Vibration Isolators - Daikin WGZ030DW Installation And Maintenance Manual

Vibration Isolators

It is recommended that isolators be used on all upper level
Vibration Isolators
installations or in areas where vibration transmission is a
consideration.
Figure 7: Isolator Locations
4 LB
1
LF
Table 7: Isolator Kit Part Numbers
WGZ-DW Packaged Chiller Isolator Kit Part Numbers
Model Num ber 030-060
Spring-Flex 332320501
332325501
R-I-S
WGZ-DA Remote Condenser Isolator Kit Part Numbers
Model Num ber 030-060
Spring-Flex 332320506
R-I-S 332325504
Table 8: Vibration Isolator Mounting Locations (Packaged Chillers)
Unit Spring-Flex Mountings
Size M1
ID-900
WGZ030DW
Green
ID-900
WGZ035DW
Green
ID-900
WGZ040DW
Green
ID-900
WGZ045DW
Green
ID-900
WGZ050DW
Green
ID-900
WGZ055DW
Green
ID-900
WGZ060DW
Green
ID-1350
WGZ070DW
Purple
ID-1350
WGZ080DW
Purple
ID-1800
WGZ090DW
Green
ID-1800
WGZ100DW
Green
28
RB 3
Water
Connections
2
FRF
Control Panel
070-080 90
332320502 332320503
332325502 332325502
070-080 090-115
332320507 332320508
332325501 332325501
M2 M3 M4
ID-900 ID-900 ID-900
Green Green Green
ID-900 ID-900 ID-900
Green Green Green
ID-900 ID-900 ID-900
Green Green Green
ID-900 ID-900 ID-900
Green Green Green
ID-900 ID-900 ID-900
Green Green Green
ID-900 ID-900 ID-900
Green Green Green
ID-900 ID-900 ID-900
Green Green Green
ID-1350 ID-1350 ID-1350
Purple Purple Purple
ID-1350 ID-1350 ID-1350
Purple Purple Purple
ID-1800 ID-1800 ID-1800
Green Green Green
ID-1800 ID-1800 ID-2400
Green Green Gray
Transfer the unit as indicated under "Moving the Unit." In all
cases, set the unit in place and level with a spirit level. When
spring-type isolators are required, install springs running under
the main unit supports.
The unit should be set initially on shims or blocks at the listed
spring free height. When all piping, wiring, flushing, charging,
etc., is completed, the springs are adjusted upward to loosen
the blocks or shims that are then removed.
A rubber anti-skid pad should be used under isolators if hold-
down bolts are not used.
Installation of spring isolators requires flexible piping
connections and at least three feet of flexible electrical conduit
to avoid straining piping and transmitting vibration and noise.
Refer to unit dimension drawing for mounting locations.
100-130 150-200
332320504 332320505
332325503 332325503
130 150-200
332320509 332320510
332325501 332325505
R-I-S Mountings
M1 M2
RP-3 RP-3
Gray Gray
RP-3 RP-3
Gray Gray
RP-3 RP-3
Gray Gray
RP-3 RP-3
Gray Gray
RP-3 RP-3
Gray Gray
RP-3 RP-3
Gray Gray
RP-3 RP-3
Gray Gray
RP-4 RP-4
Brow n Brow n
RP-4 RP-4
Brow n Brow n
RP-4 RP-4
Brow n Brow n
RP-4 RP-4
Brick Red Brick Red Brick Red Brick Red
M3 M4
RP-3 RP-3
Gray Gray
RP-3 RP-3
Gray Gray
RP-3 RP-3
Gray Gray
RP-3 RP-3
Gray Gray
RP-3 RP-3
Gray Gray
RP-3 RP-3
Gray Gray
RP-3 RP-3
Gray Gray
RP-4 RP-4
Brow n Brow n
RP-4 RP-4
Brow n Brow n
RP-4 RP-4
Brow n Brow n
RP-4 RP-4
IM 1131-2