1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Copier
  5. AR-651
  6. Operation manual

Sharp AR-651 Operation Manual

Digital copying machine
Hide thumbs Also See for AR-651:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Handbook
MODEL
AR-651
AR-810
DIGITAL COPYING MACHINE
OPERATION MANUAL

Advertisement

Table of Contents
loading

Related Manuals for Sharp AR-651

Summary of Contents for Sharp AR-651

  • Page 1 MODEL AR-651 AR-810 DIGITAL COPYING MACHINE OPERATION MANUAL...
  • Page 2 To protect against loss or theft, record and retain for reference the copier’s serial number located on the left hand side at the rear corner of the copier. Model Number Serial Number Date of Purchase Place of Purchase Authorized Sharp Copier Service Department Number ➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣ ” to indicate power “ON” and...

  • Page 3: Fcc Notice

    FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
  • Page 4 The default time for the 'Off Mode' is 90 minutes. 'Automatic Energy Save'- The copier consumes less than 255 watts (AR-651)/ 316 watts (AR-810) while in Energy Save Mode. 'Automatic Energy Save' Default Time- The default time before switching to 'Automatic Energy Save Mode' is 15 minutes.

  • Page 5: Preface

    Advice ... Describes an operation you should follow to keep the digital copier in good working order. User Safety This Sharp digital plain paper copier does not produce laser radiation hazardous to the user. It is certified as a Class 1 laser product under the U.S. Department of Health and Human Services (DHHS) Radiation Perfor- mance Standard according to the Radiation Control for Health and Safety Act of 1968.
  • Page 6 The AR-651/810 also has the following convenient features, functions and options. The copying speed is 65 copies (LT) per minute for the AR-651 and 81 copies (LT) per minute for the AR-810.

  • Page 7: Table Of Contents

    TABLE OF CONTENTS Preface ... 1 Features of the AR-651/810 ... 2 Table of contents ... 3 Disclaimer notice ... 6 Precautions ... 7 1. Installation ... 7 2. General precautions ... 8 1. Before making copies ... 1-1 1. Description of the digital copier and the optional equipment ... 1-2 - Main components ...

  • Page 8: Table Of Contents

    TABLE OF CONTENTS (Cont.) 4.Using the editing functions ... 4-1 1. Image shift ... 4-2 2. Edge erase ... 4-4 3. Dual-page ... 4-5 4. X-Y zoom ... 4-7 5. Image editing ... 4-8 - Trimming/Masking ... 4-8 - Mirror image ... 4-10 - Negative/Positive reversal ...
  • Page 9 7. When the graphic symbols flash on the touch panel ... 7-1 1. Description of the flashing graphic symbols ... 7-2 2. Add paper symbol ... 7-3 - Adding paper to the drawers ... 7-3 - Adding paper to the Tandem LCF (Large Capacity Feeder) ... 7-4 - Adding paper to the External LCF (Lage Capacity Feeder) (optional) ...

  • Page 10: Disclaimer Notice

    Product even if SHARP Corp. is advised of the possibility of such damages. SHARP Corp. shall not be liable for any loss, cost, expense, claim or damage caused by any inability to use (including, but not limited to failure, malfunction, hang-up, virus infection or other problems) which arises from use of the Product with hardware, goods or software which SHARP Corp.

  • Page 11: Precautions

    Never ground it to a gas pipe, a water pipe, or any other object not suitable for grounding. After a suitable place has been selected for installation of the AR-651/810, please do not change it. Avoid excessive heat, dust, vibration and direct sunlight. Also, provide proper ventilation as the copier emits a small amount of ozone.

  • Page 12: General Precautions

    • If the copier has been exposed to rain or liquid. It is recommended that only supplies made or designated by Sharp be used for the AR-651/810 in order to optimize copy quality. All supplies should be stored in a cool, dry area.
  • Page 13 Explanatory Label > < CLASS 1 LASER PRODUCT APPAREIL A LASER DE CLASSE 1 LASER KLASSE 1 PRODUCTO DE LASER DE CLASE 1 Certification Label Warning Label Warning for high temperature areas Identification Label > <...
  • Page 14 PRECAUTIONS (Cont.) 2. General Precautions (Cont.) Fixing the adjusters (stoppers) There are four adjusters (stoppers) located in front and rear bottom (two adjusters each) of the copier. After moving/ installing the copier, be sure to turn the adjusters clockwise to fix them firmly on the ground. *To unlock the adjusters when moving the copier, turn them counterclockwise.
  • Page 15 1. BEFORE MAKING COPIES 1. Description of the digital copier and the optional equipment ... - Main components ... 1-2 - Optional equipment ... 1-3 - Control panel ... 1-4 - Touch panel ... 1-6 2. Turning ON the power switch ... - Turning ON the Power Switch/Auto Job Start ...

  • Page 16: Before Making Copies

    1. DESCRIPTION OF THE DIGITAL COPIER AND THE OPTIONAL EQUIPMENT Main Components Original scales Control panel Drawers Paper size indicator Operator’s manual pocket (Back side) Power switch Exit cover Toner cartridge BEFORE MAKING COPIES Reversing automatic document feeder Front cover Transfer unit Original glass Bypass cover...

  • Page 17: Optional Equipment

    (Available when the optional staple sorting and the hole punch mode units are installed.) This paper is not run through fuser (heat). External LCF ( Large Capacity Feeder) Feeds up to 4000 sheets of LT-sized paper (20lb. Bond)(recommended by Sharp) continuously. Optional Equipment Configuration Finisher...

  • Page 18: Control Panel

    1. DESCRIPTION OF THE DIGITAL COPIER AND THE OPTIONAL EQUIPMENT (Cont.) Control Panel Total Counter Shows the total of copied paper since the set up of the copier. HELP key When this key is pressed, the appropriate operation procedures are displayed. PRINTER/NETWORK key Press this key to switch between the printer and the network (optional) functions.
  • Page 19 CLEAR ALL key When this key is pressed, all selected copy modes are cleared to default settings. * Automatic CLEAR ALL Right bottom of this page STOP key Use this key to stop an ongoing scan and copy operation. START key Press this key to start copying.

  • Page 20: Touch Panel

    1. DESCRIPTION OF THE DIGITAL COPIER AND THE OPTIONAL EQUIPMENT (Cont.) Touch Panel When the power is turned on, and ‘READY’ is displayed, the following basic screen is shown on the touch panel. On the screen, currently set functions, selected functions and the copier status are shown using messages and illustrations.
  • Page 21 - SETTINGS (set functions confirmation) key This key allows you to confirm the functions that have been set. (The display shown on the right is an example.) The icons displayed on the screen are as follows(some icons may not appear on the screen): Clearing the Functions Selected If you press any key that is half-tone shaded, the function selected is cleared.

