Sharp AR-C360P Software Installation Manual
  1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Copier
  5. AR-C360P
  6. Software installation manual
Sharp AR-C360P Software Installation Manual

Sharp AR-C360P Software Installation Manual

Sharp ar-c360p: installation guide
Hide thumbs Also See for AR-C360P:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual, Software Installation Manual

Table of Contents

Network Installation................................... 2
Windows ................................................2
Novell ....................................................7
®
Installation ............................... 8
USB Connection ......................................8
Parallel Connection ................................ 11
®
Installation ............................ 13
OS 9.2 or above .................................... 14
OS 10.2.4 or above ............................... 16
Service and Support ................................. 18
Sharp AR-C360P
Software Installation Guide
About this Guide
This guide describes the initial printer driver
installation. For more detailed information, refer to
the EFI User Software Installation Guide and EFI
Configuration Guide provided on the User
Documentation CD (CD3).
The general steps for installing the software are as
follows:
• Install the PostScript printer driver or PCL
printer driver and corresponding printer driver
files.
• Set up the printer driver to communicate with
the Fiery.
• Install Fiery utilities and user software.
Configure Fiery utilities and user software
You must also configure either a local connection
for printing directly to your printer or a network
connection for printing over a network.
A full set of user documentation, where
procedures are described in detail, is provided on
the User Documentation CD (CD3).
1
NOTE

Advertisement

Table of Contents
loading

Related Manuals for Sharp AR-C360P

Summary of Contents for Sharp AR-C360P

  • Page 1: Table Of Contents

    Software Installation Guide Table of Contents Network Installation... 2 Windows ...2 Novell ...7 ® Windows Installation ... 8 USB Connection ...8 Parallel Connection ... 11 ® Macintosh Installation ... 13 OS 9.2 or above ... 14 OS 10.2.4 or above ... 16 Service and Support ...

  • Page 2: Network Installation

    CAUTION! Do not connect this product to an uninterruptible power supply (UPS). For further information please contact your Sharp dealer or www.sharpusa.com. Be sure to use the 15A AC power cord supplied with the printer. Use of a power cord NOT...
  • Page 3 Windows (cont’d) 2 Connect the Ethernet Interface 1. Switch off the printer and computer. 2. Remove the protective cover from the network connector on the printer. 3. Connect the Ethernet cable between the print and the Ethernet hub. NOTE For more information, see the Configuration Guide on the User Documentation CD.
  • Page 4 The LPR Utility is automatically installed with the network printer driver. To discover the printer, do the following: 1. Click Start → Programs → Sharp → LPR Utility. 2. Click Remote Print. Then, click Add Printer. 3. Select your printer model from the drop-down...
  • Page 5 > Fiery Printer Delete > Fiery Downloader > Fiery ColorWise Pro Tools NOTE If the computer will not be used by an AR-C360P administrator, Command WorkStation may not be required. 7 Activating Printer Options After you have completed the printer driver installation, you must configure the printer for the installed options.
  • Page 6 Windows (cont’d) 5. Select Two-Way Communications. 6. Type the Fiery IP address or DNS name. 7. To display the printer’s current default settings when opened, select Update Fiery Driver When Opened 8. Click Update. Click OK. 8 Install the User Documentation 1.

  • Page 7: Novell

    Novell 1 Install the Utility This utility installs, configures, and manages Sharp network print server devices. 1. Insert the printer driver CD (CD1) into your CD-ROM drive. The CD will autorun. If it doesn’t autorun, click → → Start Browse. Browse to your CD-ROM drive.

  • Page 8: Windows ® Installation

    Windows Installation USB Connection 1 Connect the USB Cable For connection to a PC running Windows 98 or above Requires a USB cable version 2.0 or above. Printer operation is not assured if a USB compatible device is connected concurrently with it. 1.
  • Page 9 Windows Installation USB Connection (cont’d) NOTE If New Hardware Found Wizard displays: Win 98: Select “Search for the best driver for your device”. Click Next. Select CD-ROM drive, clear other choices. Click Next twice. Win XP and Win Me: Select “Install the software Automatically”...
  • Page 10 Windows Installation USB Connection (cont’d) 5 Install the User Documentation 1. Insert the User Documentation CD (CD3) into your CD-ROM drive. The CD will autorun. If it doesn’t autorun, click → → Start Browse. Browse to your CD-ROM drive. Double-click Install.exe. Click 2.

  • Page 11: Parallel Connection

    Windows Installation Parallel Connection 1 Connect the parallel Interface For direct connection to a PC This port requires a bi-directional (IEEE 1284 compliant) parallel cable. Cable must be shielded and UL and CSA approved. 1. Make sure the printer is powered off. 2.
  • Page 12 Windows Installation Parallel Connection (cont’d) 17.Click Properties → General Tab → Print Test Page. 18.Click the Print Test Page button. To Install the PCL Printer Driver as Well NOTE If you have installed the PostScript driver, you must reboot your system. Follow the instructions to install the PostScript driver.

