Page 1
A S S E M B LY - A N D I N S T R U C T I O N S M A N U A L Scan 68 Series Congratulations on your new Scan wood-burning stove You have purchased a product by one of Europe’s leading manufacturer’s of wood-burning stoves, and we are sure that you will have years of pleasure with your purchase.
C O N T E N T S Table of contents Technical data ......................3 Installation Safety Technical data and dimensions Dimension sketch Product registration number Type plate Assembly ........................10 Additional accessories Service box Loose parts Remove packaging Removal of the self-closing door spring Mounting of the base/wall fitting Load bearing foundation Floor plate...
Any changes made to the product by the dealer, installer or user could result in the product and safety functions not functioning as intended. The same applies to the fitting of accessories or extra equipment not supplied by Scan A/S. This could also be the case if parts that are necessary for the operation and safety of the stove are dismantled or removed.
Page 4
T E C H N I C A L D ATA Portal Wall Pedestal Without lateral glass panes Simple Portal Simple Portal Simple Portal Simple Portal High Top High Top With steel sides Wall Pedestal Portal With lateral glass panes...
Surface treatment: ................Senotherm before refuelling. Max. wood length: ..................33 cm The Scan 68 - series was build in compliance with the homologized product type specified in the Assembly- and Instructions Manual Weight Scan 68-1/2/7/8 : ............ca. 98 kg provided with the product.
Page 6
T E C H N I C A L D ATA Dimension sketch Scan 68-1, Scan 68-2, Scan 68-7 + Scan 68-8 250*** Centre rear outlet Height to the beginning of the connecting piece at top outlet Centre of fresh air intake bottom...
Page 7
T E C H N I C A L D ATA Dimension sketch Scan 68-5, Scan 68-6, Scan 68-11 + Scan 68-12 250*** 175*** Centre rear outlet Height to the beginning of the connecting piece at top outlet Centre of fresh air intake...
T E C H N I C A L D ATA Dimension sketch Scan 68-13 HT + Scan 68-14 HT 250*** 147*** 250*** 147*** Centre rear outlet Height to the beginning of the connecting piece at top outlet Centre of fresh air intake...
STI: Bottom view Disposal of packaging Your Scan stove may come supplied with the following packaging: Wood packaging: The wood packaging can be reused and after final use can be incinerated as a CO2 neutral product or sent for recycling.
Page 12
Check that the stove is not damaged before starting to install it. Check that the stove is not damaged before starting to install it. Scan 68-13 and Scan 68-14 comes attached to a wooden pallet on delivery. To remove the packaging, see the illustrations below.
Page 13
A S S E M B LY A ( 1 : 5 ) Mounting of the burn chamber on the basel There are two bases and a wall fitting for Scan 68. Scan 68-9 /Scan 68-10 Pedestal When the stove has been placed on the base, the four screws must be remounted.
Page 15
The stove must only be fitted to a non-flammable wall. There must be no form of flammable component in the wall. In the case of thin walls, Scan A/S disclaims all liability for the installation of wall-hung nor must there be any behind the wall. The load-bearing capacity of wood-burning stoves.
Page 18
Use the line or a spirit level. Drill the necessary holes and mount the screws. klargøring til vægbeslag Scan 68 NAVN: EMNE: MATERIALE: VÆ DIMENSION: AREAL: C:\Working Folder\Designs\Scan 68\90068058.idw STI: vægbeslag på væg 90068061 EMNE: TG.NR: justeringsskive til vægbeslag Scan 68 NAVN: EMNE: VÆGT:...
Page 19
See page 15. The two screws under the stove must be removed, before lifting the stove up on the wall fitting. If you want a rear outlet, see page 23 mont skruer væghængt Scan 68 9006806 NAVN: EMNE: TG.NR: DATO:...
950 mm Your local Scan dealer can advise you on regulations concerning flammable materials in the vicinity of your stove. without lateral glass panes 1100 mm The idea behind the floor plate is that it protects the floor and flam- mable material against sparks.
A S S E M B LY A S S E M B LY Distance to flammable materials, shown with un-insulated flue pipe Scan 68 45° Corner installation Parallel rear wall installation *100/**350 *150/*150 * without lateral glass panes * without lateral glass panes...
6" chimney can be used. Connection with 90° elbow pipe If you intend to use an elbow pipe with the Scan 68 we recommend the use of a curved elbow pipe to improve the draft. If you are connecting your stove using a sharp elbow bend, the clea- nout door should be in the vertical section, such that the horizontal part can be cleaned through it.
Page 26
A S S E M B LY Fitting natural stone Scan 68-15 and Scan 68-16 are supplied with loose pieces of natural stone that are fitted to the sides of the stove. Natural stone is made from a natural material and consequently its A ( 1 : 2 ) pattern and shape may vary.
A C C E S S O R I E S Mounting of high top for Scan 68-13/14 High Top for natural stone A sealing strip, four M5x10 screws with flange and four spacer If you choose to connect the stove with an elbow pipe or a rear out- bushes are supplied.
Page 28
A C C E S S O R I E S Wall mounting kit for Scan 68 with high top Use the six screws that If you choose to connect the stove with an elbow pipe or a rear out- are supplied with the High Top.
Page 30
Heat accumulating stones for high top The heat accumulating stones for Scan 68 with high top are made of a special material with a high heating capacity. The stones are heated up during the firing and gives off the heat again after the firing, which means that the stove stays warm for a longer time.
We recommend the use of fire starters, or similar products, which are Important! Always use a top-down lighting. The stove is constructed available from your Scan dealer. Using fire starters helps to light the for this in order to give the best exploitation.
You can use any type of wood as fuel. will take longer to reach operating temperature than a steel chim- The Scan 68 appliance models detailed on page 3 of this manual have ney). It is very important to reach operating temperature as quickly...
If you use oak or beech wood fuel, note that these wood types have a greater fuel value than, say, birch. Make sure you Scan A/S recommends that you check your stove thoroughly after use less fuel to avoid damage to the wood-burning stove.
The surface of the stove is turning grey product or its accessories. • Overheating (see instructions for heating) • This warranty is only valid in the country to which this Scan pro- duct was originally supplied. Poor heating performance of stove Always use original replacement parts, or parts recommended by the •...
This screw (M5 x 10) must be placed as shown in the pictures, to prevent secondary air control can be closed completely. After mounting the UK screw Open both, secondary and primar air control to mount the screw. A ( 0,40 : 1 ) Scan 68 skrue uk mont 90068079 NAVN: EMNE: TG.NR:...