Function Button Setting - Sony PVM-X300 Operating Instructions Manual

Submenu
INPUT
1080I/PSF
18
Adjustment Using the Menus
Setting
Selects the input connector to be
used.
When SINGLE-LINK 3G/HD-
SDI or SINGLE-LINK 3G-SDI is
selected for SDI input
• INPUT 1: to use SDI IN
connector 1
• INPUT 2: to use SDI IN
connector 2
• INPUT 3: to use SDI IN
connector 3
• INPUT 4: to use SDI IN
connector 4
When DUAL-LINK 3G-SDI is
selected for SDI input
• INPUT 1&2: to use SDI IN
connectors 1 and 2
• INPUT 3&4: to use SDI IN
connectors 3 and 4
For HDMI input (SINGLE-LINK
HDMI)
• INPUT 1: to use HDMI input
connector 1
• INPUT 2: to use HDMI input
connector 2
• INPUT 3: to use HDMI input
connector 3
• INPUT 4: to use HDMI input
connector 4
For SDI input
Selects the display mode when the
1080i/PsF signal is input.
You can select one of the following
three options depending on the
input signal.
• 24PSF: for the 1080/24PsF signal
• 25PSF/50I: for the 1080/25PsF,
50i signal
• 30PSF/60I: for the 1080/30PsF,
60i signal
When INTERLACE is selected, the
I/P conversion signal is displayed.
When PSF is selected, the
progressive conversion (PsF to P)
signal is displayed.
Note
When AUTO is selected for the
SIGNAL FORMAT, the display
mode is automatically detected by
SDI Payload ID.
For HDMI input
This item cannot be accessed.
Submenu Setting
RGB RANGE Sets the black level and white level
(quantization range) for the RGB
format.
For SDI input
• FULL: 0 (black level) to 1023
• LIMITED: 64 (10bit)/256
For HDMI input
• FULL: 0 (black) to 255 (8bit)/
• LIMITED: 16 (8bit)/64 (10bit)/
HDMI AUTO Sets the manual or automatic
setting for the quantization range of
the HDMI signal.
• OFF: to set the quantization
• ON: to set the quantization range

FUNCTION BUTTON SETTING

USER CONFIG-FUNCTION BUTTON SETTING
xxxxx
F1 BUTTON:
xxxxx
F2 BUTTON:
xxxx
F3 BUTTON:
xxxxx
F4 BUTTON:
xxxxxx
F5 BUTTON:
xxxx
F6 BUTTON:
xxxxx
F7 BUTTON:
Submenu Setting
F1 BUTTON Assigns the function to the function
F2 BUTTON buttons F1 to F7 on the front panel.
F3 BUTTON
F4 BUTTON For the assignable functions, see
F5 BUTTON "Functions assignable to the function
F6 BUTTON buttons" (page 20).
F7 BUTTON
Factory setting
• F1 BUTTON: BRIGHTNESS
• F2 BUTTON: CONTRAST
• F3 BUTTON: CHROMA
• F4 BUTTON: BACKLIGHT
• F5 BUTTON: NATIVE SCAN
• F6 BUTTON: VOLUME
• F7 BUTTON: VIEW MODE
(10bit)/4095 (12bit) (white
level)
(12bit) (black level) to 940
(10bit)/3760 (12bit) (white
level)
1023 (10bit)/4095 (12bit)
(white level)
256 (12bit) (black level) to
235 (8bit)/940 (10bit)/3760
(12bit) (white level)
range manually using RGB
RANGE of the menu
automatically according to
the input signal