  • Page 22: Turning On The Power Switch

    - This message appears on the message panel of the Basic Screen: Wait Warming Up - Time of warming up AR-651/810: Approx. 160seconds When “READY” appears, the copier is ready for copying. While the copier is warming up, place the original on the glass, select the desired copy modes and press the copier starts scanning the originals.

  • Page 23: Controlling The Use Of The Copier With Account Numbers

    Controlling the Use of the Copier with Account Numbers With the use of account numbers, you can restrict copier users as well as manage copy volumes made by individual groups or departments of your company. * Registering, changing and deleting a account number When the account number function is in use, the screen shown on the right appears immediately af- ter the power switch is turned on or the auto-clear is...

  • Page 25: How To Make Copies

    2. HOW TO MAKE COPIES 1. General copying procedures ... 2. Setting copy paper ... - Acceptable copy paper types and sizes ... 2-4 - Handling and sorting paper ... 2-5 - Changing the paper size of the drawer / Setting the drawer for special uses ...2-6 3.

  • Page 26: General Copying Procedures

    1. GENERAL COPYING PROCEDURES After placing, or confirming that there is, paper in the drawers, place the originals. When the is pressed with any settings unchanged, copies are made in the initial (default) settings * copies as desired by setting different copy modes. The initial (default) settings of the copier at the time of installation are as shown below.
  • Page 27 Once the final original has been scanned, press the FINISHED key. - When the reversing automatic document feeder is used, and the single-feed mode is selected, the procedure is slightly different from the above. Procedure of using the single-feed mode - After starting copying, press the JOB STATUS key on the control panel, then press the STATUS key on the touch panel to indicate which drawer is in use.

  • Page 28: Setting Copy Paper

    - The following sizes of paper can be used for hole punch: LG, LT-R (2 holes, 0.315" diameter), LD, LT, A3, A4 ( 3 holes, 0.315" diameter) - “Maximum capacity” refers to the number of sheets when the paper recommended by Sharp is set. HOW TO MAKE COPIES...

  • Page 29: Handling And Storing Paper

    Handling and Storing Paper Pay attention to the following points: - Avoid using paper that is specially treated or paper that was printed on another machine, and also avoid performing double copying on the same side of paper; this may cause a malfunction. - Do not use paper with creases, wrinkles, curled paper, paper prone to curling, smooth paper, or tough paper;...

  • Page 30: Changing The Paper Size Of The Drawer/Setting The Drawer For Special Uses

    2. SETTING COPY PAPER (Cont.) Changing the Paper Size of the Drawer/Setting the Drawer for Special Uses The paper size of the drawers of the copier can be changed to desired size. The drawers can also be set for cover sheet, insertion, tab paper, thick paper and special sheets. Changing the Paper Size of the Drawer Pull out the drawer toward you.
  • Page 31 Press the JOB STATUS key on the control panel, then the CASSETTE key on the touch panel. Press the drawer key corresponding to that in which the paper size has been changed, then press the key of the paper size newly set. - Chinese paper sizes (16K, 8K and 16K-R) can be selected on the screen which appears when the Next key is pressed once.
  • Page 32 2. SETTING COPY PAPER (Cont.) Changing the Paper Size of the Drawer/Setting the Drawer for Special Uses(Cont.) Press the drawer key corresponding to that in which the paper has been set, then press the key of the paper type newly set. - If you want to select the COVER , INSERT , or TAB , make sure that paper with the same size as that for the COVER, INSERT, or TAB PAPER is set in the other drawer including...

  • Page 33: Setting Originals

    3. SETTING ORIGINALS Acceptable Original Types and Sizes Setting place Glass Sheets Three-dimensional objects Books Reversing automatic Plain paper, recycled paper: document feeder 13.3 - 33.8 lb. (1-Sided Original) 13.3 - 27.7 lb (2-Sided Original) *1 Do not place any heavy object (8.82 lb. or over) on the glass. *2 Even listed under “Types of originals”, some of the originals may not be used depending on paper quality.

  • Page 34: When Placing An Original On The Glass

    3. SETTING ORIGINALS (Cont.) When Placing an Original on the Glass Sheet Originals When using the non sorting and non staple mode, the paper exits face up. Raising the reversing automatic document feeder, place the original face down on the glass. Align the original against the left inner corner of the glass.

  • Page 35: When Using The Reversing Automatic Document Feeder

    When Using the Reversing Automatic Document Feeder Precautions for Using the Reversing Automatic Document Feeder Do not use the following types of originals as they tend to misfeed or become damaged: (1) Badly wrinkled or folded originals; in particular, originals whose leading edge is curled may fail to be correctly fed.
  • Page 36 3. SETTING ORIGINALS (Cont.) When Using the Reversing Automatic Document Feeder (Cont.) In the Continuous Feed Mode - Be sure to set only originals with the same size. Mixed-sized originals After aligning the edges of originals well, place them face up and align the slides to the width of the originals. - Align the originals in the order from the top because they will be fed from the top.

  • Page 37: Auto Job Start (Job Preset)

    4. AUTO JOB START (JOB PRESET) While multi-copying is in process, you can reserve the next copy. Place the original(s). Select copy modes as required. Press the START key. - Up to 5 jobs including the current printing job can be stored in the memory.

  • Page 38: Interrupt Copying

    5. INTERRUPT COPYING While multicopying is in progress, you can interrupt it and make copies from different originals. * The following modes cannot be used with interrupt copying. - Cover sheet copying Press the INTERRUPT key. - This message appears: Job interrupted job 1 saved - Interrupt copying is available while copying is in progress.

  • Page 39: Stopping The Copy Operation

    6. STOPPING THE COPY OPERATION If you want to stop the operation during scanning or multicopying, use the Stopping the Scanning of the Original Press the control panel STOP key on the operational panel during the scanning. If the screen on the right appears, press the MEMORY CLEAR key.

  • Page 40: Deleting Or Changing Order Of Pending Jobs

    7. DELETING OR CHANGING ORDER OF PENDING JOBS If data is waiting to be printed, you can delete them, or change the printing order. Deleting the Job In the following procedure, you can delete the multicopying operation as well. Press the JOB STATUS key on the control panel, then the JOB LIST key on the touch panel.
  • Page 41 Changing the Printing Order Press the JOB STATUS key on the control panel, then the JOB LIST key on the touch panel. Select the job you want to move. Press the MOVE key, then press the position where the selected job is to move to. - The job to be moved will be shifted next to new priority.

  • Page 43: Setting Of Basic Copy Modes

    3. SETTING OF BASIC COPY MODES 1. Paper selection ... - Automatic paper selection (APS) ... 3-2 - Manual paper selection ... 3-3 2. Reduction and enlargement copying ... 3. Duplex copying (1-sided, 2-sided, book-type) ... 4. Copy density adjustment ... 5.

  • Page 44: Paper Selection

    1. PAPER SELECTION Automatic Paper Selection (APS) When you place regular-sized originals on the glass or in the reversing automatic document feeder, the built-in sensors automatically work to detect the size of the originals, helping the copier select and copy on paper that is the same size as the original.

