Function Button Setting - Sony LMD-1951MD Instructions For Use Manual

Hide thumbs Also See for LMD-1951MD:
Table of Contents

Advertisement

Submenu
Setting
MULTI DISPLAY
Selects ON to display the multi display
ENABLE
and OFF not to display.
Notes
• When the frame frequency of the
main display is different from that of
the sub display, the picture may be
disturbed.
When no signal is input to the main
display, the picture may not be
displayed correctly.
• When you set SUB INPUT SELECT
to OFF, MULTI DISPLAY ENABLE
is set to OFF automatically.
• When MULTI DISPLAY ENABLE is
set to ON, APA (page 31) is not
available.
SUB INPUT
Sets the input signal of the sub display.
SELECT
You can select from among
COMPOSITE, Y/C, RGB,
COMPONENT, HD15, DVI, OPTION
A-1, OPTION A-2, OPTION B-1,
OPTION B-2, VIDEO WAVE and OFF.
Notes
• The multi display with COMPOSITE
and Y/C, RGB and COMPONENT,
OPTION A-1 and OPTION A-2, and
OPTION B-1 and OPTION B-2 is not
displayed.
• When you set SUB INPUT SELECT
to OFF, MULTI DISPLAY ENABLE
is set to OFF.
• The input signal formats available for
HD15 and DVI are limited. See “For
the multi display” (page 40).
POSITION
Sets the position of the sub display.
• 1: Bottom left
• 2: Bottom right
• 3: Top right
• 4: Top left
SUB PICTURE
Sets the sub display size.
SIZE
• 1: Small
• 2: Large

FUNCTION BUTTON SETTING

USER CONFIG
FUNCTION BUTTON SETTING
xxxx
F 1 B U T T O N :
xxxx
F 2 B U T T O N :
xxxx
F 3 B U T T O N :
xxxx
F 4 B U T T O N :
Submenu
Setting
F1 BUTTON to F4
Assigns the function to the function
BUTTON
buttons of the front panel and turns the
function on or off.
You can assign the function from
among SCAN, ASPECT, EXT SYNC,
BLUE ONLY, MONO, MULTI
DISPLAY, APA, I/P MODE, MIRROR
IMAGE and AUTO SYNC DETECT.
Factory setting
• F1 button: EXT SYNC
• F2 button: SCAN
• F3 button: ASPECT
• F4 button: MULTI DISPLAY
About the function assigned to the
function button
SCAN (Scan mode)
Press to change the scan size of the picture. Press to
switch between NATIVE, NORMAL scan (7% over
scan), UNDER scan (0% scan), OVER scan (20% over
scan), FULL and ZOOM (see “Scan mode image” on
page 31). NATIVE is effective only when 1080i, 1080p
or 720p signal is input. 1080p can be selected when
BKM-250TG is installed.
ASPECT
Press to set the aspect ratio of the picture, 4:3 or 16:9.
AUTO SYNC DETECT
Press the assigned button to detect external sync signals
and internal sync signals automatically.
The unit synchronizes with external sync signals when
they are detected. When external sync signals are not
detected, the unit synchronizes with internal sync
signals.
AUTO SYNC DETECT works when the component/
RGB signals are input.
AUTO SYNC DETECT does not work when signal is
input from BKM-229W.
EXT SYNC (external sync)
Press to operate the unit on an external sync signal
through the EXT SYNC IN connector.
EXT SYNC works when the component/RGB signals
are input.
If AUTO SYNC DETECT is on, this function is not
available.
MULTI DISPLAY
Press the assigned button to display the multi display.
Set the multi display setting in the MULTI DISPLAY
SETTING menu (see page 29).
SUB INPUT SELECT
Press the button to set the sub display input signal types
when the multi display is on. The mode switches in the
sequence COMPOSITE t Y/C t RGB t
Page 30

Advertisement

Table of Contents
loading

Table of Contents