  • Page 13: Macintosh ® Installation

    Macintosh Installation Network Interface Connection IMPORTANT! Before connecting the network cable, install the Ferrite Core. See “1 Install the Ferrite Core” on page 2. ® • Requires Mac OS 9.2 or 10.2.4, and above, running on a Macintosh computer with EtherTalk interface.

  • Page 14: Os 9.2 Or Above

    1. Turn the printer ON, then turn the computer 2. Place the driver CD (CD1), supplied with the printer, in the CD-ROM drive. 3. Double-click the Sharp CD icon that appears on the desktop. 4. Double-click the MAC icon. 5. Double-click the MAC OS 9 folder.
  • Page 15 Macintosh Installation OS 9.2 or above (cont’d) 3 User Documentation For additional information on using printer features as well as printer utilities, see the on-line documentation. Requirements • Microsoft Internet Explorer version 4.0 or higher and Acrobat Reader. To Load 1.

  • Page 16: Os 10.2.4 Or Above

    1. Turn the printer ON, then turn the computer 2. Place CD 1, supplied with the printer, in the CD-ROM drive. 3. Double-click the Sharp CD icon that appears on the desktop. 4. Double-click MAC icon. 5. Double-click the OS X icon.
  • Page 17 Note: To select the Finisher Option, 4 or 5 trays must first be selected. 3 Install the Fiery EFI Utilities 1. Place CD2 in the CD-ROM drive. 2. Double-click the Sharp CD icon that appears on the desktop. 3. Double-click the MAC icon. 4. Double-click User Software.

  • Page 18: Service And Support

    • Consult the Sharp Authorized Dealer where you purchased your printer. • To find the authorized Sharp servicing dealer closest to you, please vist us on-line at www.sharpUSA.com.
  • Page 19 Trademarks Adobe and PostScript are trademarks of Adobe Systems, Inc. Which may be registered in certain jurisdictions. Microsoft, Internet Explorer and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and other countries. Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corporation. Apple, Macintosh, Mac and Mac OS are registered trademarks of Apple Computer.
  • Page 20 Finisher Unit Installation Guide Components Finisher Unit Inverter Stand Finisher stand Clear Band Finisher Stacker Band Stopper, Small Finisher Cover Band Stopper, Large Power Cord Metal Brackets Inverter Unit Cable (inverter to printer) Not illustrated: Screws Step 1: Prepare the Printer 1.
  • Page 21 3. Install the metal brackets where the breakout panels were. 4. Open the face-up stacker ( the flap and press it onto the stacker surface " 5. Close the stacker. Step 2: Prepare the Inverter Before assembling the finisher, you must adjust the height of the inverter unit to match the finisher: "...
  • Page 22 2. Remove the two bottom caps: a. Turn the inverter over. b. Remove the two screws securing the bottom caps on either side of the inverter. c. Remove the end caps and store them along with the four screws in case you ever need to convert the unit back.
  • Page 23 5. Pull forward on the extension plate to disengage the pins from the top channel stops, then slide it down into the inverter and push back to engage the pins on the bottom channel stops. 6. Reattach the extension plate using the screws you removed earlier.
  • Page 24 2. Attach the front of the inverter to the stand using two screws on either side. 3. Attach the back of the inverter to the stand using one screw on either side. 4. Attach the guard rail on the inverter stand to the printer using 2 screws.
  • Page 25 3. Place the finisher cover near the back of the finisher. Locate the tab ( ) on the right side of the cover. 4. Hold the clear band perpendicular to the cover and slip one end over the tab ( "...
  • Page 26 8. Pull the finisher platform about half way out, then loosen the screw on the locking piece ( viewed from the opposite direction) so that it drops through the slot below it. This keeps the platform from moving while you attach the finisher to it.
  • Page 27 12. Secure the stacker with four screws. 13. Push the finisher against the printer until the prongs on the printer brackets fit into the holes in the finisher. If you need to, turn the levellers ( Note: either side of the finisher to raise or lower it so the holes and prongs align properly.
  • Page 28 Application Notes & Tips Using the Single Staple Feature There is a Staple dropdown selection within the Finishing Properties of the Fiery. There are 4 single staple options within that dropdown. The choices are: • Top Left Horizontal • Top Left Vertical •...
  • Page 29 Saddle Stitching on Tabloid Paper This section explains how to saddle stitch on Tabloid size paper, using the Postscript Driver (PS) and MS Word as an example. 1. Click File then Page Setup. 2. Under Page Setup click on the Paper tab. Choose the correct Paper size.

Table of Contents