Related Manuals for Sunny Health & Fitness SF-E602
Summary of Contents for Sunny Health & Fitness SF-E602
- Page 1 USER MANUAL SF—E602 ELLIPTICAL TRAINER PLEASE READ THIS MANUAL BEFORE STARTING ASSEMBLY AND OPERATING ON THIS EQUIPMENT. KEEP THIS MANUAL AS FURTURE REFERENCE.
- Page 2 General safety instructions In the design and the production of this fitness equipment, much attention has been paid to safety. Nevertheless, you need at all times to remain conscious of certain safety measures. Make certain that you have carefully read through the whole user manual prior to your use of the equipment. Keep in mind the following points: 1.
- Page 3 Warning Consult with your physician prior to starting your exercises. A frequent and intensive training programme should first be approved by your family physician. This is especially important for individuals above 35 years of age or for those with physical problems. Carefully read through the entire user manual before you start exercising.
- Page 4 PRODUCT OVERVIEW: 手握心跳 MEGA HAND PULSE 右上扶手管组 RIGHT UPPER SWING BAR 握把管 ROUND GRIP BAR 仪表 左上扶手组 METER LEFT UPPER SWING BAR 握把饰盖 ROUND GRIP BAR HOUSING TCD阻力调节器 TCD Tension control device 扶手饰盖 SWING BAR HOUSING 下扶手组 LOWER SWING BAR METRE POST BOTTOM HOUSING 仪表杆护盖...
- Page 5 ASSEMBLY TOOL & ASSEMBLY DIAGRAM Please identify the following assembly tools’ sketch photo illustration which will be helpful in the process of assembly. NAME & SPEC DRAWING QTY. NAME & SPEC DRAWING QTY. M4*35 ROUND CROSS SCREW OD20*ID8.5*2.0T FLAT WASHER M4*20 ROUND CROSS SCREW M8*20 CARRIAGE SCREW M10*50 CARRIAGE SCREW...
-
Page 6: Front Stabilizer
1. FRONT STABILIZER － Attach the front stabilizer (52) to the front bottom of main frame. Insert an M8*72 inner hexagon screw (51) through an M8 spring washer (17), M8 arc washer (49) and front stabilizer as well the main frame. Lock this group tight. 2. - Page 7 4. METER POST － First please remove the two M8*70 inner hexagon screws (48), two M8 nylon caps (59), six M8 spring washers (17), two M8 arc washers (49), four M8*20 inner hexagon screws (16) and four OD20*ID8.5*2.0T flat washers which are pre-assembled on the bottom of the meter post.
- Page 8 6. Upper & lower swing bars － Remove M8*36 inner hexagon screws (7) and M8*6.35T nylon caps (9) which are pre-assembled on the L+R lower swing bars (18,94). － Move the right upper swing bar (92) close to the right lower swing bar (94);...
- Page 9 8. Round grip bar － Please remove the M8*25 screw (45), M8 spring washer (17) and OD20*ID8.5*1.5T flat washer (15) which are pre-assembled on the round grip bar (56). － Attach the round grip bar front housing (64) on the meter post.
- Page 10 Meter User Manual. BUTTON： 1.MODE：Press this button to select all functions and confirm all function values. Hold the button for 2 seconds to total reset all function values. 2.SET：Press to set function value. 3.RESET：Press to reset function value and back to last setting stage. Hold the button for 2 seconds to reset all function values and clear all functions.
-
Page 11: Exploded Diagram
EXPLODED DIAGRAM 34 35 34 15 17 16 77 19 78 98 99 36 50 51 17 49 52 41 50 79 80 90 91 68 85 86 87 88 35 34 36 37 33 17 15... -
Page 12: Part List
PART LIST NAME & SPECIFICATION QTY. NAME & SPECIFICAITON QTY. swing bar end cap front stabilizer swing bar foam sensor wire upper section mega hand pulse hand pulse wire 3 M3*10 hand pulse screw hand pulse wire 4 left upper swing bar round grip bar hand pulse wire 1 screw with TCD...