  • Page 45: Manual Paper Selection

    Manual Paper Selection It may not be possible for the device to perform Automatic Paper Selection with highly transparent originals such as OHP films and tracing paper, wholly dark originals or originals with dark borders, or irregular sized originals such as newspapers and magazines. For these types of originals, use manual paper selection. * When the desired size of paper is not set in any of the drawers, you can change the paper size of the drawer ( Page 2-6) or use the sheet bypass copying (...

  • Page 46: Reduction And Enlargement Copying

    2. REDUCTION AND ENLARGEMENT COPYING When placing originals on the glass, you can copy them at the reducing and enlarging rate of 25 to 400%. For the reversing automatic document feeder, you can make the copy at the reducing and enlarging rate of 25 to 200%.
  • Page 47 Specifying both Original Size and Copy Size Place paper in the drawer(s). Place the original(s). Press the desired drawer, then the ZOOM··· key. - The copy paper size is selectable on the screen in step 4 as well. Press the ORIGINAL SIZE key of the same size as the original.
  • Page 48 2. REDUCTION AND ENLARGEMENT COPYING (Cont.) Using the Reduction / Enlargement Zoom Keys or One-touch Zoom Keys Place paper in the drawer(s). Place the original(s). Press the drawer icon representing the desired copy paper size, then press the ZOOM···· key. - The copy paper size is selectable on the screen in step 4 as well.

  • Page 49: Duplex Copying (1-Sided, 2-Sided, Book-Type)

    3. DUPLEX COPYING (1-SIDED, 2-SIDED, BOOK-TYPE) This function allows you to set the type of originals (1-sided, 2-sided or book-type) and the desired type of copying (1-sided or 2-sided). -12- can not be used by OHP film. Original Copy -15- -12- -13- -13-...
  • Page 50 3. DUPLEX COPYING (1-SIDED, 2-SIDED, BOOK-TYPE) (Cont.) Place paper in the drawer(s). - When using the mode of 1-Sided Originals to 2-Sided Copies and 2-Sided Originals to 2-Sided Copies in bypass copying, be sure to specify the paper size. Place the original(s). Press the key (shaded) on the right basic screen.
  • Page 51 Press the BOOK 2 key. Select the book copying type. - Press the RIGHT RIGHT key if copying should start at a right-hand page and end at a right-hand page. By the same token, you can choose from among the RIGHT LEFT LEFT and LEFT Select LT copy size.
  • Page 52 3. DUPLEX COPYING (1-SIDED, 2-SIDED, BOOK-TYPE) (Cont.) Turn to the next page, set the book again and press START key. - Repeat the procedure above until all your originals have been scanned. After all your originals have been scanned, press the FINISHED key.

  • Page 53: Copy Density Adjustment

    4. COPY DENSITY ADJUSTMENT There are two types of image density adjustments: automatic mode (default setting) and manual mode. In the automatic mode, the sensors automatically detect the density of each original and select the optimum image density. In the manual mode, you can select the desired level of image density. It is recommended that lighter-density original be coped in the manual copy density mode.
  • Page 54 4. COPY DENSITY ADJUSTMENT (Cont.) Manual Copy Density Mode Place paper in the drawer(s). Place the original(s). Press AUTO on the basic screen. Press either to the desired level. - Each time you press the lighter or darker, respectively. - When the DENSITY LEVEL key is shown on the lower left of the screen, you can adjust the density manually on the basic screen.

  • Page 55: Selecting Original Mode

    5. SELECTING ORIGINAL MODE According to the type of your originals, you can choose among the three image types: Photo, Text or Text/ Photo (default setting). The Photo mode is suitable for copying photo originals whereas the Text mode is preferable for copying originals containing text only (or text and line artwork only).

  • Page 56: Quick Access Menu

    6. QUICK ACCESS MENU Finishing copy and duplex modes can be performed at the same time on one display by pressing the QUICK button. The character and button sizes are enlarged, and the white characters are displayed on the black background in order that you can easily operate the copier. Place paper in the drawer(s).

  • Page 57: Using The Editing Functions

    4. USING THE EDITING 1. Image shift ... 2. Edge erase ... 3. Dual-page ... 4. X-Y zoom ... 5. Image editing... - Trimming/Masking ... 4-8 - Mirror image ... 4-10 - Negative/Positive reversal ... 4-11 6. 2 IN 1 / 4 IN 1 ... 7.

  • Page 58: Image Shift

    1. IMAGE SHIFT A margin for binding is created by shifting the original image to either the right or left side. You can also create binding margins in the center (inner margin) when using Book-Type Originals to 2-sided copies( Page 3-8). Providing Right or Left Margin Place paper in the drawer(s).
  • Page 59 Adjust the width of the binding margin, then press the SET key. - The default width of the margin is 7mm (0.276"). - To adjust the width, press the select the desired number, then press the SET key. - In duplex copying, margins on the back are created on the other side of those in the front.

  • Page 60: Edge Erase

    2. EDGE ERASE If your original has a dirty or torn edge, it may be reproduced as a black mark on the copy. In that case, use Edge Erase Copying. A white border is created along the edges of the copy, eliminating those black marks. * This function is available in only case of the standard-size original.

  • Page 61: Dual-Page

    3. DUAL-PAGE Utilizing this feature allows the facing pages of a book or magazine to be copied page by page onto two separate sheets of paper or duplex-copied on one sheet. There is no need to move the original on the glass. You can also place a pair of LT (or A4, B5) sized originals side by side and copy them on separate sheets of paper.
  • Page 62 3. DUAL PAGE (Cont.) Place the first page(s) to be copied on the glass, and press the - If you do not copy your originals from the first page, the cop- ies will not be arranged in the same order as the original. - Center the book on the yellow indicator line with the bottom toward you.

  • Page 63: X-Y Zoom

    4. X-Y ZOOM You can make copies with different reproduction ratios set for the X (horizontal) and Y (vertical) directions, respectively. 100% Place paper in the drawer(s). Place the original(s). Press the EDIT key to enter the edit menu, and press the XY ZOOM key.

  • Page 64: Image Editing

    5. IMAGE EDITING Trimming/Masking You can select an area on an original and copy it with the area trimmed (only the inside of the area copied) or masked (only the outside of the area copied). Four rectangular areas can be specified on an original. * Image editing is only possible with standard sized originals.
  • Page 65 Place an original on the glass to specify the area. - Set the original face up with the bottom toward you, fit its top left corner against the top left corner of the glass, and align it with the original scale. Using the original scale on the left and the inner (top) scale, read the position of the desired area as follows:...

  • Page 66: Mirror Image

    5. IMAGE EDITING (Cont.) Mirror Image Copies are made with images completely reversed in terms of right and left. Place paper in the drawer(s). - When using this mode in bypass copying , be sure to specify the paper size. Place the original(s).

