Maintenance And Care - Flex LRP 1503 VRA Original Operating Instructions

Operating instructions
klqb
tÜÉå=íÜÉ=ÄÉäí=ë~åÇÉê=áë=ëïáíÅÜÉÇ=çÑÑI=
íÜÉ ÖêáåÇáåÖ=íççä=ÅçåíáåìÉë=êìååáåÖ=ÄêáÉÑäóK
A belt sander has the following advantages over
a grinding disc:
– cool sanding,
– clean finish without grooves,
– high stock removal rate,
– high productivity on account of large angle
of contact (depending on diameter).
Sanding
– Pipes are machined between the rollers
8 and 11.
– The angle of contact and the stock removal
rate can be varied by the contact pressure.
– The smaller the pipe diameter, the larger the
possible angle of contact. Up to 270° are
possible.
Sealing the surface
Many manufacturers recommend sealing
finished surfaces with a protective spray
(see Flex stainless steel accessories).
For further information on the manufacturer's
products go to www.flex-tools.com.
18

Maintenance and care

t^okfkd>
_ÉÑçêÉ=éÉêÑçêãáåÖ=~åó=ïçêâ=çå=íÜÉ=ÄÉäí=
ë~åÇÉêI=éìää=çìí=íÜÉ=ã~áåë=éäìÖK
Cleaning
t^okfkd>
fÑ=ãÉí~äë=~êÉ=ÖêçìåÇ=çê=Åìí=çîÉê=~=éêçäçåÖÉÇ=
éÉêáçÇI=ÅçåÇìÅíáîÉ=Çìëí=ã~ó=ÄÉÅçãÉ=
ÇÉéçëáíÉÇ=áåëáÇÉ=íÜÉ=ÜçìëáåÖK=fãé~áêãÉåí=çÑ=íÜÉ=
éêçíÉÅíáîÉ=áåëìä~íáçå>=léÉê~íÉ=íÜÉ=éçïÉê=íççä=îá~=
~=êÉëáÇì~äJÅìêêÉåíJçéÉê~íÉÇ=ÅáêÅìáíJÄêÉ~âÉê=
EíêáééáåÖ=ÅìêêÉåí=PM=ã^FK
 Regularly clean the power tool and
ventilation slots. Frequency of cleaning is
dependent on the material and duration
of use.
 Regularly blow out the housing interior and
motor with dry compressed air.
Carbon brushes
The belt sander features cut-off carbon
brushes.
When the wear limit of the cut-off carbon
brushes is reached, the belt sander switches off
automatically.
klqb
rëÉ=çåäó=çêáÖáå~ä=é~êíë=ëìééäáÉÇ=Äó=íÜÉ=
ã~åìÑ~ÅíìêÉê=Ñçê=êÉéä~ÅÉãÉåí=éìêéçëÉëK=
fÑ åçåJçêáÖáå~ä=é~êíë=~êÉ=ìëÉÇI=íÜÉ=Öì~ê~åíÉÉ=
çÄäáÖ~íáçåë=çÑ=íÜÉ=ã~åìÑ~ÅíìêÉê=ïáää=ÄÉ=ÇÉÉãÉÇ=
åìää=~åÇ=îçáÇK
When the power tool is being used, the carbon
brushes can be seen sparking through the rear
air inlet apertures.
If the carbon brushes spark excessively, switch
off the belt sander immediately. Take the belt
sander to a customer service workshop
authorised by the manufacturer.
Gears
klqb
aç=åçí=äççëÉå=íÜÉ=ëÅêÉïë=çå=íÜÉ=ÖÉ~ê=ÜÉ~Ç=
ÇìêáåÖ=íÜÉ=ï~êê~åíó=éÉêáçÇK=kçåJÅçãéäá~åÅÉ=
ïáää=ÇÉÉã=íÜÉ=Öì~ê~åíÉÉ=çÄäáÖ~íáçåë=çÑ=íÜÉ=
ã~åìÑ~ÅíìêÉê=åìää=~åÇ=îçáÇK
LRP 1503 VRA