Chapter 6: Infrared Beam Wiring; Section 6A: Wiring(1)HoldingBeam - Nabco GT 1175 Installation Manual

ElectricalInstallationManualU-30"D"Control
Part #C-00121
CHAPTER 6: INFRARED BEAM WIRING
Section 6a: Wiring (1) Holding Beam
On GT-1175 Slide doors, the Optex OS-12C Module Infrared Beam is installed and wired at the
NABCO factory. This unit is shipped complete with the following:
► Emitter ►
► Receiver ►
► Control Box ►
Both the Emitter and Receiver are flush mounted on both sides of the Slide door Frame or each
Jamb tube, directly across from each other. A pulsed, infrared light beam is used to continuously
transmit across the Slide door opening. Interruption of the infrared light beam will switch the
White holding beam input wire to Red (Common). Thus causing the system to re-activate and
Hold Open until the interruption is cleared. Please Figure 6-1.
AC115V ± 10%
50 / 60 Hz
TB1
12 VDC+
12VDC-
(Common)
Holding Beam
Reduced Opening Switch
Mode Switch
Breakout Detector
Sidelite Presence Sensor
Contact Output
(Class2 Load only)
30V (42.4V peak) max.
5A max, (0-20V), 3.2A max.
(20-30V)
Auxiliary Output
(Open Collector)
12VDC Common
U30 MICROPROCESSOR CONTROL LABEL
DN 0547
6-20
POWER SUPPLY
P/N 14-11741
NOISE
T1
FILTER
TB2
-CIRCUIT-
-BREAKER-
RED INDICATES
POWER IS OFF
PRESS POWER SUPPLY
TO ASSEMBLY
RESET P/N 9418800100
NABCO
ENTRANCES, INC.
14-11741
S1
9DC 12V 1
7 2
61 3
6B 4
H
5
M0
6
M1 7
62 8
SQ 9
BA
10
SLS 11
Out.A
N/O 12
N/C Out.B 13
Out.C 14
Common
Out 15
7 16
U30 TERMINAL
P/N 14-11873
YELLOW
TERM #11
YELLOW
GRAY
TERM #7
TERM #10
MOTOR/OPERATOR
P/N 24-11327
12
7 0
BROWN & RED
CIRCUIT 1 & 2
1
2 RED
3
4
WHITE
5
6
7
8
9
10
11
TERM #5
12
13
14
15
16 Optex OS-12C
Controller
P/N 14-9710-03
TERM #13
BLUE
TERM #6
GRAY
EMTR 1
Figure 6-1 (1) Holding Beam using Optex OS-12C Controller
www.NabcoEntrances.com
U30 MICROPROCESSOR CONTROL
P/N 24-8901-30
! WARNING
No.
! To protect against risk of Fire
MOTOR 12P
or electric shock,use only the
Microprocessor Controller
cer fied NABCO power supply.
248901-
Mode SW Usage
POWER M0 M1 MODE
NABCO
Open Open TWO WAY FUNCTION (SLIDING DOOR)
61
Gn d Open ONE WAY 12VDC +
GYRO TECH
12VDC-(Common)
6B Gn d Gn d HOLD OPEN
Open Gn d NIGH T Interior Ac va o n
H Holding Beam
Reduced Opening Switch
62 ! CAUTION
Mode Switch (see Mode SW Usage shown le )
BA
Exterio r Ac va on
ERROR ! Sequen al Ac va on
Adjustments to the door can only be made
with the NABCO Handy Terminal. Breakout Detector
Sidelite Presence Sensor
Contact Output (Class2 Load only)
Do not disassemble the control box.
30V(42.4Vpeak)max
There are no user serviceable parts
5Amax.(0-20V), 3.2Amax.(20-30V)
inside.
Auxiliary Output (Open-Collector)
!
To maintain warranty,repairs must be 12VDC-(Common)
made by authorized NABCO facilities.
CONNECT
EACH TERMINAL
THE SAME
TERM #1
Yellow
Braided Shield
TERM #6
OTHER WIRES NOT SHOWN
FOR SIMPLICITY
BLUE
RCVR 1
InfraredBeamWiring
Rev. 8-25-16
HANDY TERMINAL 6P
SYMBOL No.
9DC12V 1
7 2
61 3
6B 4
H 5
M0 6
M1 7
62 8
SQ 9
BA 10
SLS 11
N/O OUT. A 12
N/C OUT. B 13
Common OUT. C 14
OU T 15
7 16
Jacket Color