  • Page 67: Negative/Positive Reversal

    Negative/Positive Reversal The white area of originals copying black, and the black area of originals copying white. Place paper in the drawer(s). Place the original(s). Press the EDIT key to enter the edit menu, and press the EDITING key. Press the NEG/POS key. Select other copy modes as required.

  • Page 68: In 1 /4 In 1

    6. 2 IN 1 / 4 IN 1 This feature allows multiple originals to be reduced and copied onto a single sheet which size is the same size as the original. There are two modes: 2 IN 1 copying, where two originals are reduced and copied onto a single sheet, and 4 IN 1 copying, where four originals are reduced and copied onto a single sheet.
  • Page 69 Place paper in the drawer(s). - When using this mode in bypass copying, be sure to specify the paper size. Page 5-10, 5-11 To make copies onto paper which is not the same size as originals, press the ZOOM... key to enter the right menu, and press the size you desire and the AMS key.

  • Page 70: Copying With Annotation

    7. COPYING WITH ANNOTATION Copies are made with the current date and time, at which they are made, printed on the copy. Date and time printed at the bottom of the portrait copy Place paper in the drawer(s). Place the original(s). Press the EDIT key to enter the edit menu, and press the ANNOTATION key.

  • Page 71: Page Numbering Copying

    8. PAGE NUMBERING COPYING This feature allows numbers to be added at specified position to copies. Page number printed at the bottom center on the portrait copy. Place paper in the drawer(s). Place the original(s). Presse the EDIT key to enter the edit menu, and press the PAGE NUMBER key.

  • Page 72: Magazine Sort (From The Editing Menu)

    9. MAGAZINE SORT (FROM THE EDITING MENU) The magazine sort mode allows 1-sided originals to be copied and sorted so that they can be folded and bound along a center line like typical magazines or booklets. Example of copying a 12-page document •...
  • Page 73 Adjust the binding margin and press the SET key. - The default width of the margin is 2 mm (0.08"). - To adjust the width, press the select the desired number, then press the SET key. - If the optional saddle stitch finisher (AR-F12) is installed, copies can be automatically stapled along their center line.

  • Page 74: Cover Copying

    10. COVER COPYING A top cover and/or back cover (special sheets, e.g. colored paper) can be added to each set of copies. - Adding a blank cover - Adding a copied cover - Adding a blank cover and a blank back cover - Adding a copied cover and blank back cover Example of adding a blank cover Example of adding a copied cover...
  • Page 75 Press the EDIT key to enter the edit menu, and press the COVER SHEET key. - If the desired function keys are not displayed, press the Next or Pre key to change the menu screen. Select the desired cover sheet key: To add a blank top cover: TOP BLANK To add a copied top cover: TOP COPIED To add blank top and back covers: BOTH BLANK...

  • Page 76: Sheet Insertion Copying

    11. SHEET INSERTION COPYING Special sheets of paper (such as colored paper) are inserted into a set of copies at specified pages. There are two sheet Insertion modes available: - Inserting blank sheets before specified pages - Inserting copied sheets at specified pages Example of inserting a blank before the specified page Example of inserting a copied sheet...
  • Page 77 Press COPIED or BLANK key. To insert copied sheets at specified pages: COPIED To insert blank sheets before specified papers: BLANK Key in the desired page number (no more than 3 digits) for insertion and press the upper SET key. - On the display, the page where the first sheet will be in- serted is shown.

  • Page 78: Tab Paper Mode

    12. TAB PAPER MODE Tab paper copy and insertion are available. Tab Paper Copy: Copying on tab paper Tab Paper Insertion: Inserting blank tab paper prior to a selected page Tab Paper Insertion and Copy: Combination of copying on tab paper and inserting tab paper - To copy on tab paper, adjust the tab width.
  • Page 79 Setting Tab Paper in the Bypass Guide Align the tab paper with the original. Originals Place the tab paper with face up on the bypass guide. Perform step 3 and 4 on page 5-9. -Be sure to select ‘Tab Paper’ for the paper type. Tab Width Adjustment To copy on tab paper, adjust both the tab width and the shift width for the drawer and the bypass guide respectively.
  • Page 80 12. TAB PAPER MODE(Cont.) Press the TAB EXTENSION key. Press the CASSETTE key (or the BYPASS FEED key), then adjust the tab extension (tab width) and the shift width then press the SET key. - Adjust the tab width and the shift width by means of 0mm key and the 30mm Unless the tab width has refreshed, the previous value is valid.
  • Page 81 Tab Paper Copying Copyng on tab paper at the value in the tab width set mode ( Place tab paper in the drawer or the bypass guide. - For placing it in the drawer - For placing it in the bypass guide Place the original(s).
  • Page 82 12. TAB PAPER MODE(Cont.) Tab Paper Insertion Tab paper (blank) is inserted prior to selected pages. Up to 15 sheets of tab paper can be inserted. Place tab paper in the drawer or the bypass guide. - For placing it in the drawer - For placing it in the bypass guide Place the original(s).
  • Page 83 Tab Paper Insertion and Copying - Copied tab paper is inserted prior to the selected pages. Up to 15 sheets of tab paper can be inserted. Place tab paper in the drawer or the bypass guide. - For placing it in the drawer - For placing it in the bypass guide Place the original(s).

  • Page 84: Document Storage

    13. DOCUMENT STORAGE This feature allows images of the originals to be stored on the hard disk of the copier, and copies can be made from the hard disk later. This copying method consists of the following two modes: MEMORIZE mode: Stores original images at the specified location of the hard disk. PRINT mode: Prints the originals stored in the Memorize Mode in * Originals can be stored in up to 24 locations.
  • Page 85 Press the START key. - The memorization process starts automatically. - To change the file name, select the ID you want to change in the list on the display, press the file name column, delete the file name already entered with the B Space key in the letter entry screen, then enter a new file name, and press the SET key.

  • Page 86: Overlay

    14. OVERLAY This function stores the images that you frequently use and makes copies by overlaying onto the copied originals. - 24 different images can be stored. * The original can be overlaid with the stored image of the same size and in the same orientation. (It cannot be adjusted with reduction and enlargement.) Storing Image Place the original you want to have memorzied.
  • Page 87 Input the file name with the screen for entering letters and press the SET key. - Entering letters. Page 5-28 Press the START key. -The original starts scanning to memorize the image. The form will be stored as shown on the right. Confirming Stored Image (Test Print) Perform steps 2 and 3.
  • Page 88 14. OVERLAY (Cont.) Overlaying Originals with Stored Image Place paper in the drawer(s). Place the original(s). Press the EDIT key to enter the edit menu, and press the OVERLAY key. - If the desired function keys are not displayed, press the Next key to change the menu screen.

  • Page 89: Sharpness Adjustment

    SHARPNESS key. - If the desired function keys are not displayed, press the Next key to change the menu screen. Press the SOFT ( or SHARP - Pressing the SOFT key suppresses the moire fringe while pressing the SHARP and sharpens the fine lines.

