Sharp AR-650 Service Handbook page 36

CODE NAME
418 Charge corona wire
cleaning
449 Temporary laser running service All
mode when the laser beam
position adjustment fails. Key in
the value, press the SET key to
store or the CLEAR key to reset.
Set to 1 until copier laser unit
can be replaced. Service call
Error Codes CA3, CA4, CA5,
CA6, CAA, CAB, CAC, CAD,
CAE, CAF, or CD0.
See troubleshooting section
for additional information.
460 RADF reversing of transfer belt
during original feed to align
originals against the original stop.
461 RADF automatic detection
of the original size.
464 Correspondence for
Exposure fluetuations
480 Paper source priority
selection
481 Automatic paper source
change.
482 Paper feed retry.
483 Polygonal motor pre-running.
484 Polygonal motor stops at an
auto clear (time out) of
control panel settings.
485 Polygonal motor rotation or
stop mode.
486 Polygonal motor stop time
487 Duplexer initial alignment
operation
08 MODE
ALLOWABLE
IMAGE
MODE DEFAULT INPUT
MODE
VALUES
All 0 0-1
0 0-1
All 0 0-1
All 0 0-1
All 1 0-1
All 1 0-4
All 1 0-2
All 0 0-1
All All 0 0-2
All All 0 0-1
All All 0 0-1
All All 0-2
All 0 0-1
1 - 29
CONTENTS
0: Enabled (cleans every 2,000 copies/prints)
1: Disabled (no cleaning)
0: Normal Mode
the laser unit operates in this mode unless a
service call is indicated when the beam position
adjustment fails.
1: Continuous Mode
Set to this mode when the laser beam adjust-
ment has failed. The results of this setting
places the laser beam close to target even
though the beam position adjustment has failed.
0: Disabled 1: Enabled
0: Non-standard(Machine will not stop and prompt
operator to select copy size when non-standard
originals are used).
1: Standard(Machine will stop and prompt
operator to select copy size when non-standard
originals are used).
0: Disabled 1: Enabled
0: LT/A4 1: LCC
3: Middle drawer 4: Lower drawer
0: OFF 1: Normal
when 1 is set, a paper source becomes empty and
the same size paper is present in another source
the machine will automatically switch to that
source of paper.
0: Enabled 1: Disabled
when set to 0 the machine will only attempt to feed
the paper 1 time before display a misfeed condition.
When set to 1 the machine will attempt to feed the
paper 2 times before displaying a misfeed condition.
0: Enabled - RADF (when originals are placed in the
tray) and Exposure Glass (when RADF is lifted).
1: Disabled - Motor starts running when the
START key is pressed. This will delay the start
of copying by 30 seconds.
2: Enabled - RADF only (when originals are
placed in the tray)
Note: This code is effective only when 08-485 is set to 1.
0: Enabled - RADF and exposure glass.
1: Disabled
Note: This code is effective only when 08-485 is set to 1.
0: Rotation 1: Stop
When Code 485 is set to 1 the polygonal motor
runs all the time.
When Code 485 is to 1 the polygonal motor runs
according to the settings of Codes 483 and 486.
0: 1 minute 1: 3 minutes
Effective when 08-484 is set to 0.
0: Enabled 1: Disabled
Correct the side skew and the paper corner
folding within three copies. If default 1 is selected,
the copying speed is a little lower than normal.
PROCE-
DURE
GROUP
1
1
1
1
1
2: Upper drawer 1
3: Extended 1
1
1
1
1
2: 5 minutes 1
1
ADJUSTMENT