Scheppach basato 3 Manual page 12

• The working space on the machine must be free of chips
and wood scrap.
• Wear only close-fitting clothes. Remove rings, bracelets
and other jewelry.
• Always wear safety goggles when working.
• Wear a cap or hair net to protect long hair.
• Wear suitable gloves to change the sawband.
• Do not wear work gloves when working on the saw.
• Observe the correct rotational speed setting on the ma-
chine.
• The safety mechanism on the machine may not be re-
moved or rendered unusable.
• Cleaning, changing, calibrating, and setting of the
machine may only be carried out when the motor is
switched off. Pull the power supply plug and wait for the
rotating tool to completely stop.
• Connection and repair work on the electrical installation
may be carried out by a qualified electrican only.
• All protection and safety devices must be replaced after
completing repair and maintenance procedures.
• Switch the machine off and pull power supply plug when
rectifying any malfunctions.
• Use a suction unit to suck up wood shavings and saw-
dust. The current speed at the suction connection piece
should be 20 m/s.
• Check the saw band guide and the saw band tension
before starting up.
• Do not use nicked saw bands or those that have an al-
tered form.
• Replace table inserts that have worn saw slots.
• When sawing round wood, make sure that the work piece
does not turn.
• For sawing heavy
use the appropriate
(Special accessory roller stands).
• Place the upper saw band guide as closely as possible
to the work piece.
• On slanted table plates, attach the longitudinal stop on
the lower table plate half.
• Do not brake the saw band with side pressure after
switching off.
• Remove work pieces that have become stuck only with
the motor switched off and with the saw band at a
standstill.
• Cut off the external power supply of the machine even
if only minor changes of place are envisaged. Properly
reconnect the machine to the supply mains before re-
commissioning.
• When leaving the work place, switch the motor off. Pull
the power supply plug.
8
or cumbersome pieces,
working aids for bracing.
Use only as authorized
 CE tested machines meet all valid EC
machine guidelines as well as all
relevant guidelines for each machine.
• All protective and safety device must be mounted on the
machine before beginning work.
• The machine is designed to be operated by one person.
The operator is responsible for all other persons in the
working area.
• Observe all safety instructions and warnings attached to
the machine.
• See to it that safety instructions and warnings attached
to the machine are always complete and perfectly leg-
ible.
• The bandsaw with the supplied tools and accessories is
designed exclusively for sawing wood, material similar to
wood, and non-ferrous metals and steel.
• The maximum dimensions for workpieces to be pro-
cessed is may not exceed the bench size in the standard
version. Clearance width: 306 mm, Clearance height:
205 mm
• For larger workpiece dimensions which require tipping
of the table top, the table extension or the dolly (special
accessories) must be used.
• The band saw can also be used for sawing metal when
it is equipped with a special saw band dolly (special ac-
cessory) and a operated at an adapted cutting speed.
Metal allows with more than 80 % magnesium may not
be processed due to the danger of fires.
• When used in enclosed rooms, the machine must be
connected to a vacuum exhaust unit. Use the dust ex-
tractor to remove matchwood or saw dust. The vacuum
support flow rate must be 20 m/s. Subatmospheric
pressure 860 Pa.
• The automatic switching unit is available as a special
accessory.
Type ALV 2 Art. No. 7910 4010 230 V/50 Hz
Type ALV 10 Art. No. 7910 4020 400 V/230 V/50 Hz
• The vacuum exhaust unit automatically switches on af-
ter a 2-3 second delay after the machine tool is turned
on. This avoids overloading the circuit fuse.
• After turning off the machine tool, the vacuum exhaust
unit remains on for an additional 2-3 seconds and is
then automatically switched off. Remaining dust is
thereby removed by vacuum exhaust, as required by
German regulations governing hazardous materials. This
results in savings in electricity consumption and reduc-
es noise levels, as the vacuum exhaust unit is on only
during machine tool operation.
• A suction device which conforms with commercial regu-
lations must be used for suction in commercial areas.
• Do not switch off or remove suction units or dust extrac-
tors while the work machine is in operation.
• The machine must only be used in technically perfect
condition in accordance with its designated use and the
instructions set out in the operating manual, and only
by safety-conscious persons who are fully aware of the
risks involved in operating the machine. Any functional
disorders, especially those affecting the safety of the
machine, should therefore be rectified immediately.
• The safety, work and maintenance instructions of the
manufacturer as well as the technical data given in the
calibrations and dimensions must be adhered to.
• Relevant accident prevention regulations and other, gen-
erally recognized safety-technical rules must also be ad-
hered to.
• The machine may only be used, maintained, and op-
erated by persons familiar with it and instructed in its
operation and procedures. Arbitrary alterations to the
machine release the manufacturer from all responsibility
for any resulting damages.
• The machine may only be used with original accessories