  • Page 90: Direction Of Duplex Images (Rotation)

    16. DIRECTION OF DUPLEX COPY IMAGES (Rotation) When lengthwise LD, A3, A5 or B4 paper is copied under the mode of 1-Sided Originals to 2-Sided Copies, 2-Sided Originals to 1-Sided Copies, this function allows you to adjust the direction for ‘side-by-side’...
  • Page 91 5. USING THE SPECIAL 1. Continuous original feeding / Single original feeding ... 2. Mixed-sized originals ... 3. Job memory ... 4. Bypass copying ... - Bypass copying on standard size paper ... 5-10 - Bypass copying on non-standard size paper ... 5-11 5.

  • Page 92: Using The Special Functions

    1. CONTINUOUS ORIGINAL FEEDING / SINGLE ORIGINAL FEEDING When using the reversing automatic document feeder, you can select the continuous feed mode (default setting) where multiple (or single) originals are continuously fed in one by one, or the single-feed mode where if you insert an original, it is automatically pulled in and starts being copied.
  • Page 93 Single-feed Mode Place paper in the drawer(s). Press the PROGRAM key to enter the program menu, and press the ADF key. Press the SADF key. Select other copy modes as required. Place an original. Page 2-9 - The original is automatically pulled in and the screen changes as shown on the right.

  • Page 94: Mixed-Sized Originals

    2. MIXED-SIZED ORIGINALS When placing the different-sized originals in the reversing automatic document feeder, you can make copies by setting MIXED-SIZED ORIGINALS. The available combination of mixed-sized originals are as follows: - LD, LG, LT, LT-R * The image may be copied out of position depending on the combination. Place paper in the drawer(s).

  • Page 95: Job Memory

    3. JOB MEMORY You can store and recall a combination of frequently used copy jobs at anytime. Up to four such combinations of jobs can be stored. * You cannot delete the copy modes that have already been stored in the memory, but you can rewrite new jobs on the memory key in which some copy modes have already been stored.
  • Page 96 3. JOB MEMORY (Cont.) Recalling a Stored Combination of Copy Job Settings to Make Copies Place paper in the drawer(s). Place the original(s). Press the PROGRAM menu, and press the JOB MEMORY key. Press the RECALL key. Press the Memory Number key where the desired combination of copy job settings are stored.
  • Page 97 Confirming Stored Copy Jobs To confirm the copy modes stored in the Memory Number key, perform steps 3 to 5 on the previous page, then press the SETTINGS key. - The screen on the right is an example of jobs that have been stored in “MEMORY 2”.

  • Page 98: Bypass Copying

    4. BYPASS COPYING When you want to make copies on thick paper, OHP film, tab paper, tracing paper, sticker labels, use the sheet bypass. (Only thick and tab papers can be set in the drawer. If the desired size of paper (standard size) is not set in any of the drawers, or if you want to make copies on non-standard size, make bypass copies.
  • Page 99 Place the original(s). If the paper other than standard type has been set, press the PROGRAM key to enter the program menu, and press BYPASS FEED key. - If the standard size paper has been set, you do not have to perform steps 3 to 4.

  • Page 100: Bypass Copying On Standard Size Paper

    4. BYPASS COPYING(cont.) Bypass Copying on Standard Size Paper perform steps 1 to 2 on pages 5-8, 5-9. -Set the "OTHER" size key as necessary. If the paper that has been set is a standard size other than LD, LG, LT or ST, you will select the OTHER key in step 2. In this case, you need to make the OTHER key recognize the same size as the paper that has been set.

  • Page 101: Bypass Copying On Non-Standard Size Paper

    Bypass Copying on Non-Standard Size Paper The size of non-standard paper is within the following ranges: Length: 100 - 297mm (3.94" - 11.69") Perform steps 1 to 3 on page 5-10. Press the NON-STANDARD key. Key in each dimension (length and width), or recall the data stored in the MEMORY.
  • Page 102 4. BYPASS COPYING(cont.) Bypass Copying on Non-Standard Size Paper(cont.) Storing a Non-Standard Size in the MEMORY It is convenient if a frequently used non-standard size of paper is stored in the memory. Perform steps 1 to 3 on page 5-10. Press the NON-STANDARD key.

  • Page 103: Weekly Timer

    5. WEEKLY TIMER Using the built-in weekly timer, you can have the copier automatically turned ON and OFF at specified times. For instance, you can set the timer for the starting time and closing time of your office so that the copier will automatically turn itself ON and OFF at those specified times.

  • Page 104: Setting The "Other" Size Key

    6. SETTING THE “OTHER” SIZE KEY When original or paper size is required to be specified and you need to specify it to ‘OTHER’ size (except for non-standard size), this function should be used. - This function allows the OTHER key on the screen on the right to recognize the size that will be used.

  • Page 105: Setting The Date And Time

    7. SETTING THE DATE AND TIME The clock built in to the copier can be set by entering the date, day of the week and time using the digital keys. Also, you can easily change the clock to and from the daylight saving time system at the touch of a key.

  • Page 106: Setting The Automatic Energy Save Mode

    8. SETTING THE AUTOMATIC ENERGY SAVE MODE This function allows the copier automatically to go into the energy saving mode (unnecessary electricity is cut off at standby) if it is left inactive for a certain period of time. ENERGY SAVER key Press the PROGRAM menu, and press the ENERGY SAVE key.

  • Page 107: Setting The Automatic Off-Mode

    9. SETTING THE AUTOMATIC OFF-MODE When the power of the optional printer controller is ON, the copier goes into the sleep mode which stands by with the minimun power consumption. Press the PROGRAM key to enter the program menu, and press the AUTO SHUT OFF key. - If the desired function keys are not displyed, press the Next key to change the menu screen.

  • Page 108: Switching Languages

    10. SWITCHING LANGUAGES The language used on the touch panel can be changed to a different one. Press the PROGRAM menu, and press the CHANGE LANGUAGES key. - If the desired function keys are not displayed, press the Next key to change the menu screen. Press the key of the desired language.

  • Page 109: Account Numbers

    11. ACCOUNT NUMBERS You can administer the copy quantity of each group by setting a account number for each purpose (copier and printer ). Up to 150 numbers can be set. *You need a master number to be registered when you use this function for the first time. Master number registration Press the PROGRAM key to enter the program...
  • Page 110 11. ACCOUNT NUMBERS (Cont.) Input the master number name, and press the SET key. - Entering letters Key in the desired master number (the same number) both for “NEW NUMBER” and for “RETYPE THE NEW NUMBER” , and press the SET key. - The master number is 5 digits (“00000”...

