Download  Print this page

Function Button Setting - Sony LMD-2451MD Instructions For Use Manual

Hide thumbs

Advertisement

Table of Contents
Submenu
Setting
SUB INPUT
Sets the input signal of the sub display.
SELECT
You can select from among
COMPOSITE, Y/C, RGB,
COMPONENT, DVI, HD15, OPTION
A-1, OPTION A-2, OPTION B-1,
OPTION B-2, VIDEO WAVE and OFF.
Notes
• The multi display with COMPOSITE
• When you set SUB INPUT SELECT
• The input signal formats available for
POSITION
Sets the position of the sub display.
• 1: Top
• 2: Bottom
FRAME
Sets the position of the main display
when POP is selected in MULTI
DISPLAY.
• RIGHT: The main display is put by
• LEFT: The main display is put by the

FUNCTION BUTTON SETTING

USER CONFIG
FUNCTION BUTTON SETTING
F 1 B U T T O N :
F 2 B U T T O N :
F 3 B U T T O N :
F 4 B U T T O N :
Submenu
Setting
F1 BUTTON to F4
Assigns the function to the function
BUTTON
buttons of the front panel and turns the
function on or off.
You can assign the function from
among SCAN, ASPECT, EXT SYNC,
BLUE ONLY, MONO, MULTI
DISPLAY, APA, I/P MODE and
MIRROR IMAGE.
Factory setting
• F1 button: EXT SYNC
• F2 button: SCAN
• F3 button: ASPECT
• F4 button: MULTI DISPLAY
30
Adjustment Using the Menus
and Y/C, RGB and COMPONENT,
HD15 and DVI, OPTION A-1 and
OPTION A-2, and OPTION B-1 and
OPTION B-2 is not displayed.
to OFF, MULTI DISPLAY ENABLE
is set to OFF.
HD15 and DVI are limited. See "For
the multi display" (page 40).
the right side of the sub display.
left side of the sub display.
xxxx
xxxx
xxxx
xxxx
About the function assigned to the
function button
SCAN
Press to change the scan size of the picture. Press to
switch between NORMAL scan (0% scan), OVER scan
(20% over scan), FULL and NATIVE (see "Scan mode
image" on page 31). NATIVE is effective only when
1080i, 1080P or 720P signal is input. 1080P can be
selected when BKM-250TGM is installed.
The scan mode of the picture can also be changed when
MULTI DISPLAY ENABLE is set to ON. Selectable
scan modes vary depending on the settings in MULTI
DISPLAY (page 29). When FULL is selected as the
SIDE BY SIDE multi display mode, the size of the
picture is enlarged while keeping the aspect ratio the
same. In this case, the left and right edges of the image
are cut off.
ASPECT
Press to set the aspect ratio of the picture, 4:3 or 16:9.
EXT SYNC (external sync)
Press to operate the unit on an external sync signal
through the EXT SYNC IN connector.
EXT SYNC works when the component/RGB signals
are input.
BLUE ONLY
Press the assigned button to eliminate the red and green
signals. Only blue signal is displayed as an apparent
monochrome picture on the screen. This facilitates
"chroma" and "phase" adjustments and observation of
VCR noise.
MONO
Press the assigned button to display a monochrome
picture. When the buttons is pressed again, the monitor
switches automatically to color mode.
MULTI DISPLAY
Press the assigned button to display the multi display.
Set the multi display setting in the MULTI DISPLAY
SETTING menu (see page 29).
APA (Auto Pixel Alignment)
Press to adjust the picture automatically to maximum
clarity for the signal input to the HD15 input connector.
For finer according to the input signal, see "DOT
PHASE" on page 28.
When the menu screen or the multi display is displayed,
APA does not function.

Advertisement

Table of Contents

   Related Manuals for Sony LMD-2451MD

Comments to this Manuals

Symbols: 0
Latest comments: