firstechllc.com /ft820 | www.compustar.com/ft820 fT-820 I nsTall uIde fT-820 able of onTenTs Wiring Guide Vehicle Compatibility Chart Introduction Kit Contents Connecting and Programming the FT-820 Figure 2 Figure 3 Option Descriptions Option Descriptions Cont. Wire Detail Wire Detail Cont. -
Page 3: Wiring Guide
TaRT and laRm www.firstechllc.com /ft820 | www.compustar.com/ft820 fT-820 I nsTall uIde fT-820 IRInG uIde Legend Required for Installation May be Required for Installation - Check Vehicle Guide for More Information Thermister Port - 2 Pin Antenna and Option... -
Page 4: Vehicle Compatibility Chart
This installation manual is for the FT-820 control module. This manual is not vehicle specific. Please visit www. firstechllc.com/ft820 or compustar.com/ft820 for vehicle specific manuals. Caution: The Manufacture’s warranty will be void if this product is installed by anyone other than an authorized Firstech dealer. Firstech reserves installation support services to authorized dealers only. -
Page 5: Kit Contents
- Firstech dual stage shock sensor P/N: CompuShock The remote(s) and antenna are available in the RF blister packaging. You have the ability to pair almost any Firstech remote(s) and antenna receiver to the FT-820. This is limited to 5P LCD remotes. - Page 6 TaRT and laRm www.firstechllc.com /ft820 | www.compustar.com/ft820 fT-820 I nsTall uIde Figure 2 - FT-820 Update Program Figure 3 - Selection of FT-820 Firmware Window Copyright 2009 Firstech, LLC. Page 6...
-
Page 7: Option Descriptions
TaRT and laRm www.firstechllc.com /ft820 | www.compustar.com/ft820 fT-820 I nsTall uIde Option 2-5 and 2-6 Option 2-5 and 2-6 affect each other depending on settings. When you change option 2-5 as shown on the three tables below option 2-6 changes from Rearm output to Horn output or Aux1 output. -
Page 8: Option Descriptions Cont
2-05 Rearm / Horn / Aux1 – This option determines the behavior of the yellow wire on the 10 pin connector of the FT820. Default the wire will act as a rearm negative pulse. Option 2 changes the wire into a horn trigger wire. Option 3 changes the wire into an Aux 1 output 2-06-A Rearm Output –... -
Page 9: Wire Detail
Pin 9 Grey/Black - CAN High wire. This wire will be connected to the CAN High wire on newer Hyundai and Kia vehicles. This is strictly a data wire. Firstech recommends not using any T-Taps or scotch locks on these wires. -
Page 10: Wire Detail Cont
TaRT and laRm www.firstechllc.com /ft820 | www.compustar.com/ft820 fT-820 I nsTall uIde fT-820 eTaIl Connector: 6-Pin Ignition Harness Caution: When connecting this harness thoroughly test the wires on the vehicle with a multimeter to assure you are connecting the right output from the FT-820. Even though the colors may be the same, they may not behave the same. -
Page 11: Post Installation Checklist
Key Points to Consider Before Installation: Options must be set before installation The options for the FT-820 must be set via your computer. Please load the FT820 software to choose the vehicle make and model, set options, and program your unit before installation. -
Page 12: Remote Programming Routine
TaRT and laRm www.firstechllc.com /ft820 | www.compustar.com/ft820 fT-820 I nsTall uIde fT-820 emoTe RoGRammInG ouTIne IMPORTANT: Any and all remotes must be coded to the control module prior to performing any and all operations. STEP 1: Activate programming mode by manually turning the vehicle’s key between the Ign On and Off (or the Acc &... -
Page 13: Common Procedures
Thermistor (Temperature Sensor) Optional Every 2 Way remote - Firstech system includes an optional thermistor, which must be plugged into the 2 pin port of the control module for use. The use of the thermistor allows the 2 Way remote to display the vehicle’s interior temperature on the remote LCD (Liquid Crystal Display) as well as permitting the vehicle to start with timed Hot or Cold starting;... -
Page 14: Option Programming With Op500
STEP 3: Exit the vehicle and close the door. The vehicle’s engine should shut off upon closing the door. If the ve- hicle’s engine does not shut off, check the door trigger connection or wait for the factory dome-light to go out. The Firstech system is in reservation mode and the vehicle is ready to safely remote start. Additional Notes Reservation mode will be cancelled if the control module recognizes the vehicles door, hood or trunk opening –... -
Page 15: Option Programming With Remote
TaRT and laRm www.firstechllc.com /ft820 | www.compustar.com/ft820 fT-820 I nsTall uIde fT-820 pTIon RoGRammInG emoTe Using a remote is a timed process so read this section in its entirety before beginning. IMPORTANT: Special Option Groups cannot be programmed with a remote – the OP500 must be used. -
Page 16: Frequently Asked Questions
A: The system is in valet mode. Tap buttons (I) + (III) for 0.5 seconds while the key is in the on position. The siren chirps once every 10 seconds after I arm the system. A: There is a poor connection between the FT820 and the vehicle’s OBDII plug. Recheck your wire(s) connection. fT-820...
Need help?
Do you have a question about the FT820 and is the answer not in the manual?
Questions and answers