  • Page 111: Account Number

    Key in the master number or the account number (5 digits), then press SET key. - Registration of Account Number Input the master number for using “SET ACCOUNT NUMBERS” and “RESET ALL COUNTERS”. The account number menu is displayed. - The screen when the master number is entered - The screen when the account number is entered Registration / Change / Deletion of Account Number *Available only when the master number is entered.
  • Page 112 11. ACCOUNT NUMBERS (Cont.) Press the ENABLE key, then SET key. Press the account number where you want to register the account number, and press the CHANGE key. Input the account name and press the SET key. - Entering letters Key in the desired account number (the same number) both for “NEW NUMBER”...
  • Page 113 Changing a Specific Account Number Press the SET ACCOUNT NUMBERS key in the account menu. Press the ENABLE key, then SET key. Press the account number where you want to change the account number, and press CHANGE key. Press the SET key. 5-23...
  • Page 114 11. ACCOUNT NUMBERS (Cont.) Input the account name you want to register, and press the SET key. - Entering letters Key in the former account number for “CURRENT NUMBER” and the new account number both for “NEW NUMBER” and “RETYPE THE NEW NUMBER”, and press the lower SET key.
  • Page 115 Press the account number where you want to delete the account number, and press the DELETE key. Press the YES key. - Deleting of the selected account number is completed. Clearing a Specific Account Counter Press the SET ACCOUNT NUMBERS key in the account number menu.
  • Page 116 11. ACCOUNT NUMBERS (Cont.) Press the account number you want to clear the counter, and press the RESET COUNTERS key. Press the YES key. - The counter reset is completed. Disabling a Account Number Press the SET ACCOUNT NUMBERS key in the account number menu.
  • Page 117 Print out account number *This function prints out the number of copies output for each account. Press the PRINT OUT ACCOUNT NUMBERS key in the account number menu. - Printing starts. Clearing All Counters This function clears all counters to “000000”. *Available only when the master number is entered.

  • Page 118: Entering Letters

    12. ENTERING LETTERS The following screen is provided for entering letters. * To enter numbers, use the digital keys on the control panel. The following keys are used to enter letters. - CapsLock ... Press this key to switch capital letters and small letters. - B Space ...
  • Page 119 Press the E , T , I , N and G keys. Press the SET key to fix the entered letters. Correcting Entered Letters Example: Correct “Meeting” to “MEETING”. Press the B Space key to delete “eeting”. Press the CapsLock key to enter the capital letters. 5-29...
  • Page 120 12. ENTERING LETTERS (Cont.) Press the E , E , T , I , M and G keys. Press the key to move the cursor to (under) “G”. Press the B Space key to delete “M”. Press the N key to enter “N”, then the SET key to fix the entered characters.
  • Page 121 6. SELECTING FINISHING MODES (USING THE OPTIONAL FINISHERS AND INSERTER) 1. Finishing modes and finishers (optional) ... 2. Sort/group copying ... 3. Staple sorting (optional) ... 4. Magazine sort & saddle stitch mode (booklet mode) (optional) . 5. Hole punch mode (optional) ... 6.

  • Page 122: Selecting Finishing Modes (Using The Optional Finishers And The Inserter)

    1. FINISHING MODES AND FINISHERS (OPTIONAL) There are 2 types of optional finishers ( AR-F11 and AR-F12 ). Functions available differ depending on whether a finisher is installed and which type of finisher it is. - Press the key on the basic screen on the right (shaded), and confirm the finishing modes on the panel.

  • Page 123: Sort/Group Copying

    2. SORT/GROUP COPYING To make multiple copies, you can select the sort mode or group mode as necessary. The paper sizes available for sort/group copying are LD,LG,LT,LT-R,COMP,A3,A4,A4-R,B4,B5 and FOLIO. Example of making 5 sets of copies from 5-page originals - Sort copying Place paper in the drawer(s).

  • Page 124: Staple Sorting (Optional)

    3. STAPLE SORTING (OPTIONAL) When the optional finisher is installed, you can use the function that performs automatic stapling at one of the following three positions. * The paper weight should be in the range of 16lb. Bond - 28lb. Bond. Special paper such as OHP films or labels is excluded.
  • Page 125 Press the key on the basic screen as shown on the right (shaded). Press the SINGLE STAPLE-1 (or DOUBLE STAPLE , SINGLE STAPLE-2 ) key. Select other copy modes as required. Press the START key. - If the paper quantity exceeds the maximum number of sheets that can be stapled, the finisher automatically enters the sort mode.

  • Page 126: Magazine Sort & Saddle Stitch Mode (Booklet Mode)(Optional)

    4. MAGAZINE SORT & SADDLE STITCH MODE (BOOKLET MODE) When the Magazine Sort mode is selected, 1-sided originals can be copied and bound like magazines or booklets. When a finisher with a saddle stitch (optional, AR-F12) is installed, you can select the saddle stitch mode which will automatically staple in the center of the document.
  • Page 127 Press the key on the basic screen as shown on the right (shaded). Press the MAGAZINE SORT ( or MAGAZINE SORT & SADDLE STITCH or SADDLE STITCH ) key. - If the desired function keys are not displayed, press the Next key to change the menu screen.

  • Page 128: Hole Punch Mode (Optional)

    5. HOLE PUNCH MODE (OPTIONAL) With the optional hole punch unit attached to the optional finisher (AR-F11, AR-F12), you can have your copies punched with holes. * The paper weight should be in the range of 17 lb. Bond - 140 lb.Index. Special paper such as OHP films or labels is excluded.

  • Page 129: Inserter Mode (Optional)

    Plain paper (16 lb. Bond - 20 lb. Bond), Thick paper (more than 20 lb. Bond- 140 lb. Index), Paper type Recycled paper, Special paper (OHP film, Color paper, Hole punch paper, etc.) (Ask your authorized Sharp dealer for the details of acceptable special papers.) Maximum 16 lb. Bond - 20 lb. Bond : 100 sheets capacity more than 20 lb.Bond - 140 lb.

  • Page 130: Setting The Inserter

    6. INSERTER MODE (OPTIONAL)(Cont.) Setting the Inserter Blank paper placed in the optional inserter can be inserted into the pages you desire (including the front and back cover). - When placing the paper for the initial (default) setting (LD and plain paper for the initial setting of the copier at the time of installation), the procedures from step 5 to 8 are not necessary.
  • Page 131 Press the key of the paper size placed in the inserter. Press the MEDIA TYPE key. - For plain paper, skip step 7 and step 8 because these proce- dures are not necessary. Press the key of the paper size placed in the inserter, then press the RETURN key.
  • Page 132 6. INSERTER MODE (OPTIONAL)(Cont.) Setting the Inserter (Cont.) Sheet Insertion Insertion of a blank sheet prior to the selected page Press the SHEET INSERT key. Key in the page number where you wish to insert the sheet, and press the upper SET key. - When two or more sheets are inserted, repeat this proce- dure.

  • Page 133: Using Only Staple And Hole Punch

    Using only Staple and Hole Punch When installing the optional inserter, you can use only the finishing mode (staple and hole punch). In that case, set it with the control panel on the inserter side. Place paper in the inserter (optional) . - In this condition, the start lamp lights in green.
  • Page 135 7. WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL 1. Description of the flashing graphic symbols ... 2. Add paper symbol ... - Adding paper to the drawers ... 7-3 - Adding paper to the Tandem LCF (Large Capacity Feeder) ... 7-4 - Adding paper to the External LCF (Large Capacity Feeder)(optional) ...

  • Page 136: Description Of The Flashing Graphic Symbols

    1. DESCRIPTION OF THE FLASHING GRAPHIC SYMBOLS The graphic display on the touch panel shows the status of the copier. When one of the graphic symbols flashes, take the appropriate action referring to the page shown. When one of the graphic symbols flashes, press the HELP key to display the guidance.

  • Page 137: Add Paper Symbol

    2. ADD PAPER SYMBOL Adding Paper to the Drawers When the paper supply in the selected drawer or Tandem LCF (Large Capacity Feeder) runs out, the drawer or External LCF (Large Capacity Feeder)(optional) shown on the display flashes, and the fol- lowing message appears: Add paper Add paper as follows.

  • Page 138: Adding Paper To The Tandem Lcf (Large Capacity Feeder)

    2. ADD PAPER SYMBOL (Cont.) Adding Paper to the Tandem LCF (Large Capacity Feeder) Pull the tandem LCF out carefully until it comes to a stop. - Be careful not to touch the drawer slide rail. Open some packages of paper, take out entire reams of paper and set them aligned in tray - When setting the paper, set the paper for side, and set it for...

  • Page 139: Adding Paper To The External Lcf (Large Capacity Feeder)(Optional)

    Adding Paper to the External LCF (Large Capacity Feeder)(optional) Pull the external LCF out carefully until it comes to a stop. - Be careful not to touch the drawer slide rail. Place the paper on the elevator tray. - Place the paper face up. - Maximum number of sheets that can be set - Fan the paper well, then place it on the elevator tray, align- ing it on the rear guide tray.

  • Page 140: Replace Toner Cartridge Symbol

    TONER CARTRIDGE Add toner This message will appear on the sceen. Use only toner cartridges made or designated by Sharp in order to optimize copy quality. Open the front cover. Rotate the left end of the holder, then pull out the empty toner cartridge with both hands as shown on the right.
  • Page 141 Holding the new toner cartridge as shown on the right, pull out the seal in the direction of the arrow. Match the label(orange) on the copier with the shutter(orange) on the toner cartridge, then insert the toner cartridge to the end. - If you cannot insert the toner cartridge completely, rotate it slightly to check the position and insert it again.
  • Page 142 3. REPLACE TONER CARTRIDGE Additional Explanation The life of the toner cartridge (number of copies) varies depending on the following conditions. Coverage of originals (printing ration of copies) varies depending on the following conditions : 1. Size and density of originals 2.

  • Page 143: Clear Paper Symbol

    4. CLEAR PAPER When a paper misfeed occurs in the copier,the is misfed. In that case, remove the misfed paper using the following procedure referring to the illustration below. - Moving the finisher (optional) Depending on where a paper jam has occurred, it may be necessary to move the optional finisher. ( including the inserter and the hole punch unit.) - Separating it from the copier While pressing the release lever...
  • Page 144 4. CLEAR PAPER Paper Misfeed in the Reversing Automatic Document Feeder Push the button on the reversing automatic document feeder to open the cover. Rotate the blue knob to remove any misfed originals. Lift the blue handle (first) as shown on the right. - If there are any misfed originals, remove them.
  • Page 145 Lift the blue handle (second) as shown on the right. - If there are any misfed originals, remove them. Lift the original feeding tray and remove any misfed originals. Open the original exit tray and remove any misfed originals. Lifting the handle in the direction of the arrow, pull it toward you.
  • Page 146 4. CLEAR PAPER Paper Misfeed inside of the Copier Open the paper feed cover. - When installing the external LCF (optional), open the paper cover after doing step 1 of page 7-15. Remove any misfed paper. Open the bypass cover. Remove any misfed paper.
  • Page 147 Open the exit cover. - For how to connect or separate the optional finisher. Page 7-9 Remove any misfed paper. - If any paper is misfed in the cover, pull it out. Caution Do not touch the metal area of guide plate in the automatic duplexer.
  • Page 148 4. CLEAR PAPER Pull the transfer unit out until it comes to a stop. - If a sheet of paper is misfed on the transfer belt, remove it. - Do not put some objects on the transfer belt or do not touch it. - When a sheet of paper is caught in fuser unit, do not pull out directly but remove based on step 9.
  • Page 149 Paper Misfeed on the Bypass Guide Pull up the misfed paper slowly on the bypass guide. Paper Misfeed in the External LCF (Large Capacity Feeder) (optional) Pull the external LCF away from the copier slowly while pressing the release lever. Remove any misfed paper by turning the blue knob in the direction of the arrow.
  • Page 150 4. CLEAR PAPER Open the cover of the external LCF and remove any misfed paper. - Be careful not to touch the drawer slide rail. Be careful not to let your fingers be caught when closing the drawer. Return the external LCF to its original position. - As shown in the figure on the right, place your hands on to enable you to slowly reconnect it to the copier while maintaining both machines parallel to one another.
  • Page 151 Pull down the grip. Remove any misfed paper. Jammed paper might not be able to be removed while the hole punch unit is used. In this case, perform the steps in Paper Misfeed in the Hole Punch Unit Open the tray of the inserter to remove any misfed paper.
  • Page 152 4. CLEAR PAPER Rotate the blue knob to locate the arrow within the area on the label. - Under this condition, the punchers are up, allowing the pa- per shown in the figure to be removed. Paper Misfeed in the Finisher (optional) Open the upper cover of the finisher.
  • Page 153 Lift knob and then remove any misfed paper. is indicated in the illustration of step 2 on page 7-18.) Remove any misfed paper from the paper exit area. Paper Misfeed in the Saddle Stitch Unit (optional) * Only when the saddle stitch finisher (AR-F12) is installed. When installing the optional inserter, open the lower cover of the inserter.

  • Page 154: Saddle Stitch Unit (Optional)

    4. CLEAR PAPER Remove any misfed paper. Open the lower cover of the finisher. Turn the right-hand knob push the left-hand knob Remove any paper misfed on the exit side of the saddle stitch unit. Open the exit cover of the saddle stitch unit and remove any misfed paper.

  • Page 155: Adding Staples (Optional)

    5. ADDING STAPLES (OPTIONAL) When the staple cartridge runs out of staples, if the optional finisher is installed, the following message appears: Set staple cartridge Add staples to the cartridge according to the procedure below. Finisher Open the front cover of the finisher. Lower the blue lever in the stapler and slide out the staple cartridge.
  • Page 156 5. ADDING STAPLES (OPTIONAL) (Cont.) Pull out the seal holding the staples straight upward. Return the staple cartridge to its original position. - Insert the cartridge until it is caught by the claw and fixed with a click sound. Close the front cover of the finisher. If the following message remains displayed, repeat the above procedure from Set staple cartridge...
  • Page 157 Pull out the grip of the saddle staple holder you and turn it clockwise in the direction of the arrow. Remove the empty staple case and set a new one. - Replace both staple cases with new ones. - Do not remove the seal holding the staples before the staple case is set in the cartridge.

  • Page 158: Removing Jammed Staples (Optional)

    Holding the knob, lower part Caution Do not touch the stapling area. The stapler could injure you. Remove any jammed staples using your fingertip or something sharp. Holding the knob, return part position. 7-24 WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL Finisher ”...
  • Page 159 Return the staple case to its original position. - Insert the cartridge until it is caught by the claw and fixed with a click sound. Close the front cover of the finisher. Saddle Stitch Unit Perform steps 1 to 3 of the procedure for “ 5. ADDING STAPLES Saddle Stitch Unit ”...
  • Page 160 6. REMOVING JAMMED STAPLES (OPTIONAL) (cont.) Return the staple case to its original position. 7-26 WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL...

  • Page 161: Disposing Accumulated Punched Paper Bits (Optional)

    7. DISPOSING OF ACCUMULATED PUNCHED PAPER BITS (OPTIONAL) When paper bits punched from copies have accumulated to a certain level, the following message appears. Please Dispose of Hole Punch Dust Dispose of the paper bits as described below. Open the cover of the hole punch unit. Holding the black handle, slide out the case containing the paper bits, and dispose of them properly.

  • Page 162: Clear Paper Symbol

    8. CALL SERVICE CALL SERVICE SYMBOL When the CALL SERVICE possible. Call your service technician. Call for service When the CALL SERVICE the digital key 8 together before you turn off the power, the corresponding error code will appear on the copy quantity display only while both keys are held down.

  • Page 163: Maintenance

    8. MAINTENANCE 1. Daily inspection ... 2. Simple troubleshooting ...

  • Page 164: Daily Inspection

    1. DAILY INSPECTION Items for Daily Check Power switch ON/OFF status We recommend turning the power switch ON at the startup everyday so that copies can be made whenever you want. Also, be sure to turn the power switch OFF when you leave the office. In the following cases, do not turn the power switch OFF.

  • Page 165: Simple Troubleshooting

    2. SIMPLE TROUBLESHOOTING Check the following items, and if the problem still occurs, call service for assistance. Copier does not start Items to be checked Is the power cord plug firmly Insert the power cord plug firmly. inser ted in the outlet? Is the front cover, the side cover Close the covers properly.
  • Page 166 2. SIMPLE TROUBLESHOOTING (Cont.) Copy density is too high Is the copy density adjustment set darker than is standard? Copies are stained Is the reversing automatic docu- ment feeder firmly closed? Is the original cover or the trans- port belt of the reversing auto- matic document feeder dirty? Is the scanning area dirty? Is the copy density set properly?
  • Page 167 9. SPECIFICATIONS & 1. Specifications ... 2. Specifications of options ... 3. Packing list ... 4. Index ... OPTIONS...

  • Page 168: Specifications & Options

    Tandem LCF: 2500 sheets (20lb. Bond) Sheets bypass: 100 sheets (20lb. Bond) Magnetic auto-toner system Automatic plus manual selection from 11 exposure step Xenon lamp 115V, 50/60Hz, 20A AR-651/810: 2.0kw " " 27.48 (W) x 30.59 (D) x 47.76 "...
  • Page 169 * The bypass copying speed is as listed above when specifying the paper size, however when the paper size is not specified, the copy speed of all sizes is on ‘ *2’. * This specification varies depending on copying condition and environment. AR-651 Feeder Face up...

  • Page 170: Specifications Of Options

    2. SPECIFICATONS OF OPTIONS Finishers Model Name Type Acceptable Paper Size Acceptable Paper Weight Number of Copies Stapled at a Time (AR-F11, AR-F12) Stapling Position Saddle Stitch Unit Stitching Capacity Hole Punch Unit Power Source Dimensions Weight Power Consumption * The values inside in parentheses are measured when the subtray is pulled out. Tray Loading Capacity Mode Non-Sort...
  • Page 171 Dimensions Weight Power Consumption * The paper mentioned above is Sharp-recommended paper. Specifications and appearance are subject to change without notice in the interest of product improvement. Paper Weight : 16 lb. Bond - 140 lb. Index Available paper sizes...

  • Page 172: Packing List

    Packing List * Specifications and appearance are subject to change without notice in the interest of product improvement. Acoustic Noise Emission (measurement according to ISO7779) AR-651 Sound power level L * Accessory included in basic model AR-810 Sound power level L...

  • Page 173: Index

    4. INDEX Numbers 2 IN 1 ... 4-12 2 IN 1 DUPLEX ... 4-12 2 IN 1/4 IN 1 ... 4-12 4 IN 1 ... 4-12 4 IN 1 DUPLEX ... 4-12 Acceptable Copy Paper Types and Sizes ... 2-4 Acceptable Original Types and Size ...
  • Page 174 4. INDEX (Cont.) Duplex Copying ... 3-7 Edge Erase ... 4-4 ENERGY SAVER key ... 1-5 Entering Letters ... 5-28 Exit cover ... 1-2 Exiting Copy Papers ... 2-3 Exiting Originals ... 2-11 External LCF ... 9-5 Feed side cover ... 1-2 Finisher ...
  • Page 175 Paper Misfeed in the Saddle Stitch Unit AR-F12 ... 7-19 Paper Misfeed on the Bypass Guide ... 7-15 Papers Acceptable to Set in the Inserter ... 6-9 Periodic Maintenance Message ... 7-28 Power switch ... 1-2 Precautions ... 7 Precautions for Using the Reversing Automatic Document Feeder ...
  • Page 176 4. INDEX (Cont.) When Coming Across the Situations below ... 2-3 When Placing an Original on the Glass ... 2-10 When this message appears: "Wait" ... 2-3 When Using the Reversing Automatic Document Feeder ... 2-11 X-Y Zoom ... 4-7 9-10 SPECIFICATIONS &...
  • Page 177 Sharp. You should be aware, however, that Sharp does not itself extend any warranties, either express or implied, directly to you, the end-user and no one is authorized to make any representations or warranties on behalf of Sharp.

  • Page 178: Sharp Corporation

    AR-651/AR-810 SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135. www.sharp-usa.com SHARP ELECTRONICS OF CANADA LTD. 335 Britannia Road East, Mississauga, Ontario, L4Z 1W9 SHARP CORPORATION PRINTED IN JAPAN XXXXXXXXXXXX...

This manual is also suitable for:

Ar-810

Table of Contents